Protech Systems MP-1060 User manual

USER’S
MANUAL
M
P
-
1060
Thermal Receipt Printer
M
P
-
10
60
M
1

Copyright Notice
MP-1060
Thermal Printer
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted in June 2015. You may not reproduce or transmit in
any form or by any means, electronic, or mechanical, including photocopying and
recording.
DISCLAIMER
This operation manual is meant to assist you in using the printer board. The
information contained in this document is subject to change without any notice.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual…................................................................
1-2
1-2 System Specification………………………………………….
1-3
1-3 General Specification….............................................................
1-4
1-4 Safety Precautions…..................................................................
1-6
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Unpacking…………………………………...…........................
2-2
2-2 Part Structure………..….….......................................................
2-5
2-3 Connectors.................................................................................
2-8
2-4 Installing and Replacing Roll Paper……...................................
2-9
2-5 Attaching and Removing the Connector Cover..........................
2-11
2-6 Attaching and Removing the Splash Proof Cover…..................
2-13
2-7 Attaching and Removing the Paper Guide.…………………....
2-13
CHAPTER 3 INSTALL AND SETUP
3-1 Install the printer……..........................................…..................
3-2
3-2 Setting the DIP Switch………………….…..……..…............
3-3
3-3 DIP Switches functions…...……………………………………
3-4
3-4 Adjusting the Paper-near-end sensor..…………..………..........
3-8
CHAPTER 4 HEXADECIMAL DUMPING & SELF-TESTING
4-1 Hexadecimal dumping...............................................................
4-2
4-2 Self-Testing………………………………................................
4-2
CHAPTER 5 SOFTWARE CONFIGURATION
5-1 Ethernet Interface Card Setting..................................................
5-2
5-2 Printer Driver Setting……………………….............................
5-4

Contents
CHAPTER 6 COMMAND LIST
6-1 Standard Command List.............................................................
6-2
6-2 Two-Dimensional Bar Code Command Details.........................
6-4
6-3 Kanji Control Command Details……........................................
6-5
6-4 Standard Command Details…………………............................
6-6
CHAPTER 7 LANGUAGES
7-1 Ank Codes……………..............................................................
7-2
7-2 International Characters………………………..........................
7-5
7-3 Japanese Language Codes (Shift-JIS Codes)…….....................
7-6
7-4 Taiwanese Language Codes…………………...........................
7-14
7-5 Simplified Chinese Language Codes……………......................
7-6 Korean Language Codes……………………………………….
7-29
7-41

Page:1-1
INTRODUCTION
This chapter gives you the information for MP-1060. It also outlines
the system specifications.
Sections include:
About This Manual
System Specifications
Safety Precautions
Experienced users can jump to chapter 2 on page 2-1 for a quick
start.
CHAPTER
1

Chapter 1 Introduction
Page: 1-2
MP-1060 USER  S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our MP-1060 Thermal Receipt Printer System. The
MP-1060 is an updated system designed to be comparable with the highest
performance of Point-of-Sale platforms. The MP-1060 provides faster
processing speed, greater flexibility and can handle more commands than ever.
This manual is designed to assist you how to install and set up the whole system.
It contains five chapters. The user can refer the user’s manual for configuration
according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this printer board. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Parts and Basic Operation
Chapter 3 Install and Set Up
Chapter 4 Hexadecimal Dumping & Self-Test
Chapter 5 Software Configuration
This chapter indicates you how to set up the printer system through the software
utility.

Chapter 1 Introduction
MP-1060 USER  S MANUAL
Page: 1-3
Catchphrase:
1-2. SYSTEM SPECIFICATION
Features:
200mm high speed printing
Vertical and horizontal stand position capable
Built-in multi-language codepage includes Chinese, Japanese and
Korean characters
Support digital LOGO printing saved in FLASH ROM
Modularized design of printer head.
Multiple interface for USB/Serial and Ethernet Port
Auto paper cutter for full cut and partial cut available
Paper-near-end detector sensor and LED/Buzzer warring indicator.
EPSON command and other emulation
1D/2D barcode printing supported
Easy to set and high volume capacity of paper
Spectacular value-add accessories
OPOS driver supported

Chapter 1 Introduction
Page: 1-4
MP-1060 USER  S MANUAL
1-3. GENERAL SPECIFICATIONS
General
Print method
Thermal Line Printing
Printing width
72mm
Paper width
80mm
Printable dot No.
576 dots
Printing speed
Up to 200 mm/sec
Resolution
8 dot/mm
Sensors
Paper end, Cover Open,
Paper-near-end(Optional)
Cutter
Auto Cutter (Full/Partial)
Tear bar
Paper
Type
Receipt Thermal paper
Thickness
0.06mm~0.09mm
Roll diameter
Max. 80.0mm
Reliability
Printing head
100 km
MCBF
60 million lines
Auto cutter
1.5 million cuts
Performance
Interface
USB(Virtual COM)/Serial,
Ethernet(Optional)
Receive Buffer
4KB
Logo size
64K
Software
Emulation -
ESC/POS CMD compatible
Driver
WinXP/Win7/Win8/
-32bits & 64bits/OPOS
Physical
Dimensions
142mm x 127mm x 154mm
Weight
980g (w/o paper roll)
Cash drawer
1x 6pin RJ-11 connecter
Power supply
External 24v Adaptor

Chapter 1 Introduction
MP-1060 USER  S MANUAL
Page: 1-5
Language
Character Sets
Alphanumeric Characters: 95
Extended Characters: 128 x 8
Page (Blank x 1 Page)
International Characters: 32
Code Page
CP-437, Katakana character set,
CP-850, CP-852, CP-860, CP-863,
CP-865, WPC-1252
Compound
Character
Traditional Chinese, Simple
Chinese, Japanese, Korean
Character Size
Font A: 12 x 24 (default)
Font B: 9 x 17
Font C: 24 x 24
No. char per line
Font A: 36 C/L
Font B: 48 C/L
Font C: 18 C/L
Barcode
1D
UPC-A, UPC-E, JAN8(EAN8),
JAN13(EAN13), CODE39,
ITF(Interleaved 2 of 5),
CODABAR(NW-7), CODE93,
CODE128,
2D
QR Code
Environment
Operating Temp
-10 to 50°C (35 °C In case of
Printing-rate over 10%)
Storage Temp
-30 to 60°C
Operating Temp
10 to 90% RH
Storage Temp
10 to 90% RH expect for paper
Accessories
2” Paper Guide, Splash Proof
Cover, Wall-mount Kit, Cable
Cover, Paper-near-end Sensor Kit,
Melody Box, Interface Cables,
International Power Cords
Certification
CE, FCC

Chapter 1 Introduction
Page: 1-6
MP-1060 USER  S MANUAL
1-4. SAFETY PRECAUTIONS
Following messages are safety reminders on how to protect your systems from
damages. And thus, helps you lengthen the life cycle of the system.
1. Check the Line Voltage
a. The operating voltage for the power supply should cover the range of
100VAC-240V AC, otherwise the system may be damaged.
2. Environmental Conditions
a. Avoid extremely hot or cold places to install MP-1060.
b. Avoid exposure to sunlight for a long period of time (for example in a closed
car in summer time. Also avoid the system from any heating device.). Or do not
use MP-1060 when it‘s been left outdoors in a cold winter day.
c. Bear in mind that the operating ambient temperature is from 5C up to +35C.
d. Avoid moving the system rapidly from a hot place to a cold place or vice
versa because condensation may come from inside of the system.
e. Place MP-1060 against strong vibrations, which may cause hard disk failure.
f. Do not place the system too close to any radioactive device. Radio-active
device may cause interference.
3. Good Care
a. When the outside of the case is stained, remove the stain with neutral
washing agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the system.
c. If heavy stains are present, moisten a cloth with diluted neutral washing agent
or with alcohol and then wipe thoroughly with a dry cloth.
d. If dust has been accumulated on the outside, remove it by using a special
made vacuum cleaner for computers.

Page 2-1
PARTS AND BASIC
OPERATION
CHAPTER
2
Helpful information describes the parts and operation of MP-1060.
Sections include:
Unpacking
Part Structure
Connectors

Chapter 2 Parts and Operations
Page: 2-2 MP-1060 USER
′
S MANUAL
2-1. UNPACKING
2-1-1 Main parts
 Printer (body) × 1
 User’s CD-ROM × 1  External power supply unit × 1

Chapter 2 Hardware Configuration
MP-1060 USER
′
S MANUAL
2-1-2 Options
Cable cover S
plash proof cover
2” Paper guide 2”
/3
 Wall mount kits Hanging bracket set
Chapter 2 Hardware Configuration
Page: 2-3
plash proof cover
/3
” 10M Test Roll paper

Chapter 2 Parts and Operations
Page: 2-4 MP-1060 USER
′
S MANUAL

External Interface Cables (USB/Serial/LAN)

Chapter 2 Hardware Configuration
MP-1060 USER
′
S MANUAL Page: 2-5
2-2 Part Structure
2-2-1 Main body

Chapter 2 Parts and Operations
Page: 2-6 MP-1060 USER
′
S MANUAL
2-2-2 Control Panel
POWER (Blue)
Lights when the power supply is on.
Goes out when the power supply is turned off.
ERROR (Red)
Lights when an error occurs.
Goes out during regular operation.
PAPER (Yellow)
Lights when there is no more roll paper.
Goes out when there is a sufficient amount of roll paper remaining.
Flashes when paper near end sensor is enabled and there is little remaining.

Chapter 2 Hardware Configuration
MP-1060 USER
′
S MANUAL Page: 2-7
2-2-3 Buttons
FEED button
Pressing this button once feeds the roll paper by one line. Holding this button
down and feeds the roll paper continuously.
2-2-4 Power Switch
The power switch is located at the bottom right front of the printer.
Turn the printer on or off. The marks on the switch (0 = on / 1 = off) indicate
the printer switch position.
CAUTION:
Before turning on the printer be sure to check that the AC adapter is connected
to the power supply.

Chapter 2 Parts and Operations
Page: 2-8 MP-1060 USER
′
S MANUAL
2-3 Connectors
All cables are connected to the connector panel on the lower rear of the printer.
Drawer kick-out connector for connecting the cash drawer
Power supply connector for connecting the power supply unit
Interface connector to connect the printer to the host computer interface
(serial/USB/LAN)

Chapter 2 Hardware Configuration
MP-1060 USER
′
S MANUAL Page: 2-9
2-4 Installing and Replacing Roll Paper
CAUTION:
Be sure to use roll paper that meets printer specifications. Do not use roll
paper whose trailing end is glued to the roll paper core.
Installing Roll Paper
1. Make sure the host has not sent a printing command to the printer, and
press the cover open button to open the printer cover.

Chapter 2 Parts and Operations
Page: 2-10 MP-1060 USER
′
S MANUAL
2. Load the roll paper.
Horizontal position:
Vertical position:
CAUTION:
When loading the roll paper, pay attention to the direction that the roll paper is
fed out of the printer.
3. Pull out the roll paper toward you, and then close the printer cover.