Protocol Galileo 6182-5U User manual

Galileo
RADIO CONTROLLED
QUAD-COPTER
FEATURING:
1. Four-Rotor design allows great speed and maneuverability for both Indoor and Outdoor use.
2. Built-in 6-axis Gyro ensures excellent stability.
3. Modular design for increased ease of maintenance.
4. 360-degree 3-dimensional stunt and tumbling function
5. Photo/Video
The materials and specifications stated in this instruction manual are for reference only.
TM

Canopy (Top)
Canopy(Bottom)
Rotor
Rotor Guard
Camera
Landing Skid
SCHEMATIC
GALILEO
RC VIDEO DRONE
Thank you for your purchase of Protocol’s Galileo. You are about to
experience the best of what remote control flight has to offer. We strongly
recommend that you take the time to read this manual thoroughly. It contains
many tips and instructions on how to get the most out of this aircraft and
maintain it for a long life.
As with any aircraft, this is a precision flying machine. Treat it well and enjoy all
the fun it has to offer, flight after flight.
SAFETY AND PRECAUTIONS
1. Keep small parts out of reach of children to avoid accidents.
2. The quad-copter is powerful and fast; accelerate gently to avoid damage and accidents.
3. After flying, disconnect the battery.
4. Keep the battery away from heat sources and / or fire.
5. Keep the quad-copter at a distance of at least 2 meters from yourself, others, and obstacles
to prevent damage.
6. Children should operate the quad-copter only under adult supervision.
7. The remote controller batteries can not be recharged. Do not mix new batteries with old batteries
or mix batteries of different types.
8. Always turn off both the transmitter and quad-copter when not in use.
9. Never attempt to short-circuit the battery terminals or the quad-copter.
1

01. Fine-tuning: Side-to-side Strafing [defaults to center on start-up]
02. Fine-tuning: Forward/Backward [defaults to center on start-up]
03. Fine-tuning: Turn Left/Right [defaults to center on start-up]
04. Fine-tuning: Throttle [defaults to center on start-up]
05. Throttle [defaults to zero on start-up]
06. Directional Display [defaults to center on start-up]
07. Lateral Movement to Right
08. Rearward Movement
09. Lateral movement to Left
10. Right rotational movement [defaults to zero on start-up]
11. Left rotational movement [defaults to zero on start-up]
12. High Speed Mode Active
13. Low Speed Mode Active
14. Controller Battery Level Indicator
15. Flight Mode 1 Active (Default); To change to Mode 2, press and hold Mode Switch to the right
while turning on the transmitter.
16. Remote control signal strength
17. Indicates positive communication lock with the Galileo
LCD Display
Antenna
Indicator Light
3D Stunt
Right function lever
(4-way directional)
Fine-tune
Forward/Backward
Mode Switch
Fine-tune
Strafe left/right
(Mode 1)
High/Low Speed
mode selector
Power Switch
Left function lever
Throttle
Photo/Video
Fine-tune
Turn left/right
(Mode 1)
1. Install batteries carefully.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.
Remote Control
REMOTE CONTROL KEYPAD AND LCD MANUAL
2
Fine-tune
Strafe left/right
(Mode 2) Fine-tune left/right
(Mode 2)
Remove battery cover from R/C unit, insert 4 ‘AA’ batteries, noting polarity indicators.
Replace battery cover.

FLYING THE QUADCOPTER
Step 1: Open the battery
cover and insert the
battery into the power port.
Step 2: Close the battery
cover and turn on the
quad-copter.
Step 4: Push the throttle lever to the highest position, and
then pull it back to the lowest position. There will be two
beeps from the transmitter. This shows that the quad-
copter has synced with the remote.
Tips: When syncing your quad-copter keep it
in a horizontal position for stable flight.
1. If the Galileo and the remote do not sync after following the checklist, reverse steps 1 and
3 of the process. Turn the remote and Galileo off. Then, turn on the remote first and then
the Galileo. Follow with Step 4.
2. Turn on the controller; if, after 30 seconds, it has not recognized the drone, turn off the
controller to retry synchronization.
3. If quad-copter’s LED blinks slowly, it means that it has not recognized the controller; please
restart pre-flight procedure.
4. If the Galileo is unsteady in flight, it may not have been able to calibrate horizontally. Power
down both vehicle and remote and restart pre-flight procedure.
Tips: When syncing your quad-copter keep it in a horizontal position for stable flight.
NOTE
3
Step 3: Push the ON/OFF
power switch up.

CHARGING THE QUAD-COPTER BATTERY
1. Push the on/off switch of the
quad-copter to OFF and open
the battery cover.
2. Pull out the battery wire
from the power port.
3. Connect the charging
adapter to the battery wire.
4. Plug the adapter into an AC charger
and charge. The green charging light
will turn on while charging and will go
off once charged.
5. Reconnect the battery wire to the power port
and close the battery cover.
Charging time: approximately 200 minutes ---
Flying time: approximately 7 minutes
1. When charging, place product on a dry, well-ventilated surface and keep away from heat
sources.
2. Always use adult supervision while charging.
3. As battery temperature is high immediately after flight, charge after cooling down for
higher efficiency.
4. Do not strike or subject battery to hard impacts or sharp surfaces.
5. Do not use any other charger than that which is supplied with this item.
6. Do not use or leave battery near a heat source such as fire or space heater; exposure to
heat may result in reduced performance or in some cases dangerous conditions.
7. If battery is left in charging state for an extended period of time after being fully charged,
the battery may automatically discharge.
8. Never leave the battery unattended during charging.
CAUTION WHEN CHARGING
4

1. Do not immerse or submerge battery in water; store in a cool, dry location.
2. In order to increase battery longevity, avoid repeat charging and excessive discharging.
3. Charge battery to approximately 55% capacity prior to long-term storage.
4. If battery sees no use for extended periods of time, it is recommended that battery voltage
is kept above 3V. Check monthly and recharge as needed.
5. Do not disassemble battery.
BATTERY REPAIR & MAINTENANCE
1. Install the landing skids to the bottom of the quad-copter (Figure 1).
2. Install the blade protection frame to every corner and tighten the screws (Figure 2).
3. Installing the blades (Fig. 3):
a. Remove the lockstitch from the axis pipe by twisting it in the direction of the arrows on
the lockstitch until you hear a click. You may want to use a tissue or a cloth as you twist.
b. Pull the lockstitch down to expose the locking bar. Slide the bar out of the axis pipe and
slide the lockstitch off the axis pipe.
c. Slide the blade onto the axis pipe with the metal side up. Push the blade all the way
down so it fits snugly over the plastic part of the axis pipe.
d. Slide the lockstitch down on the axis pipe.
e. Align the opening on the lockstitch with the hole in the axis pipe. Insert the locking bar
into the axis pipe and turn the lockstitch until you hear another click. The blade is now
installed.
f. Slide the silver cap over the axis pipe until it is snug.
NOTE: If the quad-copter crashes, double check to make sure the blade protection frame is
not loose. If it is, re-tighten before flying.
NOTE: If you prefer to not install blade guards, fillers are included to place in the slots instead.
INSTALL LANDING SKIDS, BLADES, & BLADE GUARDS
FIG. 1
FIG. 2
5
FIG. 3

HIGH-LOW SPEED MODES
OPERATION (MODE 1)
HOVER UP AND DOWN FORWARD AND BACKWARD
Push the throttle up or down, the quad-
copter flies upward or downward.
Push the direction lever up or down, the
quad-copter flies forward or backward.
TURNING LEFT AND RIGHT SIDEWAYS FLIGHT
Pull the throttle left or right, the quad-
copter turns to the left or right.
Pull the direction left to the left or right,
the quad-copter banks to the left or right.
FORWARD/BACKWARD TRIM
When the quad-copter veers
forward/backward unintentionally,
you can correct it by pressing
the trim button in the opposite
direction until it evens out.
When the quad-copter veers to
the left or right side unintentionally,
you can correct it by pressing the
trim button in the opposite direction
until it evens out.
When the quad-copter keeps
spinning left or right unintentionally,
you can correct it by pressing the
trim button in the opposite direction
until it evens out.
TRIM ADJUSTMENT
SIDEWAYS TRIM LEFT/RIGHT TRIM
6
The Galileo features 2 speed modes. Low speed is for beginners and high speed is for
advanced users.
Press the speed mode button to adjust speed.
High/Low Speed
mode selector

7
OPERATION (MODE 2)
HOVER UP AND DOWN FORWARD AND BACKWARD
Push the throttle up or down, the quad-
copter flies upward or downward.
Push the direction lever up or down, the
quad-copter flies forward or backward.
TURNING LEFT AND RIGHT SIDEWAYS FLIGHT
Pull the direction stick left or right, the
quad-copter turns to the left or right.
Pull the throttle left to the left or right,
the quad-copter banks to the left or right.
FORWARD/BACKWARD TRIM
When the quad-copter veers
forward/backward unintentionally,
you can correct it by pressing
the trim button in the opposite
direction until it evens out.
When the quad-copter veers to
the left or right side unintentionally,
you can correct it by pressing the
trim button in the opposite direction
until it evens out.
When the quad-copter keeps
spinning left or right unintentionally,
you can correct it by pressing the
trim button in the opposite direction
until it evens out.
TRIM ADJUSTMENT
SIDEWAYS TRIM LEFT/RIGHT TRIM

TROUBLESHOOTING
Symptom Possible Cause Potential Solution
Galileo
does not
respond
Response to
control inputs
intermittent
or erratic
1. Communication between controller and
aircraft was not synchronized during set up
2. Battery power depleted on aircraft,
controller or both.
1. To synchronize, turn on controller, then
turn on aircraft and place it on level
ground. Move throttle stick all the way
forward, then all the way back.
2. Charge aircraft and/or replace
batteries in controller.
1. Controller battery power nearly depleted. 1. Replace batteries in controller.
Galileo
will not hover
or strafe
correctly
1. The aircraft was not on level ground
during synchronization.
2. Trim settings are incorrect.
1. Re-synchronize aircraft and controller.
2. Reset the trim buttons on the controller
and re-trim flight controls.
Once you are familiar with the basics of quad-copter flight, you can try some advanced maneuvers! At a
height of at least 10 feet, press the STUNT button [on controller’s right side] then move the right stick in
whichever direction desired to perform a 360-degree flip in that direction.
TIPS ON 3D STUNT & TUMBLING OPERATION
Restart function:
In case of flight disorder, restore factory default settings by the following methods:
1. Press the power switch to turn on the transmitter.
2. Press the power switch to turn on the quad-copter.
3. When the quad-copter indicator flashes slowly, push the throttle lever to the highest
position, and then pull it back to the lowest position. The quad-copter indicator will change
from slow flashing to steady mode.
4. Place the quad-copter on a horizontal position, then push both left and right lever on the
transmitter to the lowest right corners for 2-3 seconds. The indicator on the quad-copter will
change from normal light to quick flashing light. After 2-3 seconds the indicator will change
back to the normal light. This means the quad-copter has restarted/reset successfully.
8

If the camera is not pre-installed:
1. Push the camera into the hold underneath the drone.
2. Plug the camera into the drone.
NOTE: Do not unplug or plug in the camera while the drone is on.
CAMERA
PHOTOGRAPHY/VIDEO INSTRUCTIONS
9
1. The memory card comes pre-inserted into the camera.
2. Turn the quad-copter on. The lights of the camera will flash and then become steady
green. If there is a red indicator on the camera, it means the memory card is not in the
camera. Insert the memory card and the red indicator will turn to green.
Shooting Video/Photo:
1. Turn on the transmitter and pull the throttle up and down to connect the quad-copter
and transmitter.
2. Photo: Push the Photo/Video button up and the camera will take a photo. The red
indicator will flash once and the remote will beep as it’s taking the picture.
3. Video: Push the Photo/Video button down and the camera will begin to record. The red
indicator will flash repeatedly and the remote will beep twice while recording video. Push
the Photo/Video button down again and the camera will stop recording.
4. Remove the memory card by pushing it in until it springs out of the camera.
5. Insert the memory card into the card reader. (Fig. 1)
6. Place the card reader into the USB port of your computer. The USB will come up on the
removable drive.
7. Open the drive and then open the Video or Photo folders to access the .AVI or JPEG
files.
8. .AVI movies can be played in several different formats including Quicktime, Windows
Media Player, and RealPlayer.
WARNING: Never remove the card from
the video camera while the helicopter is
turned on.
NOTES:
- All files on the card can be removed
or erased without compromising the
video camera
Fig. 1

Thank you for your purchase of Protocol’s Galileo RC Video Drone. We know that accidents can
sometimes happen and that is why we offer spare parts kits on our website: ProtocolNY.com.
10