PROTRON PLTV-3250 User manual

MENU CH CH VOL VOL ENTER SOURCE POWER
MTS MENU
DISPLAY TV SOURCE
LIST SLEEP PICTURE SOUND
FAV. C.C. V-CHIP EPG
MUTE
ASPECT
VOL
VOL
CH
CH
Accessories
PLTV-3250
32" Liquid Crystal Display
User’s Manual
VGA Cable
PC Audio Cable RCA Cables
Component Video
Cables
HDMI D-SUB
ACIN
AV1 IN
AUDIO1
SC-ART 1
SC-ART 2
S-VIDEOIN
S-VIDEO
PC
AUDIOIN
VIDEO1
ANT
Remote
AAA Batteries
User’s Manual
Power Cord
Start Here
Easy Setup Instructions
Unpacking the Display and Accessories
1. Remove the contents of the box and place the display in its
intended location.
Accessories
Box
2. Plug in the display and turn it on.
Connecting Component Video Devices
(Ex: Progressive Scan DVD Player, HDTV Receiver)
1. Using three RCA cables, connect the three component video
outputs (Y, Pb, and Pr) to the corresponding jacks in one of the
two component video blocks on the display.
2. Using two other RCA cables, connect the right (red) and left
(white) audio outputs on the source to the corresponding jacks
in the same component video block used above.
R
L
Connecting a Digital TV (HDTV) Antenna
1. Connect a coaxial cable between the ATSC jack and TV signal
source.
Connecting HDMI Devices
1. Using an HDMI cable, connect the HDMI device to the HDMI
input on the bottom of the display.
HDMI D-SUB
AV IN
AUDIO
SC-ART 1
S-VIDEO IN
S-VIDEO
PC
AUDIO IN
VIDEO
Connecting an Analog TV Signal
(Ex: Cable Box, Satellite Receiver, Antenna)
1. Connect a coaxial cable between the NTSC jack and TV signal
source.
Note: If you would like to be able to record the TV signal,
connect the TV signal source to the recording device, then
connect the recording device to the display.
Connecting Composite Video Devices
(Ex: VCR, DVD Player)
1. Using an RCA cable, connect the composite video output
(yellow) on the source device to the corresponding jack in one
of the two composite video blocks: AV 1 IN on the bottom of
the display or AV 2 IN on the right side of the display.
2. Using two RCA cables, connect the right (red) and left (white)
audio outputs on the source to the corresponding jacks in the
same composite video block used above.
HDMI D-SUB RS-232
AV 1 IN
AUDIO 1
SC-ART 1
S-VIDEO IN
S-VIDEO
PC
AUDIO IN
VIDEO 1
Vertical fold
Vertical fold
EZPLTV3250-1.indd 1 7/17/2006 7:58:36 PM

HDMI D-SUB
ACIN
AV1IN
AUDIO1
SC-ART1
SC-ART2
S-VIDEOIN
S-VIDEO
PC
AUDIOIN
VIDEO1
ANT
Installing Batteries in the Remote Control
1. Remove the plastic battery compartment cover from the rear of
the remote.
2. Insert two AAA batteries. Be sure to orient the batteries as
indicated in the compartment.
3. Replace the cover.
MTS MENU
DISPLAY TV SOURCE
LIST SLEEP PICTURE SOUND
FAV. C.C. V-CHIP EPG
MUTE
ASPECT
VOL
VOL
CH
CH
Setting up Digital Television Channels
1. Ensure the display is on and the signal source is set to DTV.
2. Press to bring up the On-Screen Display (OSD).
MTS MENU
DISPLAY TV SOURCE
LIST SLEEP PICTURE SOUND
FAV. C.C. V-CHIP EPG
MUTE
ASPECT
VOL
VOL
CH
CH
3. Press until the Setup menu shows.
Main Menu
Setup
OSD Language
Time Zone
All Reset
System Info MDDO-052 Apr 25 2006
No
Atlantic
English
4. Press until Time Zone is highlighted and then press
until the correct time zone is selected and press .
5. Press until the Channel menu shows.
Main Menu
Channel
Auto Program
Manual Program
Channel List
Favorite List
SNR
CH 002
Digital
6. Press until Auto Program is highlighted and then press
twice to begin scanning for available television channels.
For more information, refer to the User’s Manual.
PLTV-3250
32" Liquid Crystal Display
User’s Manual
Operating the Display
1. On the remote, press to turn the display on.
MTS MENU
DISPLAY TV SOURCE
LIST SLEEP PICTURE SOUND
FAV. C.C. V-CHIP EPG
MUTE
ASPECT
VOL
VOL
CH
CH
2. Press until the desired signal source is selected (the name
of the currently selected signal source will display at the top
right of the screen).
3. If the source is set to “TV” or “DTV”, use to change the
channel.
MTS MENU
DISPLAY TV SOURCE
LIST SLEEP PICTURE SOUND
FAV. C.C. V-CHIP EPG
MUTE
ASPECT
VOL
VOL
CH
CH
4. Use to adjust the volume.
Connecting a PC
1. Set the video resolution on the computer to 1280 × 1024 or
less.
2. Connect a VGA cable between the VGA output on the
computer and the D-SUB input on the display.
HDMI D-SUB
AV IN
AUDIO
SC-ART 1
S-VIDEO IN
S-VIDEO
PC
AUDIO IN
VIDEO
3. (OPTIONAL) Using a 1/8” stereo audio cable, connect the
computer’s audio output (LINE OUT) to the audio input on the
bottom of the display (PC AUDIO IN).
HDMI D-SUB
AV 1 IN
AUDIO 1
SC-ART 1
S-VIDEO IN
S-VIDEO
PC
AUDIO IN
VIDEO 1
Setting up Analog Television Channels
1. Ensure the display is on and the signal source is set to TV.
2. Press to bring up the On-Screen Display (OSD).
3. Press until the TV menu shows and press to enter it.
Image Auto Scan
Audio Channel System
TV Program Editor
PC Fine Tune
Setup
6. Press until Channel System is highlighted, then press
to select it.
7. Press until the appropriate system is highlighted, then
press to select it.
Select Air if you are using an antenna.
Select one of the Cable options if you are connecting directly
to a cable TV wall outlet. Contact your cable service provider to
find out which system is in use in your area. Cable or Cable-IRC
will work with most systems.
8. Press to return to the TV menu.
9. Press until Auto Scan is highlighted and then press
to select it. The display will automatically scan all television
channels for those with a strong signal.
© 2006 Protron Digital Corporation EZPLTV3250-1
Vertical fold
Vertical fold
EZPLTV3250-1.indd 2 7/17/2006 7:58:41 PM