Providence RX-L1 User manual

■Controls and Connections
①L1 (Loop 1 Switch)urns Loop 1 ON or OFF. When the loop is ON the corresponding indicator will
light and the signal will be routed through the effect unit connected to the
SND-1 and R N-1 jacks.
②L2 (Loop 2 Switch)urns Loop 2 ON or OFF. When the loop is ON the corresponding indicator will
light and the signal will be routed through the effect unit connected to the
SND-2 and R N-2 jacks.
③L3 (Loop 3 Switch)urns Loop 3 ON or OFF. When the loop is ON the corresponding indicator will
light and the signal will be routed through the effect unit connected to the
SND-3 and R N-3 jacks.
④DC9V OVERLOAD (DC9V Overload Indicator)his warning indicator will light when the total current load on the three DC9V
outputs exceeds the maximum supply capacity of 180 milliamps..
⑤IN (Input)he output from the guitar, bass, or other instrument used is connected to this
input jack.
⑥SND-1〜SND-3 (Send 1〜Send 3)hese are the send jacks for the effect loops. Each send jack should be con-
nected to the input jack of the corresponding effect unit.
⑦RTN-1〜RTN-3 (Return 1〜Return 3)hese are the return jacks from corresponding effect loops. he output from
each effect unit should be connected to the corresponding return jack.
⑧OUT (Output)his is the final output from the effect chain. he OU jack should be connect-
ed to the input of the following amplifier or processing device.
⑨DC9V OUT (DC9V Output)DC9V output connectors. hree DC9V outputs with a total supply capacity of
180 milliamps are provided.
⑩POWER (DC9V Input)he AC adaptor used to power the unit should be connected here.
■About the RX Series DC9V Outputs
he RX series routing boxes include three DC9V outputs that can be used to
power compatible effect units. he total current supply capacity of the three
outputs is 180 milliamps. If the 180 milliamp supply capacity is exceeded the
DC9V OVERLOAD indicator will light to warn that a voltage drop and overheat-
ing may occur. Do not continue to use the device if the OVERLOAD indicator
lights. Refer to the manuals that came with the effect units being used for infor-
mation on their power consumption.
Each DC9V output also includes an independent filter that prevents power line
noise from entering the signal path. he main power supply circuit additionally
features a short protection circuit that prevents damage to the power supply if
the DC9V output is accidentally shorted.
■Connection example
■Functions
The RX-L1 provides three series-connected e ect loops. E ect units connected to the e ect loops can be selected and combined as required via
ootswitches while maintaining optimum signal quality at all times.
■Specifications
• Power Consumption: DC9V, approx. 30 mA (all LEDs ON)
• Dimensions (W x D x H): 180 x 60 x 32 front/40 rear mm, not including
protrusions
• Weight: approx. 450 grams
■Precautions
• he footswitches will operate and the audio signal will be routed
accordingly even if the power supply (AC adaptor) is not connected, but
the LED indicators will not light and no power will be supplied to the
DC9V outputs.
• Do not insert/remove plugs into/from the unit’s input or output jacks
while connected to an amplifier or speaker system that is powered ON.
Doing so can cause noise spikes that might damage the speakers.
• If the unit malfunctions, cease operation immediately and contact the
dealer from which the unit was purchased or the manufacturer.
*Specification and appearance are subject to change without notice.
PPD0837-02Rev1.1OWNER’S MANUAL
Thank you or choosing Providence. In order to take ull advantage o the product’s eatures and per ormance, please read this
manual thoroughly and keep it in a sa e place or uture re erence.
■Features
• Compact dimensions (180 mm wide x 60 mm deep)
• 70 mm ootswitch spacing or easy operation
• Three DC9V outputs (180 mA max.)
• DC9V output overload warning indicator
• Bright indicator LEDs with high-visibility lenses
• E ect loop switches eature Single Contact True Bypass cir-
cuitry ensuring that the signal only passes through one contact
per switch in bypass mode or maximum reliability and sound
quality.

Rev1.1■Controls and Connections
①L1 (Loop 1 Switch)urns Loop 1 ON or OFF. When the loop is ON the corresponding indicator will
light and the signal will be routed through the effect unit connected to the
SND-1 and R N-1 jacks.
②L2 (Loop 2 Switch)urns Loop 2 ON or OFF. When the loop is ON the corresponding indicator will
light and the signal will be routed through the effect unit connected to the
SND-2 and R N-2 jacks.
③A/B (A/B Switch)Routes the output signal to either the A or B output. he indicator lights when
the A output is selected. When the indicator is not lit the B output is selected.
④DC9V OVERLOAD (DC9V Overload Indicator)his warning indicator will light when the total current load on the three DC9V
outputs exceeds the maximum supply capacity of 180 milliamps..
⑤IN (Input)he output from the guitar, bass, or other instrument used is connected to this
input jack.
⑥SND-1〜SND-2 (Send 1〜Send 2)hese are the send jacks for the effect loops. Each send jack should be con-
nected to the input jack of the corresponding effect unit.
⑦RTN-1〜RTN-2 (Return 1〜Return 2)hese are the return jacks from corresponding effect loops. he output from
each effect unit should be connected to the corresponding return jack.
⑧A-OUT (A Output)he signal is output via this jack when the indicator above the A/B Switch is lit.
his output jack should be connected to the input of the following amplifier or
other device.
⑨B-OUT (B Output)he signal is output via this jack when the indicator above the A/B Switch is lit.
his output jack should be connected to the input of the following amplifier or
other device.
⑩DC9V OUT (DC9V Output)DC9V output connectors. hree DC9V outputs with a total supply capacity of
180 milliamps are provided.
⑪POWER (DC9V Input)he AC adaptor used to power the unit should be connected here.
■About the RX Series DC9V Outputs
he RX series routing boxes include three DC9V outputs that can be used to
power compatible effect units. he total current supply capacity of the three
outputs is 180 milliamps. If the 180 milliamp supply capacity is exceeded the
DC9V OVERLOAD indicator will light to warn that a voltage drop and overheat-
ing may occur. Do not continue to use the device if the OVERLOAD indicator
lights. Refer to the manuals that came with the effect units being used for infor-
mation on their power consumption.
Each DC9V output also includes an independent filter that prevents power line
noise from entering the signal path. he main power supply circuit additionally
features a short protection circuit that prevents damage to the power supply if
the DC9V output is accidentally shorted.
■Functions
The RX-S1 provides two series-connected e ect loops. E ect units connected to the e ect loops can be selected and combined as required via
ootswitches while maintaining optimum signal quality at all times. An A/B output select circuit is provided ollowing the e ect loops, allowing the
device’s output to be switched between two di erent ampli iers, an ampli ier and a tuner, or simply muted as required.
OWNER’S MANUAL
Thank you or choosing Providence. In order to take ull advantage o the product’s eatures and per ormance, please read this
manual thoroughly and keep it in a sa e place or uture re erence.
■Features
• Compact dimensions (180 mm wide x 60 mm deep)
• 70 mm ootswitch spacing or easy operation
• Three DC9V outputs (180 mA max.)
• DC9V output overload warning indicator
• Bright indicator LEDs with high-visibility lenses
• E ect loop switches eature Single Contact True Bypass cir-
cuitry ensuring that the signal only passes through one contact
per switch in bypass mode or maximum reliability and sound
quality.
■Connection example
■Specifications
• Power Consumption: DC9V, approx. 30 mA (all LEDs ON)
• Dimensions (W x D x H): 180 x 60 x 32 front/40 rear mm, not including
protrusions
• Weight: approx. 450 grams
■Precautions
• he footswitches will operate and the audio signal will be routed
accordingly even if the power supply (AC adaptor) is not connected, but
the LED indicators will not light and no power will be supplied to the
DC9V outputs.
• Do not insert/remove plugs into/from the unit’s input or output jacks
while connected to an amplifier or speaker system that is powered ON.
Doing so can cause noise spikes that might damage the speakers.
• If the unit malfunctions, cease operation immediately and contact the
dealer from which the unit was purchased or the manufacturer.
*Specification and appearance are subject to change without notice.
PPD0837-02
Table of contents
Other Providence Network Router manuals