Provision ISR PoES-16300GCL+2SFP User manual

User Manual
Color LCD PoE Switch
●PoES-16300GCL+2SFP
●PoES-24380GCL+2SFP
●PoES-16300CL+2G+2SFP
●PoES-24380CL+2G+2SFP

Page | 2 COLORLCDPOESWITCHUSERMANUAL



Notes

 Beforeoperatingtheswitch,westronglyadviseuserstoreadthismanualandkeepitfor
lateruse.
 Pleaseusethesuppliedpowercord.
 Avoidincorrectoperation,shock,vibrationorheavypressingwhichcancausedamageto
theswitch.
 Donotusecorrosivedetergenttocleanthebodyoftheswitch.Ifnecessary,pleaseusea
softdryclothtowipedirt;forhardcontamination,useneutraldetergent.Anycleanserfor
high‐gradefurnitureisapplicable.
 Donotoperatetheswitchinextremetemperaturesorextremehumidityconditions.
 Keepawayfromheatsourcessuchasradiators,heatregisters,stove,etc.
 Theinstructionsinthismanualcouldbeoutdated;ifyouneedanyclarificationsyoucan
contactanauthorizedPROVISION‐ISRtechnician.PROVISION‐ISRreservestherighttoadd
changestothismanualandpublishitonlineonourwebsite(www.provision‐isr.com):there
maybeinconsistencieswiththelatestversion.Thisappliestoanyandallsoftwareupgrades
andproductimprovements,interpretationandmodificationadded.Thesechangeswillbe
publishedinthelatestversionwithoutpriornotification.
 Allpicturesandexamplesusedinthemanualareforreferenceonly.


PackageContents

Checkthefollowingcontentsofyourpackage: 

 PoESwitch x1 

 User’sManual x1 

 PowerCord x1 

 Accessories(Rackmountears*2,RubberFeet*4,Bracketscrews*8) 

Ifanypartislostanddamaged,pleasecontactyourlocalagentimmediately.










Page | 3 COLORLCDPOESWITCHUSERMANUAL



TableofContents
1) Introduction................................................................................................................4
2) HardwareDescription .............................................................................................4
2.1)  FrontPanel: ........................................................................................................4
2.2) RearPanel.............................................................................................................5
3)  LCDFeatures: ...........................................................................................................6
3.1)  GeneralStatusIndicators: ................................................................................6
3.2)  GeneralWarnings: .............................................................................................6
3.3)  PortStatusWarnings: .......................................................................................7
3.4)  MenuandOperations: ......................................................................................7
3.4.1. SwitchMode:........................................................................................................7
3.4.2. PortBandwidthLimit:...........................................................................................8
3.4.3. PDType:................................................................................................................8
3.4.4. KeepAlive:............................................................................................................8
3.4.5. PSEPowerAdjust:.................................................................................................9
3.4.6. PSEPortPriority:..................................................................................................9
3.4.7. PSEPortCondition:.............................................................................................10
3.4.8. PoEPortPower:..................................................................................................10
3.4.9. LCDState:...........................................................................................................11
3.4.10.FanControl:........................................................................................................11
3.4.11.DefaultSettings:.................................................................................................11
3.4.12.About:.................................................................................................................12
4)  SwitchInstallation: ................................................................................................12
4.1)  DesktopInstallation: .......................................................................................12
4.2)  RackMountInstallation ..................................................................................13
4.3)  Turningontheswitch .....................................................................................14



Page | 4 COLORLCDPOESWITCHUSERMANUAL



1) Introduction

Thank you for choosingProvision‐ISR’s PoE Switch. The 16/24GE(PoE)+2G SFPLCD
DisplayPoE switchhave16(24)‐10/100/1000MbpsPoERJ45Portand2‐GigabitSFPSlot.Its
PoEportscanautomaticallydetectandsupply power withthose IEEE802.3af/atcompliant
PoweredDevices(PD).Theelectricalpoweristransmittedalongwithdatainonesinglecable
allowingyoutoexpandyournetworkwheretherearenopowerlinesoroutlets,whereyou
wishtofixdevicessuchasAP,IPCamerasorIPPhones,etc.
TheLCDcanbeusedtodisplaythePoEworkstatus,accuratemeasurementtotalload
andforeachportindependently.Thiscanhelptheinstallerandengineertoquicklydiscover
andsolvenetworkfailuresandimproveworkefficiencyandquality.

PortFeature
Model PoEPorts PoEPortsSpeed UplinkPorts UplinkPortsSpeed
PoES‐16300GCL+2SFP 16(1‐16) 10/100/1000Mbps 2SFP(17‐18) 10/100/1000Mbps
PoES‐24380GCL+2SFP 24(1‐24) 10/100/1000Mbps 2SFP(25‐26) 10/100/1000Mbps
PoES‐16300CL+2G+2SFP 16(1‐16) 10/100Mbps 2SFP+2RJ‐45
(17‐20)
10/100/1000Mbps
PoES‐24380CL+2G+2SFP 24(1‐24) 10/100Mbps 2SFP+2RJ‐45
(25‐28)
10/100/1000Mbps

2) HardwareDescription 

2.1) FrontPanel:

TheFrontPanelofthePoESwitchconsistsofEthernetPorts,LCDDisplay+controlsandLED
indicators.

Giga(10/100/1000MbpsSwitches)Frontpanelillustration.






8.4
01
W
‐‐‐M631M
ULP
02 ‐‐‐M921M
OLP
03 ‐‐‐M‐‐‐M
SCP04 125M‐‐‐M
2.2W05 ‐‐‐M‐‐‐M
23.706 W ‐‐‐M‐‐‐M
16.807 W ‐‐‐M‐‐‐M
13.408 W ‐‐‐M920M
18.909 W 856M856M
‐‐‐‐10 W 238M238M
11 OFF ‐‐‐M‐‐‐M
23.312 W 323M323M
5.813 W 983M983M
7.314 W 223M223M
GeneralInformation
MenuControls
LEDIndicators PoEDownlinkPorts SFPUplink
Ports
LCD Monitor

Page | 5 COLORLCDPOESWITCHUSERMANUAL




10/100MbpsSwitchesFrontpanelillustration.






LEDindicators 

LED Color Function

PWR

Green
O
ff
:Switchisoff/Nopower supply.
Light:Theswitchison.





LNK/ACT


Orange
O
ff
:Nodevice isconnected tothe correspondingport.
Light:Indicatesthelinkthroughthatportissuccessfullyestablishedat
10/100Mbps.
Blink:IndicatesthattheSwitchisactivelysendingor
receivingdataoverthatport.


Green
O
ff
:Nodevice isconnected tothe correspondingport.
Light:Indicatesthelinkthroughthatportissuccessfullyestablishedat
1000Mbps.
Blink:IndicatesthattheSwitchisactivelysendingor
receivingdataoverthatport.


PoE


Orange
O
ff
:NoPoEpowereddevice(PD) connected.
Light:ThereisaPoEPDconnectedtotheportandpowerissupplied
successfully.
Blink:Indicatesportabnormalpowersupply.

2.2) RearPanel

TherearpanelofthePoESwitchcontainsafullrangeACinletpowersocket(100to240VAC,
50/60HZ)andagroundingscrew.IncasetheACcordisnotconnectedtoground,youmust
groundtheunitusingthegroundingscrew!










Menu
Enter
Back
19
20
17
18
19
20
8.4
01
W
‐‐‐M631M
ULP
02 ‐‐‐M 921M
OLP
03 ‐‐‐M‐‐‐M
SCP
04 125M‐‐‐M
2.2W05 ‐‐‐M‐‐‐M
23.706 W ‐‐‐M‐‐‐M
16.807 W ‐‐‐M‐‐‐M
13.408 W ‐‐‐M920M
18.909 W 856M856M
‐‐‐‐10 W 238M238M
11 OFF ‐‐‐M‐‐‐M
23.312 W 323M323M
5.813 W 983M983M
7.314 W 223M223M
GeneralInformation
MenuControls
LEDIndicators PoEDownlinkPorts SFP + RJ45
UplinkPorts
LCD Monitor
ACPowerPort
GroundConnection

Page | 6 COLORLCDPOESWITCHUSERMANUAL



3) LCDFeatures:

ThisPoEswitchlineisequippedwithcolor LCD display and PoE. The LCD can display the statusof
theswitchaswellasindependentstatusforeachofthePoE portssuch as: Output power,Overload,
Shortcircuit,Lightload,Lowvoltage,Overvoltage,HightemperatureEtc.

3.1) GeneralStatusIndicators:

1) PortNumber.Remainingportswillbedisplayedinthe
nextpage.
2) Portpowerconsumption
3) Portdownloadreal‐timebandwidth.
4) Portuploadreal‐timebandwidth.
5) PB:thetotal“PoEbudget”oftheswitch
6) TP:“Totalpower”undercurrentuse
7) PD:Numbersof“PDdevice”
8) Norm: Work mode. “Norm” for normal, VLAN and
CCTVavailable
3.2) GeneralWarnings:


Problem:PowersupplyfailureProblem:HighACvoltageinput Problem:LowACvoltageinput
Result:SwitchrestartResult:PortsareofftopreventdamageResult:Portsareofftopreventdamage

General Information
‐‐‐‐01 W ‐‐‐M‐‐‐M
‐‐‐‐02 W ‐‐‐M‐‐‐M
‐‐‐‐W03 ‐‐‐M‐‐‐M
‐‐‐‐W04 ‐‐‐M‐‐‐M
‐‐‐‐W05 ‐‐‐M‐‐‐M
‐‐‐‐06 W ‐‐‐M‐‐‐M
‐‐‐‐07 W ‐‐‐M‐‐‐M
‐‐‐‐08 W ‐‐‐M‐‐‐M
‐‐‐‐09 W ‐‐‐M‐‐‐M
‐‐‐‐10 W ‐‐‐M‐‐‐M
‐‐‐‐11 W ‐‐‐M‐‐‐M
‐‐‐‐12 W ‐‐‐M‐‐‐M
‐‐‐‐13 W ‐‐‐M‐‐‐M
‐‐‐‐14 W ‐‐‐M‐‐‐M
WARNING！
PSEfailure.
Restarting∙∙∙
PD:0PB:380W TP:0.0W Norm
General Information
‐‐‐‐01 W ‐‐‐M‐‐‐M
‐‐‐‐02 W ‐‐‐M‐‐‐M
‐‐‐‐W03 ‐‐‐M‐‐‐M
‐‐‐‐W04 ‐‐‐M‐‐‐M
‐‐‐‐W05 ‐‐‐M‐‐‐M
‐‐‐‐06 W ‐‐‐M‐‐‐M
‐‐‐‐07 W ‐‐‐M‐‐‐M
‐‐‐‐08 W ‐‐‐M‐‐‐M
‐‐‐‐09 W ‐‐‐M‐‐‐M
‐‐‐‐10 W ‐‐‐M‐‐‐M
‐‐‐‐11 W ‐‐‐M‐‐‐M
‐‐‐‐12 W ‐‐‐M‐‐‐M
‐‐‐‐13 W ‐‐‐M‐‐‐M
‐‐‐‐14 W ‐‐‐M‐‐‐M
WARNING！
HighACVoltage.
Allportsoff.
PD:0PB:380W TP:0.0W Norm
General Information
‐‐‐‐01 W ‐‐‐M‐‐‐M
‐‐‐‐02 W ‐‐‐M‐‐‐M
‐‐‐‐W03 ‐‐‐M‐‐‐M
‐‐‐‐W04 ‐‐‐M‐‐‐M
‐‐‐‐W05 ‐‐‐M‐‐‐M
‐‐‐‐06 W ‐‐‐M‐‐‐M
‐‐‐‐07 W ‐‐‐M‐‐‐M
‐‐‐‐08 W ‐‐‐M‐‐‐M
‐‐‐‐09 W ‐‐‐M‐‐‐M
‐‐‐‐10 W ‐‐‐M‐‐‐M
‐‐‐‐11 W ‐‐‐M‐‐‐M
‐‐‐‐12 W ‐‐‐M‐‐‐M
‐‐‐‐13 W ‐‐‐M‐‐‐M
‐‐‐‐14 W ‐‐‐M‐‐‐M
WARNING！
LowACVoltage.
Allportsoff.
PD:0PB:380W TP:0.0W Norm

Page | 7 COLORLCDPOESWITCHUSERMANUAL



3.3) PortStatusWarnings:

OLP(OverloadProtection): Theportisoverloaded
andwasshutdown.
ULP(UnderloadProtection):Theportisconsuming
extremelylowpowerwhichmightindicateafaultand
thereforetheporthasshutdown.
SCP (Short‐Circuit Protection): The port appears to
beshort‐circuitedandwasshutdown
OFF:Portnotinuse
3.4) MenuandOperations:

Clickandholdthemenubuttonfor5secondinordertoaccessthemainmenu:

Scrollthemenuusingthe“Up”and“Down”buttons,confirmusingthe“Enter”buttonandcancel/go
backusingthe“Back”button.
Themainmenucontains12options.Thenextchapterwillgothroughit.
3.4.1. SwitchMode:

TheColorLCDPoEswitchseriessupport3workingmodes:
1) Normal:TheswitchoperatesasanormalIEEE802.af/at
PoEswitchinstandardoperationmode.
2) FixedVLAN:Thiswillenableapre‐madeVLANsettings
thatwillpreventthedownlinkportsfromany
communicationsbetweenthemselves.TheVLAN
enhancessecuritybypreventingunauthorized
connectiontoanyavailableporttocommunicatewith
theIPcamerasandotherequipmentconnectedtothe
switch.Itwillalsooptimizenetworktraffic.
8.4
01
W
‐‐‐ M631 M
ULP
02 ‐‐‐ M921M
OLP
03 ‐‐‐ M‐‐‐ M
SCP04 125 M‐‐‐ M
2.2W05 ‐‐‐ M‐‐‐ M
23.706 W ‐‐‐ M‐‐‐ M
16.8
07 W ‐‐‐ M‐‐‐ M
13.408 W ‐‐‐ M920 M
18.909 W 856 M856 M
‐‐‐‐10 W 238 M238 M
11 OFF ‐‐‐ M‐‐‐ M
23.312 W 323 M323 M
5.8
13 W 983 M983 M
7.314 W 223 M223 M
Switch Port Information
8.4
01
W
‐‐‐ M631 M
ULP
02 ‐‐‐ M921M
OLP
03 ‐‐‐ M‐‐‐ M
SCP04 125 M‐‐‐ M
2.2W05 ‐‐‐ M‐‐‐ M
23.706 W ‐‐‐ M‐‐‐ M
16.8
07 W ‐‐‐ M‐‐‐ M
13.408 W ‐‐‐ M920 M
18.909 W 856 M856 M
‐‐‐‐10 W 238 M238 M
11 OFF ‐‐‐ M‐‐‐ M
23.312 W 323 M323 M
5.8
13 W 983 M983 M
7.314 W 223 M223 M
General Information
SwitchMode
Options:
Normal
FixedVlan
CCTVMode
<
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur

Page | 8 COLORLCDPOESWITCHUSERMANUAL



3) CCTVMode:CCTVmodewillenable“FixedVLAN”togetherwithrestrictingthedownlinkport
bandwidthto10Mbpsduplexcommunication.TheCCTVmodeallowstheinstallertoreach
distancesofupto250moverstandardCat.5ecable.

3.4.2. PortBandwidthLimit:
Thisfeatureallowsyoutomonitorandrestricttheincoming
bandwidthcomingfromasingleport.Oncecrossed,theswitch
willsetabuzzeralarmtowarnforbandwidthoveruse.Once
enabled,thissettingwilltakeeffectonalldownlinkports.It
cannotbesetforaspecificport.
Thedefaultsettingis“Disabled”meaningthatthereisno
bandwidthrestriction.Theotheroptionsare400Mbps,
500Mbpsand600Mbps.

3.4.3. PDType:
Thereare3typesofPD.Enhance,StandardandLegacy.
Enhance:Thedefaultsettings.Itwilldetectat/afmodesand
increasethecurrentsurgelimittotheifatstandardisused.
Standard:FullconformitywiththeIEEE802.3af/atstandards.
Legacy:ShouldbeusedifthePDdevicedoesnotcomplywith
theIEEE802.3afstandard.Theswitchwilltrytodetect
compliancewithlegacystandardsandsupplypowertothePDif
detected.Thisoperationmodeshouldnotbeusedunlessadvice
bythePDmanufacturer,asitmightsupplypowertodevicesnot
designedtoreceivePoEanddamageit.

3.4.4. KeepAlive:
KeepaliveisdesignedtodetectamalfunctionofaPDdevice
thatcausedittostopcommunicationandmakeattemptto
restoreitsconnectionbyhardrebootingitbytakingand
restoringpower.Thisfeatureisdesignedtoincreasethe
system’sreliabilityandreducemaintenancetothesystem.
TheKeepAlivecanbesetforeachofthePoEportsindividually.
Thesettingsshouldbedoneasfollows:
Port(01‐16/24):Therequiredportnumber
Status(Disabled/Enabled):TheKeepAliveStatus
Startup(60~300s):TheestimatedstartuptimeofthePDdevice.OnceaPDisconnectedtothe
specifiedport,acountdownwillcommencefromtheenteredvalue.Forexample.Ifthe“Startup”
settingwassetto180,onceaPDdevicewillbeconnectedacountdownof180secondswill
commence.Theswitchwillexpecttodetectincoming/outgoingtrafficfromthePDbeforethe
countdownreaches0.
PortBandwidthLimit
Disabled
600Mbps
400Mbps
500Mbps
<
Options:
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur
n
Port1~Port24valid!
PDType
Enhance
Standard
Legacy
<
Options:
<Enter>:Confirm<Back>:Retu
r
<UP>/<Down>:Select
Port Status
01
PDKeepAlive
Disable
startup
180
Interval
180
PowerOff
5
<Enter>:Confirm<Back>:Retu
r
<UP>/<Down>:Select

Page | 9 COLORLCDPOESWITCHUSERMANUAL



Interval(60~300s):Theintervalistheallowedtimewithoutincoming/outgoingtrafficfromthePD.
Oncenotrafficisdetected,thecountdownwillcommenceaccordingtotheconfiguration.Ifthereis
stillnotrafficbythecountdownreaches0theswitchwillexecuteahardbootupprocedure.
PowerOff(5~60s):Thisvaluedeterminesthedurationofthepowercutfortherequiredswitch.After
thiscountdownreaches0,theswitchwillrestorepowertotheportandletthePDdevicebootand
initialize.


3.4.5. PSEPowerAdjust:
ThePSE(PowerSourceEquipment)isthemainpowersupplyunitfortheswitch.Inordertoincrease
itslifeandreliabilityitsrateisactuallyhigherthanthestatedpowerbank,butitisreservedfor
situationswherePDpowerrequirementsuddenlypeaksforashortmoment.
IncasethedevicesconnectedtotheswitchreachesthePB
limit,youcanmanuallyincreaseitandutilizemorepowerto
thePoEportsontheexpenseofthereservepower.

Thisfeaturehas4options:
1. Normal(100%)
2. Add5%(105%PB)
3. Add10%(110%PB)
4. Add15%(115%PB)
Note:InordertomakesurethatthePSEisnotoverloadedforalongtime,pleasemakesurethatthe
TPislowerthanthePB
3.4.6. PSEPortPriority:
ThePoEswitchhasapowerbank(PB)measuredinWatts(W).
PDwillrequirepowerfromthepowerbank.Thispowerwillbe
markedasTotalPower(TP).OncetheTPishigherthanthePB,
theswitchwillautomaticallyshutdownportsinordernotto
overloadanddamageitself.
PSEPortPriorityallowstheusertoconfigurethepriorityof
theports–actuallysettingorderofwhichtheportswillshut
down.
PSEPowerAdjust
Add5%(105%PB)
Add10%(110%PB)
Add15%(115%PB)
Options:
<Enter>:Confirm<Back>:Retu
r
<UP>/<Down>:Select
Note:
TPmustbelessthanPB!
<Enter>:Confirm<Back>:Retu
r
<UP>/<Down>:Select
PSEPortPriority
Port Priority
Critical01
High
Low <

Page | 10 COLORLCDPOESWITCHUSERMANUAL



Theprioritiesareasfollows:
Critical:Devicessetto“Critical”willshutdownlast
High:Devicesetto“High”willshutdownonceallthe“Low”prioritydevicesasshutdown.
LowPriority(DefaultSettings):Thesedeviceswillshutdownfirst.
3.4.7. PSEPortCondition:
Thissettingwilldeterminewhethertheswitchisallowedto
distributePoEtothespecifiedchannel.Thissettingismainly
usefulaftertheinitialsettingofthenetworkandthePD
devices.Afterthesystemisup,allportswithoutPDdevices
andallunusedportsshouldbedisabledfromreceivingPoE.It
willpreventoverloadingthesystembyunrequiredPoEdevices.
“Enable”isthedefaultsetting.
ThissettingwillonlyaffectPoEandwillnotaffectnetwork
communication.

3.4.8. PoEPortPower:
Thissettingcanlimitthepowersuppliedtoaspecificportasrequired.Eachportcanbeconfigured
independently.
1) Port:Portnumberforconfiguration.
2) Power(6‐36W):Thepowerlimitfortheport.Skipsin2Wintervals.
Note:PoEPortPowerisavailableforconfigurationonlyifthePDtypeissetto“Enhanced”/”Legacy”.
IfthePDtypeissetto“Standard”thePoEPortPowerisautomaticallysetto32Wandcannotbe
modified.






PSEPortPower
Port Power
10W01
PSEPortCondition
Port Status
Enable01
Disable
<

Page | 11 COLORLCDPOESWITCHUSERMANUAL



3.4.9. LCDState:
ThissettingwilldeterminethedurationofwhichtheLCD
monitorwillstayon.Theoptionsareasfollows:
1) Never(AlwaysOn):TheLCDmonitorwillstayon.
2) 10min(DefaultSetting):TheLCDwillturnoffafter
10minutes.
3) 20min:TheLCDwillturnoffafter20minutes.
4) 30min:TheLCDwillturnoffafter30minutes.


3.4.10. FanControl:
Thissettingwilldeterminetheswitchinternalfan
workingmode.Theoptionsareasfollows:
1) AlwaysOn:Thefanwillstayonregardlessofthe
PBstatus.
2) 20%PB(DefaultSetting):Thefanwillturnononce
thePBreaches20%consumption.
3) 40%PB:ThefanwillturnononcethePBreaches
40%consumption.
4) 60%PB:ThefanwillturnononcethePBreaches60%consumption.

3.4.11. DefaultSettings:
Usethisoptionifyouwishtoresetallswitchsettingsandconfigurationbacktofactorydefault.





Restoringsystem
settings......
DefaultSetting
DefaultSetting
FactoryDefault:
Cancel
Confirm<
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Return
Fancontrol
Always
20%PB
40%PB
60%PB
On<
Options:
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur
LCDState
Turnoffafter:
Never(AlwaysOn)<
10min
20min
30min
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur

Page | 12 COLORLCDPOESWITCHUSERMANUAL



3.4.12. About:
ThiswillshowyougeneralinformationaboutthePoESwitch.


4) SwitchInstallation:

ThissectiondescribeshowtoinstallyourEthernetSwitchinthebestmannerandmakeproper
connections.Pleasefollowthefollowinginstructionsinavoidofincorrectinstallationwhichmight
causedevicedamageandpotentialsecuritythreat.
GeneralInstructions:

 Donotplacetheswitchnearwateroranydamparea.Preventwaterormoisturefromentering
theswitchchassis.
 Donotplacetheswitchonanunstablecaseordesk.Theswitchmightbedamagedseverelyin
caseofafall.
 Ensureproperventilationoftheequipmentroomandkeepthealltheventilationopeningsofthe
switchfreeofobstruction.
 Makesurethattheoperatingvoltageandcurrentmatchesthepowerinputlabeledontheswitch.
 Donotopenthechassiswhiletheswitchisoperatingorwhenelectricalhazardsarepresentto
avoidelectricalshock.
 Beforecleaningtheswitch,unplugthepowerplugoftheswitchfirst.Donotcleantheswitch
withwetclothorliquid.
4.1) DesktopInstallation:

Fordesktopinstallation,pleaseattachthesuppliedcushioningrubberfeetonthebottomofeach
corneroftheSwitch.Thiswillpreventtheswitchfromshiftingorslidingandwillreduceshockin
case of external vibration. Allow adequate space for ventilation between the device and the
objectsaroundit.
Thankyoufor
Model:PoES‐24380GCL+2SFP
choosingProvision‐ISR
About
HWVer.:V3.0
SWVer.:V1.20

Page | 13 COLORLCDPOESWITCHUSERMANUAL






4.2) RackMountInstallation

Theswitchisrack‐mountableandcanbeinstalledonanyEIA‐19 compatible rack. Before
installation, pleaseinstall the mounting brackets on the switchsidepanels(oneoneachside),
securethemwiththeprovidedscrews.Donotusedifferentscrews since longer screws might
damagetheswitchcomponentsandshorterscrewsmightnotbeartheweightoftheswitchafter
installation.
Afterthebracketshasbeeninstalled,usetherackmountscrews(notincluded),inordertosecurely
mounttheswitchontherack.

Step1:Bracketinstallation










Page | 14 COLORLCDPOESWITCHUSERMANUAL



Step2:Mountingtheswitchontherack.







4.3) Turningontheswitch

Pleaseplugthepowersupplyintotheswitch,theinternalpowersystemoftheswitchcanAuto‐
regulatetheworkingpoweraccordingtotheactualinputpower.Whentheswitchispoweron,the
powerindicatorwillbelightonthefrontpaneloftheswitchshines.
Note:Pleaseconfirmthevoltageiscorrectbeforepoweron,otherwisetheswitchwillbe
damaged.(ThereisapowersupplysocketonthebackpanelofthePoEEthernetswitch.The
powerinputis:100V‐240Vac,50/60Hz.)



