ISON IS-DF306P Series User manual

1
FCC MARKING
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class A for ITE, the essential
protection requirement of Council Directive 2004/108/EC on the
approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please
check with your local distributors for the latest information. No part of
this document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
IS-DF306P Series
Quick Installation Guide

2
Introduction
This rugged designed Industrial Ethernet switch / Industrial Fast Ethernet 4 port POE Injectors,
comply with IEEE802.3af and IEEE802.3at, has pass many rigorous environmental test. It
delivers 30watts (Max 36watts) power per POE port. And it can generate t otal 126 watts power to
PD devices. the uplink 2 SFP port, can extend your environment to a much larger area .With its
multi-purpose design, it can also be used for Din-Rail or wall-mounted. It is an ideal unit for IP
surveillance, traffic monitoring and Security application in critical environment. It can tolerate -
40°C to 75°C in harsh environment to perform a reliable network.
Housing Dimension

3
MODELS –Industrial Fast Ethernet 4 port Injector, 48VDC input
This industrial high power POE+ is designed for multiple applications, especially for
vehicle surveillance, IP surveillance, and traffic monitoring and for a broad range of
outdoor applications. It can be used as a stand-alone device for buses, trucks for
Surveillance purposes. And it also can be used to cascaded/daisy-chain to other devices
to cover wider area through the SFP connection.

4
Power connection
This unit provides 6 pin terminal block. The POE port can be operated from 44-56VDC power source. The
VDC power range can be 48VDC only or lower, or wide range from 44-56VDC. Always Make sure your input
voltage is within this supported voltage range for each model.
WARNING –any exceeded input voltage will not make this unit
function and may damage this unit.
To make power connection –Follow the printed polarity for V1+, V1-,
V2+, V2-, and ground. Connect positive wire to V+ , connect negative
wire to V-, also connect neutral wire to the ground screw as shown .
Relay -- You may use 24V@1A relay connection to your external
device for special purpose. When 2 powers are connected, the relay is
in SHORT mode. When any power source fails, the relay change to
OPEN status.
Power connecting procedure:
STEP 1 –Pull out 6 pin terminal block.
STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.
STEP 3–Plug back 6 pin terminal block to its place.
WARNING –
Always ground the power source to maintain a clean power input. Due to too many cheap made
Din Rail Bracket x 1
Wall mount bracket x 2
6 pin Terminal Block x1
Installation package
This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted
bracket are included.

5
Dip switch function
Amber LED
ON – 100M speed is detected.
OFF – 10M or 100M speed is detected
P1
ON -- when V1+, V1- is connected
1
ON – port 1 SFP fiber is detected
OFF – port 1 SFP fiber is not detected.
Flashing – port 1 SFP fiber is active
Green LED
ON—TX link is detected
OFF – TX port is not detected
Flashing – TX port is active
LED indicator
This unit is equipped with dip switches, located on the front panel. Adjusting the dip switches will
change the default function of this unit. This unit has set to manufacturer default as: Port 5 SFP and the
speed is set to 1000M for both port 1 and port 2 SFP ports. you may adjust dip switch setting to select
port 5 as TX ( disable port 5 SFP) or set SFP speed to 100M. The detail setting as shown below:
P2
ON -- when V2+, V2- is connected
ALM
ON –
connect only PW1 or PW2.
OFF-
both PW1 and PW2 are connected
2
ON – port 2 SFP fiber is detected
OFF –port 2 SFP fiber is not detected.
Flashing – port 5 SFP fiber is active
3,4,5,6
ON—PD is detected on designated
port.
OFF – no PD is detected

6
Specification:
IEEE Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE802.3x Flow Control and Back Pressure,
IEEE802.3af for POE
IEEE802.3at for POE+
Switch Architecture
Back-plane (Switching Fabric): 12Gbps
Data Processing
Store and Forward
Flow Control:
IEEE 802.3x Flow Control and Back Pressure
Jumbo Frame
9KB
MAC address Table Size
1K
Packet Buffer Size
1Mbits
Network Connector :
5xRJ-45 10/100BaseT(X) auto negotiation,
4 Fast Ethernet POE+ 802.3at/af PSE port
Auto MDI/MDI-X function, Full/Half duplex
2 x SFP 100/1000M BaseX
Network Cable
UTP/STP above Cat.5e Cable
EIA/TIA-568 100-ohm (100m)
Fiber Cable (Multi-mode):50/125um,62.5/125um
Fiber Cable (Single-mode): 9/125um
Protocol
CSMA/CD
LED
P1(Power 1) Green,
P2(Power 2) Green,
ERR( Fault ) Amber,
TX/RJ-45 port:
Green LED (Link/Active) Green,
Amber LED(Speed) 10/100(OFF ) ,100 (Green)
SFP Fiber Per port:
Link (Green)
Active Flash
Reserve polarity protection
Present
Overload current protection
Present
Power Supply
Redundant Dual DC 9V-56V Power Input without POE
Power Consumption
5.76W@12/24/48 VDC full load, Without POE

7
Alarm Relay Contact
Relay outputs with current carrying capacity of 1 A @24VDC,
Relay in short circuit mode when 2 powers are connected. in
open circuit mode when only one power supply is connected
Ethernet Switch power input
Ethernet switch power input 9VDC -56VDC
POE power
input Voltage 44VDC-56VDC.
POE power per port 30watts. Maximum 36Watts
Maximum total power 126Watts
Removable Terminal Block
Provide 2 Redundant power , Alarm relay contact ,6 Pin
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire(AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
Operating Temperature
-40℃~75℃fully tested.
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40℃~85℃
Housing
Rugged Metal ,IP30 Protection
Case Dimension (W X D X H)
142mmx43mmx105mm (LxWxD)
Installation mounting
DIN Rail mounting and Wall Mounting
EMC/EMS
CE, FCC,VCCI
EMI
FCC Part 15 Subpart B Class A,
CE EN 55022 Class A