Proxi gate User manual

www.getproxi.com
Gate

Information about the rB-TO2S2 module
The module is used to control entry gates and garage doors with a mobile device. It coopera-
tes with gate controllers produced by dierent manufaurers.
Purpose
Operation
The module allows an entry or garage door
to be controlled with a mobile device as well
as by a traditional remote control.
The free Proxi application can be downlo-
aded from Google Play and the App Store. It
requires a mobile device that is compatible
with Bluetooth 4.0 and iOS7 or Android
version 4.3 or newer.
The Proxi Gate module has two outputs
that allow the control of two gates, a gate
and a door or two funions of one gate.
The operating mode of the module’s output
channels are configured with the help of the
mobile app.
The available modes are monoable (single
impulse returned at the output) or biable
(maintaining the output ate).
If the monoable ate is seleed, the
period for which the on ate at the output is
maintained should also be set. The default
period is 1 second.

Inallation
The Proxi Gate module has a waterproof
housing rated at IP65 with an external
antenna conneion. This allows an antenna
to be fied in the optimal location to extend
the radio range, e.g. away from the gate
ruure.
To conne the module to the gate controller,
open the housing and conne the cables to
the junion located on the PCB (Fig. 1).
Four cables are sucient to control a single
gate funion.
1. PWR +/-/~
2. PWR -/+/~
3. OUT1+
4. OUT1-
5. OUT2+
6. OUT2-
7. IN1 A *
8. IN1 B *
9. IN2 A *
10. IN2 B *
Conne the Proxi Gate conneor terminals to the terminals of the gate controller. The basic
method of inalling the Proxi Gate module is to conne it to the input of the manual control
switch. The location and terminal description depends on the gate controller module being
used.
Detailed information on the funioning of the gate controller and a description of the con-
neors can be found in the inruions for the given controller model.
Fig. 1. View of part of the PCB together with the 10-pin conneor
* Not supported in version 1.0.0
Inallation
1 2 3 4 5 6 7 8 9 10

Inallation
In mo gate controllers, the voltage required to power the switches, photocells and lighting
at the limits is available at the conneor. If the voltage is in the range of 9-25V DC or AC, it
should be used to power the Proxi Gate module. Any power polarity can be used.
When conneing output channel cables, the
conneor polarity given in the description
should be maintained. Depending on the
desired configuration, one or two Proxi Gate
module channels can be conneed.
Power supply conneion:
Conneion of the Proxi Gate
output channels:
Single channel control
Two channel control
The typical operation of a gate controller is
a sequence of “open-op-close” or “open-
-close”. To control the gate with one switch in
the mobile app, apart from the power supply,
two circuits should be conneed:
1. OUT1+ should be conneed to the appro-
priate input of the gate controller, usually
that for manual control or an additional
radio receiver.
2. OUT1- should be conneed to the Ground
of the gate controller, usually marked as
COM, GND or “-“.
The Proxi Gate module operation in two-
-channel mode is analogous to that of a
remote control with two buons.
To control two funions of the gate with
the help of two buons in the mobile app,
conne the power and the control circuits
as follows:
1. OUT1+ should be conneed to the appro-
priate input of the gate controller, usually
that for manual control or an additional
radio receiver.
2. OUT1- should be conneed to the Ground
of the gate controller, usually marked as
COM, GND or “-“.
3. OUT2+ should be conneed to the appro-
priate second input that controls the second
gate funion, usually the door funion
(partial opening), the funion of opening
with maintenance of the ate (the gate does
not close automatically), or other.
4. OUT2- should be conneed to the Ground
of the gate controller, usually marked as
COM, GND or “-“.

Inallation
Fig. 2. Example of the conneion of one channel of the Proxi Gate module to the gate
controller (Beninca JM3 controller)
1 2 3 4 5 6 7 8 9 10
17 16 15 14
5 6 7 8
1 2
13 12
+
–
S
21 20 19 18
JP7 JP1
S1
DL1
P.P. PGM CL
ON
ANT
TCAANPO
24Vac
1A max
LAMP
24Vac / 15Wmax
AMPC +++– – –
JP4
ENCODER
SERVICE LIGHT
24Vac/10W
PHOT
STOP
P.P.
COM
SHIELD
ANT
4 3 2 1
2AFF1

Inallation
Fig. 3 shows examples of where the Proxi Gate antenna module could be fied inside the
garage. Location 1 is the be and recommended for the be radio range. In location 4, the
signal is mo dampened.
Fig. 3. The location of the Proxi Gate antenna module
The Proxi Gate module has an antenna and
a cable that is conneed by screwing in
the antenna conneor to the SMA socket
located on the exterior of the housing.
A 27mm antenna is aached to the end of
the cable. To ensure the be radio range for
Inallation of the Proxi Gate module
3
1
4
2
the module, the antenna should be fied
outside of the garage or the conruion
of the gate. Inallation of the antenna on
a metal gate will dampen the radio signal.
If the antenna has to be fied inside, it
should be located by the front wall, beside
the doors.

Operating temperature
Proteion code
Power voltage
Peak power voltage
Peak current
Average power
Number of outputs
Output polarity
Output galvanic separation
Max load voltage
Max load current
Max output voltage at switching on
Surge proteion
Output overvoltage proteion
Proteion again
reverse output polarity
ENVIRONMENTAL CONDITIONS
ELECTRICAL PARAMETERS
OUTPUTS
-30 °C / +55 °C
IP65
AC/DC 9 V–24 V (any polarity)
50 V
70 mA
120 mW
2
Yes
Yes (each separately)
DC 50 V
DC 20 mA
0,3 V
(for a load current of 20 mA)
Yes
Yes
Yes
(diode conta with thermal fuse)
Technical data

Number of inputs
Output galvanic separation
Min. input voltage
Max. input voltage
Surge proteion
Input mode
INPUTS
2 (inputs with polarity deteion)
Yes
AC/DC 10 V
AC/DC 25 V
No
Monoable/Biable
(mode and duration are defined by the app)
Technical data
F&F Filipowski . j., ul. Konantynowska
79/81, 09-200 Pabianice, POLAND, tel./fax
[phone], fif@fif.com.pl, www.fif.com.pl
©2014 F&F Filipowski . j. All rights reserved.
Guarantee: F&F produs are guaranteed
for 24 months from the date of purchase.
908312 5973845
Radio conneion
Signal power
Transmission type
Coding
RADIO PARAMETERS
Bluetooth, 2,4 GHz
6 mW
Bi–directional
Yes