PT W41037 User manual

Rolling Engine Stand
with Straps
OWNER’S MANUAL
Stock Number W41037
FOR YOUR SAFETY,
please read these instructions carefully and retain them for future use.
LIMITED WARRANTY
PERFORMANCE TOOL extends only the following warranties, and only to original retail purchasers. These warranties give
specific legal rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all
exclusions and limitations of warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL warrants the product to be free from defects in materials and workmanship under normal use and
service. A defective product may be returned for a free replacement within 90 days from the date of purchase, provided that
product is returned to place of purchase immediately after discovery of defect. After 90 days and up to 1 year from date of
purchase, PERFORMANCE TOOL will replace at no charge any parts which our examination shall disclose to be defective and
under warranty. These warranties shall be valid only when a sales receipt showing the date of purchase accompanies the
defective product or defective part(s) being returned. For part(s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 24086 Seattle, WA 98124
These warranties exclude blades, bits, punches, dies, bulbs, fuses, and other consumables which must be replaced under normal
use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed,
or which has been repaired or altered in any way so as to affect adversely its performance or reliability, nor shall these warranties
apply to any product or part which has been subject to misuse, neglect, accident or wear and tear incident to normal use and
service.
PERFORMANCE TOOL does not authorize any other person to make any warranty or to assume any liability in connection with
its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL makes no express or
implied warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL makes no implied warranty of
merchantability and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for
personal, family or household use and not for commercial or business use, PERFORMANCE TOOL makes an implied warranty of
merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular
qualities or characteristics, and for the duration, expressly warranted above. The laws on limitation of implied warranties may differ
from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL shall not be liable for consequential, incidental or special damages resulting from or in any manner
related to any product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective
product or part shall be the repair, or replacement thereof as provided above. The laws on limitation of remedies or on
consequential, incidental or special damages may vary from state to state, so the above limitations may not apply in all cases.
Copyright © 2008 PERFORMANCE TOOL – All rights reserved
On occasion, after printing of our literature is completed, the manufacturers may make changes and/or
modifications to their product which won’t be reflected in this manual. Although we strive to maintain
complete and accurate information, it is possible in certain instances that the product may differ
slightly from printed specifications.

1. Measure length of oil pan. This determines where the cross-braces
(3) are attached to the frame (2). (See Fig.1)
2. With set screw holes facing inwards, slide 2 support uprights (4)
onto each cross-brace (3).
3. Attach casters (1) through frame (2) and cross-braces (3), with nut
(5), split washer (6), and flat washer
(7) at desired length based on
measurement in step 1. The length of
the cross-braces (3) should be a
minimum of 2 ‘’ and a maximum of 4’’
shorter than the overall length of the
oil pan. Tighten nut (5).
ASSEMBLY INSTRUCTIONS
SPECIFICATIONS
Capacity: ......................... 750 lbs.
Length: ............................. 21-3/4"
Width: ..................................... 18"
Height: .............................. 13-3/4"
PARTS LIST
1 Casters 4
2 Frame 1
3 Cross-Braces 2
4 Support Uprights 4
5 M12 Nut 4
6 M12 Split Washer 4
7 M12 Flat Washer 4
8 Set Screw 4
# Description Qty. # Description Qty.
Read these safety warnings before operation.
WARNING!
Failure to heed these warnings may result in loss of load,
damage to engine stand, and/or engine stand failure resulting
in personal injury or property damage.
WARNING!
Do not overload engine stand beyond rated capacity.
Overloading can cause damage to or failure of the engine
stand.
Always use stand on hard, level surface capable of sustaining
the load. Use of stand on other than hard level surfaces can
result in stand instability and possible loss of load.
IMPORTANT SAFETY INFORMATION
1. Visual inspection shall be made before each use of the stands,
checking for cracks, cracked welds and missing and/or damaged
parts. Any stand that appears to be damaged in any way shall be
removed from service immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED WITH
THE MISUSE OF EQUIPMENT OF THIS TYPE, NO
MODIFICATIONS SHALL BE MADE TO THE PRODUCT.
3. Replace worn or damaged parts with Performance Tool replacement
parts. Be sure that only qualified personnel perform repairs.
MAINTENANCE & INSPECTION
1
2
3
4
567
8
4. With the engine still being supported by hoist, lower the engine close
enough to the stand to properly determine width of support uprights
(4). Install set screws (8) into support uprights (4) and tighten.
5. Slowly lower engine onto stand. Using the straps provided, secure
the engine to the stand before removing hoist.
Fig.1