PT W5182 User manual

Table Top Storage Bin Rack
Stock Number W5182
OWNER’S MANUAL
FOR YOUR SAFETY,
please read these instructions carefully and retain them for future use.
LIMITED WARRANTY
PERFORMANCE TOOL extends only the following warranties, and only to original retail purchasers.
These warranties give specic legal rights. Except where prohibited by local law, the law of the State
of Washington governs all warranties and all exclusions and limitations of warranties and remedies.
There may be other rights which vary from state to state.
PERFORMANCE TOOL warrants the product to be free from defects in materials and workmanship
under normal use and service. A defective product may be returned for a free replacement within 90
days from the date of purchase, provided that product is returned to place of purchase immediately
after discovery of defect. After 90 days and up to 1 year from date of purchase, PERFORMANCE
TOOL will replace at no charge any parts which our examination shall disclose to be defective
and under warranty. These warranties shall be valid only when a sales receipt showing the date of
purchase accompanies the defective product or defective part(s) being returned. For part(s) after 90
days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, and other consumables which
must be replaced under normal use and service. These warranties shall not apply to any product or
part which is used for a purpose for which it is not design or which has been repaired or altered in
any way so as to affect adversely its performance or reliability, nor shall these warranties apply to
any product or part which has been subject to misuse, neglect, accident or wear and tear incident
to normal use and service.
PERFORMANCE TOOL does not authorize any other person to make any warranty or to assume any
liability in connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE
TOOL makes no express or implied warranties of any kind with respect to its products. In particular,
PERFORMANCE TOOL makes no implied warranty of merchantability and no implied warranty of
tness for any particular purpose, except that for goods purchased primarily for personal, family
or household use and not for commercial or business use, PERFORMANCE TOOL makes an
implied warranty of merchantability (and, if otherwise applicable, an implied warranty of tness for
a particular purpose), but only for the particular qualities or characteristics, and for the duration,
expressly warranted above. The laws on limitation of implied warranties may differ from state to
state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL shall not be liable for consequential, incidental or special damages resulting
from or in any manner related to any product, or to the design, use, or any inability to use the product.
The sole and exclusive remedy for a defective product or part shall be the repair, or replacement
thereof as provided above. The laws on limitation of remedies or on consequential, incidental or
special damages may vary from state to state, so the above limitations may not apply in all cases.
Copyright ©2012 PERFORMANCE TOOL – All rights reserved
WARNING: This product and its packaging contain a chemical known to the State of California to
cause cancer, birth defects or other reproductive harm.
Always wear eye protection when using tools.
IMPORTANT SAFETY INFORMATION
• Donotexceedratedweightcapacity.
• Redbincapacityis5lbs.each.Bluebincapacityis8lbs.each.
• Alwaysinspectbinsforanycracksbeforeuse.Ifanydamageisfounddo
notuse.

PARTS LIST
TOOLS REQUIRED
ASSEMBLY INSTRUCTIONS
• #2 Phillips head screwdriver
• 10 mm wrench or socket and ratchet
1
3
2
5
4
6
8
7
9
1. Place the feet on a at surface w/ the brackets facing
inward. Position one of the L-Bar frame legs on the
inside the bracket. NOTE: the tear drop shaped holes
should be on the longer side of the tray, with the larger
circle portion of the openings facing down.
2. Use a large screw, washer and nut to fasten the legs
to each of the feet.
3. Place the bottom bin support bracket on to the legs.
Make sure both holes in the support bracket are
closer to the top.
4. Align the holes in the base support brackets with
the threaded holes on the base, and holes in the legs.
Fasten the top holes with a large screw, washer and
nut. Fasten the bottom holes with two small machine
screws.
5. Insert remaining bin support brackets on to the legs.
6. Align the vertical support bracket with the bolts on
back of the bin support brackets, and lock into place.
Mounting to a Wall: There are 3/16 in. holes on each
cross bar that are approx 30-1/4 in. apart. If mounting to
a wall it is recommended that you mount to studs where
possible and/or use wall anchors that will support the
weight of the items you wish to store. Total weight should
not exceed 100 lbs. Use a minimum of 4 anchor points,
and more depending on the wall material, thickness, and
weight of goods being stored.
No. Description Qty.
1 Bottom Feet 2
2 Base Support Brackets 2
3 “L-Bar”Frame Legs 2
4 Bin Support Brackets 4
5 Vertical Support Bracket 1
6 Large Machine Screws 10
7 Round Washers 10
8 Hex Nuts 10
9 Small Machine Screws 2
SPECIFICATIONS
NOTE: Specications are subject to change without
notice.
Red Bins: ..................... 14 (6-1/2 L x 4-1/16 W x 3 in. H)
Blue Bins: .............................10 (9-1/4 L x 6 W x 5 in. H)
Rack Height: .................................................... 25-1/4 in.
Rack Width: ............................................................32 in.
Rack Depth: ..................................................... 10-1/8 in.
Construction: ................................ Powder Coated Steel