Puffco PEAK User manual

PEAK INSTRUCTION MANUAL

SHARE THE VIEW:
Use #PuffcoPeak to share your experience.
We’ll share your photos and videos with our
global audience (seriously we will).
Puffco
Whats inside / p 3
Quick start / p 4 - 8
Temperature settings / p 9
Battery / p 9
Cleaning your device / p 10
Advanced features / p 11
Warning / p 11
Peak Protection / p 12
YOU’RE ALMOST TO THE TOP!
We know it’s a drag, but please read through
all the directions. This device is the first of
its kind, and we’d like you to learn the easy
way by reading this booklet. You’ll learn
some secret tips and tricks as well!

A: Loading tool
B: Cotton swabs
C: USB cable
D: AC adapter
E: Glass attachment*
STEP 1: Fully charge device before first use.
Device pulses white while charging, and turns
off automatically when complete.
STEP 2: Fill glass with water just above the
air-holes. Do not fill glass while attached to base.
X- Do not allow water in lower section!
AEF
G
H
I
J
B
C
D
WHAT’S INSIDE: QUICK START:
F: Carb cap*
G: Atomizer cover
H: Ceramic bowl (2)
I: Atomizer
J: Base
1
2
03 04
*Each glass piece is hand blown, and may vary slightly in size.
X

STEP 5: Single click to toggle through heat settings.
BLUE (Small load) / 450 ° - GREEN (Medium) / 500 °
RED (Large) / 550 ° - WHITE (XL) / 600 °
STEP 3: Carefully push glass into the base.
Align inlet hole on the front of the glass ( )
with atomizer.
STEP 6: Use Loading tool to place contents on
the bottom surface of the bowl (not the side).
STEP 4: To lock / unlock the device,
hold down the button for 3 seconds.
3 5
46
05 06

STEP 7: Place carb cap on top of atomizer.
STEP 8: Double click to initiate heat-up (20 second
avg. heat-up time). Press and hold button anytime to
exit. Pulsing light indicates heat-up mode is active.
STEP 9: Device will vibrate and lights will flash when
ready. Inhale repeatedly until device is finished
producing vapor. *See p. 11 for sesh mode.
STEP 10: Use a cotton swab to clean
the chamber after each use.
7 9
810
07 08

TEMPERATURE SETTINGS:
BATTERY:
To cycle through the 4 temperature settings,
click the button once.
LOW (Small load) / 450° > 20 sec. heat up
MEDIUM (Medium load) / 500° > 20 sec. heat up
HIGH (Large load) / 550° > 25 sec. heat up
PEAK (XL load) / 600° > 25 sec. heat up
The Peak device features intelligent temperature
calibration, which provides a more consistent
experience during repeated use. This means
that all heat up times vary.
Click the button 3 times to check battery life.
Color will indicate remaining battery life.
Battery fully charges in 2 hours.
1. Clean carb cap, glass, and atomizer by soaking in
isopropyl alcohol. Atomizer can be cleaned fully
assembled or disassembled.
2. Be sure to clean gold connector on base and bottom
of atomizer with an alcohol soaked cotton swab.
3. WARNING: After cleaning, rinse and allow all parts
to dry before use.
*Before removing atomizer, make sure bowl has cooled.
*Do not get the base wet - it’s electric - it will break.
*Throughly clean device every 20 uses.
CLEANING:
LOW MED HIGH PEAK
09 10
100% - 60% 60% - 30% 15% - 0%
Preparation: Remove glass before unscrewing and
re-inserting atomizer (don’t overtighten the atomizer).

ADVANCED FEATURES:
WARNINGS:
- Do not allow water in the bottom chamber of glass.
- Do not let water seep into the atomizer.
- Do not overfill glass.
- Do not store device with water in the glass.
- Remove glass before unscrewing and inserting atomizer.
- Attach / detach glass carefully, do not force.
- Wait 1 minute between uses.
- Do not fire atomizer 4 times consecutively.
- Several short inhales produce more vapor.
- Do not place contents on the sidewalls of the bowl.
- Do not overfill chamber.
- If you experience a bug, turn the device on and off.
Should the issue persist, contact support.
- Keep away from extreme hot and cold temperatures.
- Keep away from moisture and high humidity.
Sesh Mode:
Haven’t reached your peak? We got you covered.
We created a sesh mode that increases heat and
extends your session by 15 seconds. Use it to boost
heat, or to share with your friends.
If vapor production is low, double click to initiate
sesh mode. Still not enough? Damn you’re
hardcore, sesh again! You can double click as many
times as you want to keep the session going.
Multicolored light flash: When there is a poor or no
connection between the base and atomizer,
you’ll see a rainbow light.
5 red light flashes: Indicates short circuit.
Red light holds: Device overheated.
11 12
Puffco One-Year Limited Warranty Summary:
Puffco provides one year of coverage for only the
electronic base. This covers defects in materials
and workmanship for one year from the date of
original retail purchase. Puffco does not warrant
glass, atomizers, normal wear and tear, or damage
caused by accident or abuse. To obtain service,
email Puffco customer care at [email protected]
or visit https://Support.Puffco.com/hc/en-us.
Call charges and international shipping charges
may apply, depending on the location. Subject to
the full terms and detailed information listed on
Puffco’s website under local consumer laws.
You may be required to furnish proof of purchase
details, and the device itself when making a claim
under this warranty. Do not attempt to open the
Puffco Peak base, this will immediately void the
warranty for your product.
PEAK PROTECTION:
We want to make sure you have a consistently
perfect experience. Should something go wrong,
visit Puffco.com to view FAQ’s (your question might
be covered there). If not, you can livechat with a
specialist on our site or contact customer care
at [email protected].
- PUFFCO QUALITY GUARANTEE -
[email protected]

SHARE THE VIEW:
Use #PuffcoPeak to share your experience.
Kindly follow us on instagram!
Puffco
13
LEGAL:
For all Puffco products, strictly use as intended. Puffco
units should be used only by persons of legal age in
congruence with state and or federal law.
Know that Puffco reserves the right to verify the age of
the consumer prior to every purchase.
Registered Puffco products are not intended for any
use which is illegal under any state or federal law.
Moreover, Puffco products aren’t intended to diagnose,
prevent, treat, or cure any disease or medical
condition. If you are pregnant, nursing, taking
medication for a medical condition, or suspect you
have a medical condition, please consult your
physician before using any Puffco product.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Thank you for choosing Puffco. Welcome to the family.
Puffco products are designed and engineered in
Brooklyn, NY and assembled in China.

by Puffco Creation Labs - Subject to alterations · All rights reserved
13-352-11111