Aspire Nautilus User manual

Thank you for your purchase of the Aspire Naulus tank system.
Before using the Naulus, please read through the manual for proper
care and use. This will insure connued enjoyment of your Naulus Tank.
Please keep manual for future reference.
The Naulus is the next generaon of tank systems. Made of stainless
steel and Pyrex glass, the Naulus also uses the Aspire “BDC” (Boom
Dual Coil) atomizer technology.
The Naulus has an exclusive adjustable airflow design that is
revoluonarily. With a simple turn of the lower ring, you have four
opons to adjust airflow to meet people’s different requirements for
vaping. With the opon of different size air-ports, it allows the user to
produce big clouds of vapor, with a pure and clean taste. With the unique
Naulus four-port system, you can now adjust how hard or so the draw
is, how warm or cold the vapor is, and how much vapor is produced. The
Naulus is also very easy to install and refill.
Aspire…the trusted name in Personal Vaporizers.
Naulus

Configuraon
Contents of kit:
* Complete Naulus Tank (1.6 ohm atomizer pre-installed)
* 1 replacement atomizer (1.8 ohm)
* 1 eGo threaded cone
* 1 user manual

Naulus Exploded View
Airflow adjustment ring
Replaceable Atomizer
(Aspire BDC)
Upper hardware
PYREX Glass tank
Drip p
Boom hardware

How to assembly
1. Screw the upper hardware to
the Pyrex tank
(DO NOT over ghten!).
2. Screw the BDC Atomizer into
the boom hardware
(make sure the BDC atomizer
is snugged down hand ght).

How to assembly
3. Snugly screw the Tank hardware
to the boom Atomizer
hardware (the atomizer screws
onto the air-tube sha in
center).
4. Insert the drip-p into the
upper hardware.

How to fill liquid
2. Screw the boom hardware
off the upper hardware.
1. Check to make sure the upper
stainless steel be screwed
ghtly onto the glass tank.

How to fill liquid
When you screw off the boom hardware, the atomizer
should be screwed off the upper hardware at the same me,
in case the atomizer is sll kept onto the air-tube sha in
center, please screw the atomizer off and screw back onto
the boom hardware in order to avoid disconnecng.

How to fill liquid
4. Screw the boom hardware
back onto the upper hardware.
3. Fill liquid into the space between
the glass tank and the center
metal tube. DO NOT over fill or
get liquid into the center sha.

How to fill liquid
A: Don’t fill the liquid into the central hole.
B: Let the Naulus stand for 2 minutes before use—this will let e-liquid absorbed
into the wick/atomizer chamber.
C: For use with eGo baeries: screw the supplied cone onto the threads, and then
install the Naulus onto the baery.
D: If you experience a burning taste the first couple of puffs, it’s because the liquid
has not absorbed into the wick. Give the liquid me to be absorbed and try again.

User Manual FOR
Copyright All right reserved
PATENT PENDING
DESIGNED AND MANUFACTURED BY
EIGATE TECHNOLOGY

How to adjust airflow
Airflow hole size: Ø0.9mm
Ø1.1mm
Ø1.4mm
Ø1.8mm
The Naulus unique airflow valve
features 4 different sizes to control the airflow to the amount you prefer.
Rotate the Airflow control valve to the most comfortable one for you.

How to clean & Noces
NOTICES
1. The glass tank should not be impacted, dropped, or mishandled,
otherwise the glass tube may be broken, and injury may occur.
2. When disassembling, please remove the boom hardware first,
and then screw off the glass tank.
3. Do not fill the Aspire Naulus over 5ml; when the liquid level is
below 0.5ml, should be refilled to avoid a dry wick.
4. If the boom hardware is hard to be screwed off, please screw
the upper hardware with the glass tank ghtly and then the
boom hardware will be easy to screw off.
When necessary, clean the components (except the BDC Atomizer)
by washing with clean water, and air-drying the components.