Pulsar NS Series User manual

2010 AeroLEDs LLC 0008-0005 Page 1
Manufactured by: Installation Guide:
AeroLEDs LLC Pulsar NSP and NS Series Lights
967 East Park Center Boulevard P/N 01-1080-C or P/N 01-1080-B
Suite # 381 LED Navigation and
Boise, ID 83706-6700 nti-Collision Light
Phone: [phone]
www.aeroleds.com
[e-mail]
Exceeds 100 candela for position lights and 400 effective candela for strobes
Operating Instructions:
Operational Voltage: 14 & 28 Volt Systems
Position Input Current: 0.4 at 14V, 0.2 at 28V
Strobe verage Current: 0.8 at 14V, 0.4 at 28V
Strobe Peak Current: 2.25 at 14V for 0.33 seconds
CONTINUED IRWORTHINESS:
The Pulsar NS ser es LED nav gat on and ant coll s on
l ght assembly s des gned w th 4 forward nav gat on LEDs, 2
rear pos t on LEDs, and 18 LEDs mounted beneath the ant -
coll s on lens. Should any one LED fa l, the un t must be
repa red or replaced. V ew LEDs w th weld ng goggles for
eye safety.
INST LL TION PROCEDURES:
1. The nstallat on procedure descr bed n the follow ng text s for a
s ngle l ght nstallat on, but the procedure s dent cal for mult ple
l ght nstallat ons.
2. Pr nt out the nstallat on template (the page 3 of th s document),
however be sure to set up the pr nter dr ver to NOT use Page
Scal ng so the pr nter w ll repl cate the template to the proper 1:1
scale, otherw se the template w ll be too small. The proper scal ng
can be ver f ed by plac ng the ncluded ‘Y’ Mount ng Bracket over
the pr ntout to ensure a 1:1 f t.
3. By des gn, the ‘Y’ Mount ng Bracket locks nto the NS product
body.
4. Pr nt the template as descr bed above and conf rm a 1:1 scal ng of
the pr ntout.
5. Attach the template to the w ngt p (mount ng) pos t on and mark
the screw and w re hole locat ons.
6. Mount the bracket us ng three 6-32 100 degree countersunk
screws. Ensure that the mounting bracket is grounded to
structure via the mounting screws. If necessary, route a ground
strap from one mount ng screw to structure ground or term nate
the ground sh eld from the sh elded w re bundle to a mount ng
screw. Proper chass s ground s requ red for m n mum RFI and for
protect on from d rect l ght ng effects.
7. Connect the red w re to sw tched power for the pos t on l ghts,
connect the yellow w re to sw tched power for the strobe l ghts,
connect the black w re to the structure ground used to ground
the mount, and connect the green w re to the synchron zat on
w re from the other nstalled l ght(s). It s recommended that the
attached w r ng d agram be followed for m n mum RFI.
8. Attach the l ght to the mount ng bracket and anchor n place w th
the 8-32 hex head set screw (prov ded) that nserts nto the rear
of the l ght.
9. Check all av on cs systems for nterference from th s nstallat on.
10. A fl ght check should be performed by a properly cert f ed p lot.

2010 AeroLEDs LLC 0008-0005 Page 2

2010 AeroLEDs LLC 0008-0005 Page 3

2010 AeroLEDs LLC 0008-0005 Page 4