Pulsar PG15KVTWB User manual

Model: PG15KVTWB
www.pulsar-products.com
Generator
OPERATOR’S MANUAL

1
INTRODUCTION
Congratulations on your selection of a this generator. We are certain you will be pleased with your purchase of one of
the finest generators on the market.
We want to help you get the best results from your new generator and to operate it safely. This manual contains all the
information on how to do that; please read it carefully.
As you read this manual, you will find information preceded by a symbol.
That information is intended to help you avoid damage to your generator, other property,
or the environment.
We suggest you read the warranty policy to fully understand its coverage and your responsibilities of ownership.
When your generator needs scheduled maintenance, keep in mind your THIS servicing dealer is specially trained in
servicing THIS generators. Your authorized THIS servicing dealer is dedicated to your satisfaction and will
be pleased to answer your questions and concerns.
AFEW WORDS ABOUT SAFETY
Your safety and the safety of others are very important. And using this generator safely is an important responsibility.
To help you make informed decisions about safety, we have provided operating procedures and other information on
labels and in this manual. This information alerts you to potential hazards that could hurt you or others.
Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining a
generator. You must use your own good judgement.
You will find important safety information in a variety of forms, including:

Safety Labels on the generator.

Safety Messages preceded by a safety alert symbol and one of three signal words, DANGER, WARNING, or
CAUTION.

Safety Headings such as IMPORTANT SAFETY INFORMATION.

Safety Section such as GENERATOR SAFETY.

Instructions how to use this generator correctly and safely.
This entire book is filled with important safety information please read itcarefully.

2
CONTENTS
GENERATOR SAFETY ........................................................................................................................................................4
IMPORTANT SAFETY INFORMATION ...................................................................................................................................... 4
Operator Responsibility ...................................................................................................................................................... 4
Carbon Monoxide Hazards ..........................................................................................................................................4
Electric Shock Hazards.................................................................................................................................................4
Fire and Burn Hazards .................................................................................................................................................4
Refuel With Care .........................................................................................................................................................4
SAFETY LABEL LOCATIONS ............................................................................................................................................... 5
CONTROLS & FEATURES.........................................................................................................................................................6
COMPONENT & CONTROL LOCATIONS............................................................................................................................6
CONTROLS ................................................................................................................................................................................ 8
Fuel Valve Lever........................................................................................................................................................... 8
Choke Knob .................................................................................................................................................................8
Engine Switch ...............................................................................................................................................................8
CircuitBreaker............................................................................................................................................................. 8
FEATURES .......................................................................................................................................................................................... 9
Oil Alert System........................................................................................................................................................... 9
Ground Terminal .................................................................................................................................................................. 9
FuelGauge ..................................................................................................................................................................9
Volt Meter ...................................................................................................................................................................9
Hour Meter..................................................................................................................................................................9
BEFORE OPERATIO N ........................................................................................................................................................ 10
ARE YOU READY TO GET STARTED? ................................................................................................................................10
Knowledge ......................................................................................................................................................................... 10
IS YOUR GENERATOR READY TO GO?.............................................................................................................................10
Check the Engine.......................................................................................................................................................10
Check the Battery......................................................................................................................................................10
OPERATION .............................................................................................................................................................................11
SAFEOPERATING PRECAUTION .....................................................................................................................................11
STARTING THE ENGINE ................................................................................................................................................. 11
STOPPING THE ENGINE..................................................................................................................................................12
ACOPERATION ..............................................................................................................................................................13
AC Receptacle............................................................................................................................................................13
AC OUT PUT TERMINAL.................................................................................................................................................14
AC Applications .........................................................................................................................................................14
STANDYBY POWER ................................................................................................................................................................ 15
Connection to a Building’s Electrical System .............................................................................................................15
System Ground..........................................................................................................................................................15
Special Requirements................................................................................................................................................15
SERVICING YOUR GENERATOR ...........................................................................................................................................16
THE IMPORTANCE OF MAINTENANCE............................................................................................................................16
MAINTENANCE SAFETY ..................................................................................................................................................16

3
CONTENTS
Safety Precautions..................................................................................................................................................... 16
MAINTENANCE SCHEDULE ............................................................................................................................................ 17
REFUELING ............................................................................................................................................................................. 17
FUEL RECOMMENDATIONS .................................................................................................................................................. 18
Gasolines Containing Alcohol ....................................................................................................................................19
ENGINE OIL LEVEL CHECK ..............................................................................................................................................19
ENGINE OIL CHANGE .....................................................................................................................................................20
OIL FILTER CHANGE .......................................................................................................................................................20
ENGINE OILRECOMMENDATION...................................................................................................................................21
AIR CLEANER SERVICE....................................................................................................................................................21
FOAM AIRFILTER CLEANING .........................................................................................................................................22
SEDIMENT CAP CLEANING.............................................................................................................................................22
SPARK PLUG SERVICE.....................................................................................................................................................23
BATTERY SERVICE ................................................................................................................................................................... 24
BatteryRemoval .........................................................................................................................................................24
BatteryCharging.........................................................................................................................................................25
STORAGE ..............................................................................................................................................................................................................................26
STORAGE RECAUTION ............................................................................................................................................................ 26
Cleaning .............................................................................................................................................................................. 26
Fuel .................................................................................................................................................................................... 26
STORAGE PROCEDURE ........................................................................................................................................................... 27
STORAGE PRECAUTIONS ........................................................................................................................................................ 28
REMOVALFROM STORAGE............................................................................................................................................. 28
TRANSPORTING...............................................................................................................................................................29
TAKING CARE OF UNEXPECTED PROBLEMS ......................................................................................................................30
ENGINE PROBLEMS ........................................................................................................................................................ 30
Engine Will Not Start .................................................................................................................................................. 30
Engine Lacks Power ....................................................................................................................................................30
GENERATOR PROBLEMS ....................................................................................................................................................... 31
No Power at theAC Receptacles.................................................................................................................................31
TECHNICAL INFORMATION...................................................................................................................................................32
CARBURETOR MODIFICATION FOR HIGH ALTITUDE OPERATION................................................................................. 32
SPECIFICATIONS ..................................................................................................................................................................... 32
WIRING DIAGRAM..........................................................................................................................................................33

4
GENERATOR SAFETY
IMPORTANT SAFETY INFORMATION
This generators are designed for use with electrical equipment that has suitable power requirements. Other uses can
result in injury to the operator or damage to the generator and other property.
Most accidents canbeprevented ifyou follow all instructions inthis manual and onthe generator. The most common
hazards are discussed below, along with the best way to protect yourself and others.
OperatorResponsibility
 Know how to stop the generator quickly in case of emergency.
 Understand the use of all generator controls, output receptacles, and connections.
 Be sure that anyone who operates the generator receives proper instruction. Do not let children operate the generator
without parental supervision.
Carbon MonoxideHazards
 Exhaust contains poisonous carbon monoxide, a colorless, odorless gas. Breathing carbon monoxide can cause loss
of consciousness and may lead to death.
 If you run the generator in an area that is confined, or even partly enclosed area, the air you breathe could contain
dangerous amount of exhaust gas.
 Never run your generator inside a garage, house, or near open windows or doors.
Electric Shock Hazards
 The generator produces enough electric power to cause a serious shock or electrocution if misused.
 Using a generator or electrical appliance in wet conditions, such as rain or snow, or near apool or sprinkler system,
or when your hands are wet, could result in electrocution. Keep the generator dry.
 If the generator is stored outdoors, unprotected from the weather, check all of the electrical components on the
control panel before each use. Moisture or ice can cause a malfunction or short circuit in electrical
components that could result in electrocution.
 Do not connect to a building’s electrical system unless an isolation switch has been installed by a qualified electrician.
 Do not use the generator without protective switch-off device.
Fire and Burn Hazards
 The exhaust system gets hot enough to ignite some materials.
 Keep the generator at least 1 meter away from buildings and other equipment during operation.
 Do not enclose the generator in any structure.
 Keep flammable materials away from the generator
 The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Be careful
not to touch the muffler while it is hot. Let the engine cool before storing the generator indoors.
Refuel With Care
Gasoline is extremely flammable, and gasoline vapor can explode. Allow the engine to cool if the generator has been in
operation. Refuel only outdoors in a well ventilated area with the engine OFF. Do not overfill the fuel tank. Never smoke
near gasoline, and keep other flames and sparks away. Always store gasoline in an approved container. Make sure that
any spilled fuel has been wiped up before starting the engine.

5
GENERATOR SAFETY
SAFETY LABEL LOCATIONS
These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off
or becomes hard toread, contact your THIS servicing dealer for a placement.
 This generator is designed to give safe and dependable service if operated according to
instructions.
 Read and understand the Owner’s Manual before operating the generator. Failure to do so could
result in personal injury or equipment damage.
 Exhaust contains poisonous carbon monoxide, a colorless, odorless gas. Breathing carbon
monoxide can cause loss of consciousness and may lead to death.
 If you run the generator in an area that is confined, oreven partially enclosed area, the air you
breathe could contain a dangerous amount of exhaust gas.
 Never run your generator inside a garage, house or near open windows or doors.
 Do notconnect toa building’s electrical system unless an isolation switch has been installed by
a qualified electrician.
 Connections for standby power to abuilding ’s Electrical system must be made by a
qualified Electrician and must comply with all applicable laws and electrical codes. Improper
connections can allow electrical current from the generator tobackfeed into the utility lines.
Such back feed may electrocute utility company workers or others who contact the lines during
apower outage, and when utility power is restored, thegenerator may explode, burn,
or cause fires in the building’s electrical system.
 A hot exhaust system can cause serious burns. Avoid contact if the engine has been running.

6
CONTROLS & FEATURES
COMPONENT & CONTROL LOCATIONS
Use the illustrations on these pages to locate and identify the most frequently used controls.
CONTROL PANEL
LPG PORT
THE FIRST STAGE
REGULATOR
THE SECOND
STAGE REGULATOR
HOUR
METER
CIRCUIT
BREAKER
ENGINE
SWITCH
FUEL SELECTION SWITCH
AC RECEPTACLES

7
CONTROLS & FEATURES
CYLINDER
CRANIUM
AIR CLEANER
OIL TANK CAP
EMPTY FULL
OIL GAUGE
OIL LEVEL
DIPSTICK
BATTERY
OIL DRAIN TUBE
STARTER MOTOR

8
CONTROLS & FEATURES
CONTROLS
Fuel Valve Lever (When using gasoline)
 The fuel valve lever is located between the fuel tank and carburetor.
 The fuel valve lever must be in the ON position for the engine to run.
 After stopping the engine, turn the fuel valve lever to the OFF position.
Choke Knob
 The choke knob opens and closes the choke valve in the carburetor.
 The CLOSED position enriches the fuel mixture for starting a cold
engine.
 The OPEN position provides the correct fuel mixture for operation
after starting, and for restarting a warm engine.
Engine Switch
The engine switch controls the ignition system, and it operates the
electric starter.
FUEL VALVE LEVER
CHOKE KNOB

STOP -- Stops the engine. The engine switch key can be
removed/ inserted.
 RUN -- Running position.
 START -- Operates the electric starter.
Circuit Breaker
 The circuit breaker will automatically switch
OFF, if there is a short circuit or a significant
overload at the receptacles or output
terminals.
 The circuit breaker may be used to switch
the generator power ON or OFF.
ON
OFF
Engine Switch
ON
OFF
STAR
CIRCUIT
BREAKER
OPEN
CLOSED
Fuel Selection Switch
 When using gasoline, turn the switch to "GAS"
 When using LPG,turn the switch to "LPG"
FUEL SELECTION SWITCH

9
EMPTY
FULL
CONTROLS & FEATURES
FEATURES
Oil Alert System
The Oil Alert system is designed to prevent engine damage caused by aninsufficient amount of oil in the
crankcase. Before the oil level in the crankcase can fall below a safe limit, the Oil Alert system will automatically stop the
engine
(theengine switch will remain in the RUN position).
If the engine stops and will not restart, check the engine oil level (see Page 20)before trouble shooting in other areas.
Ground Terminal
The ground terminal is connected tothe frame ofthe generator, themetal noncurrent carrying parts of thegenerator,
and the ground terminals of each receptacle.
Before using the ground terminal, consult a qualified electrician, electrical inspector, or local agency having jurisdiction
for local codes or ordinances that apply to the intended use of the generator.
Attention ! It is compulsorily to make protective earthing before
operating the generator. Protective earthing must correspond to
Rules for Installing Electrical Facilities.
GROUND
TERMINAL
Earthing devices and grounding conductors must be selected in accordance
with chapters 1.7 and 1.8 of Rules for Installing Electrical Facilities.
Usually, copper grounding conductor needed of minimum 4mm² section.
Fuel Gauge
The fuel gauge is a mechanical device that measures the fuel level in the
tank. The red indicator in the window will reflect the level in relation
to full or empty. To provide increased operating time, start with a full
tank before beginning operation. Check the fuel level with the generator
on a level surface. Always refuel with the engine OFF and cool.
OIL GAUGE
FUEL TANK CAP
Hour Meter
The hour meter indicates the hours the generator has been operated.
Use it to determine when scheduled maintenance should be
Performed
.
Hour Meter

10
BEFORE OPERATION
ARE YOU READY TO GET STARTED?
Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury.
Knowledge
Read and understand this manual. Know what the controls do and how to operate them.
Familiarize yourself with the generator and its operation before you begin using it. Know how to quickly shut off
the generator in case of an emergency.
If the generator is being used to power appliances, be sure that they do not exceed the generator’s load rating .
IS YOUR GENERATOR READY TO GO?
For your safety, and to maximize the service life of your equipment, it is very important to take a few moments before
you operate the generator to check its condition. Be sure to take care of any problem you find, or have your servicing
To prevent a possible fire, keep the generator at least 1 meter away from building walls and other equipment during
operation. Do not place flammable objects close to the engine.
Before beginning your preoperation checks, be sure the generator is on a level surface and the engine switch is in the
OFF position.
Check the Engine
Check the oillevel (see page 19). A low oil level will cause the Oil Alert system to shut down the engine.
Check the air cleaner (see page 21).A dirty air cleaner element will restrict air flow to the carburetor, reducing engine
and generatorperformance.
Check the fuel level (see page 18).Starting with a full tank will help to eliminate or reduce operating interruptions for
refueling.
Check theBattery
Check the fuel electrolyte level (see page 24). If the electrolyte level is
below the LOWER level, sulfation and battery plate damage will occur.
BATTERY

11
OPERATION
SAFE OPERATING PRECAUTIONS
Before operating the generator for the first time, please review the GENERATOR SAFETY section and the chapter titled
BEFORE OPERATION.
For your safety, do not operate the generator in an enclosed area such as a garage. Your generator’s exhaust contains
poisonous carbon monoxide gas that can collect rapidly in an enclosed area and cause illness or death.
Before connecting an AC appliance or power cord to the generator:
 Use grounded 3 prong extension cords for single phase generator and 5 prong extension cords for three generator,
tools, and appliances, or double insulated tools and appliances.

Inspect cords and plugs, and replace if damaged.
 Make sure that the appliance is in good working order. Faulty appliances or power cords can create a potential for
electric shock.
 Make sure the electrical rating of the tool or appliance does not exceed that of the generator. Never exceed the
maximum power rating of the generator. Power levels between rated and maximum may be used for no more than
30 minutes.
 Operate the generator at least 1 meter away from buildings and other equipment.
 Do not operate the generator in an enclosed structure.
ON
STARTING THE ENGINE
1. Make sure that the circuit breaker is in the OFF position.
The generator maybe hard to startif a load is connected.
OFF
CIRCUIT
BREAKER
2-1. Turn the fuel valve lever to the ON position
(when using gasoline).
OFF
ON
FUEL VALVE LEVER
2-2. Connect LPG (when using gasoline)
 Connect the LPG connecting pipe to the
LPG port of generator and tighten it;
 Connect the LPG connecting pipe to the
LPG tank and tighten it;
 Open the fuel valve switch on LPG tank.
2-1. Gasoline
2-2. LPG

12
CLOSED
CHOKE KNOB
OPEN
CHOKE K
RUN
STOP
STAR
ENGINE SWITCH
OPERATION
3. Pull the choke knob totheCLOSED position tostart a cold engine.
Leave the choke knob in the OPEN position to restart a warm engine.
4. Start the engine. Turn the engine switch to the START position, and hold
it there until theengine starts. When the engine starts, release the key,
allowing the switch to return to the RUN position.
If the engine fails to start within 5 seconds, release the key, and wait at
least 10 seconds before operating the starter again.
Using the electric starter for more than 5 seconds at a time will Overheat the starter motor and can damage it.
5. If the choke knob was pulled to the CLOSED position to start the engine,
gradually move it to the OPEN position as the engine warms up.
6. Generator needs to operate for 3-5 minutes without load, then
it can out putpower.
NOB
STOPPING THEENGINE
To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use
the followingprocedure.
1.
Move the circuit breaker to the OFF position.
ON
OFF
CIRCUIT
BREAKER
NOTICE

13
ENGINE SWICH
STOP RUN STAR
OPERATION
2. Turn the engine switch to the OFF position (when using gasoline).
3-2. Turn the fuel valve lever to the OFF position(when using
gasoline).
ON
OFF
AC OPERATION
FUEL VALVE LEVER
If an appliance beings to operate abnormally, becomes sluggish or stops suddenly, turn it off immediately. Disconnect the
appliance, and determine whether the problem is in the appliance or the rated load capacity of the generator has been
exceeded.
Substantial over loading may damage the generator.Marginal over loading may shorten the service life of the generator.
ACReceptacle
1. Start the engine (see page11).
2. Switch ON the circuit breaker.
3. Plug in the appliance.
Most motorized appliances require more
than their rated wattage for startup.
CIRCUIT
BREAKER
ON
OFF
NOTICE
3-1. Turn off the fuel valve on LPG tank (when using LPG).

14
OPERATION
AC Applications
Before connecting an appliance or power cord to the generator:
 Make sure that it is in good working order. Faulty appliances or Power cords can create a potential for electrical
shock.
 If an appliance begins to operate abnormally, becomes sluggish, or stops suddenly, turn it
off immediately. Disconnect the appliance, and determine whether the problem is the appliance or the rated
load capacity of the generator has been exceeded.
 Make sure that the electrical rating of the tool or appliance does not exceed that of the generator. Never exceed
the maximum power rating of the generator. Power levels between rated and maximum may be used for no more
than 30 minutes.
Substantial overloading will open the circuit breaker. Exceeding the time limit for maximum power operation or slightly
overloading the generator may not switch the circuit breaker OFF, but will shorten the service life of the generator.
Limit operation requiring maximum power to 30 minutes.
Maximum power is:
60Hz 15kVA (GAS);
1 3.5 kVA (LPG);
For continuous operation (longer than 30 minutes), do not exceed the rated power.
Rated power is:
60Hz 12kVA(GAS);
1 1 kVA (LPG);
NOTICE
High Altitude Operation
At high altitude, the standard carburetor air/fuel mixture will be too rich. Performance will decrease, and fuel
consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting. Operation at an
altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.
High altitude performance can be improved by specific
modifications to the carburetor. If you always operate your generator at altitudes above 5,000 feet
(1,500 meters), have your dealer perform this carburetor modification. This engine, when operated at high altitude with
the carburetor modifications for high altitude use, will meet each emission standard throughout its useful life. Even with
carburetor modification, engine horsepower will decrease about 3.5% for each 1,000-foot (300-meter) increase in
altitude. The effect of altitude on horsepower will be greater than this if no carburetor modification is made.

15
OPERATION
The total power requirements (VA) of all appliances connected must be considered. Appliance and power tool
manufacturers usually list rating information near the model number or serial number.
STANDBY POWER
Connections to a Building’s Electrical System
Your generator can supply power to a building’s electrical system. If the generator will be used as an alternative to
utility company power, an isolation switch must be installed to disconnect the utility lines from the building when the
generator is connected. Installation must be performed by a qualified electrician and must comply with all applicable laws
and electrical codes.
In some areas, generators are required by law to be registered with local utility companies. Check local regulations for
proper registration and use procedures.
System Ground
THIS generators have a system ground that connects the generator frame components to the ground terminals in the
AC output receptacles. The system ground is not connected to the AC neutral wire. If the generator is
tested with a receptacle tester, it will not show the same ground circuit condition as for a home receptacle.

Special Requirements
In some areas, generators are required to be registered with local utility companies.
If the generator is usedat a construction site, there may be additional regulations that must be observed.

16
SERVICING YOUR GENERATOR
THE IMPORTANCE OF MAINTENANCE
Good maintenance is essential for safe, economical, and trouble free operation. It will also help reduce air pollution.
To help you properly care for your generator, the following pages include a maintenance schedule, routine inspection
procedures, and simple maintenance procedures using basic hand tools. Other service tasks that are more difficult or
require special tools are best handled
by professionals and are normally performed by a THIS
technician or other qualified mechanic.
The maintenance schedule applies to normal operating
conditions. If you operate your generator under
unusual conditions,
such as sustained high load or high temperature operation, or use it in dusty
conditions, consult your servicing dealer for recommendations applicable to your individual needs and use.
Remember that your servicing dealer knows your generator best and is fully equipped to maintain and repair it.
MAINTENANCE SAFETY
Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that
can arise in performing maintenance. Only you can decide whether or not you should perform a given task.
Safety Precautions
Make sure the engine is off before you begin any maintenance or repairs. This will eliminate several potential hazards:
 Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate the engine.
 Burns from hot parts.
Let the engine and exhaust system cool before touching.
 Injury from moving parts.
Do not run the engine unless instructed to do so.

17
SERVICING YOUR GENERATOR
 Read the instructions before you begin, and make sure you have the tools and skills required.
 To reduce the possibility of fire or explosion, be careful when working around gasoline. Use only a nonflammable
solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel related parts.
MAINTENANCE SCHEDULE
NOTE: (*) Replace the paper element only.
(1) Service more frequently when used industry areas.
(2) These items should be serviced by your servicing dealer, unless you have the proper tools and are
mechanically proficient. Refer to our shop manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Failure to follow this maintenance schedule could result in nonwarrantable failures.
REFUELING
With the engine stopped, check the fuel gauge. Refill the fuel tank if the fuel level is low.
*

18
SERVICING YOUR GENERATOR
EMPTY FULL
OIL GAUGE
OIL TANK CAP
Refuel in a well ventilated area before starting the engine. If the engine has been running, allow it to cool. Refuel
carefully to avoid spilling fuel. Do not fill the fuel tank above the upper limit mark (red) on the fuel strainer.
Never refuel the engine inside a building where gasoline fumes may reach flames or sparks. Keep gasoline away from
appliance pilot lights, barbecues, electric appliances, power tools, etc.
Spilled fuel is not only a fire hazard, it causes environmental damage. Wipe up spills immediately.
Fuel can damage paint and plastic. Be careful not to spill fuel when filling your fuel tank. Damage caused by spilled fuel
is not covered underwarranty.
NOTE:
Gasoline spoils very quickly depending on factors such as light, exposure, temperature and time.
In worst cases, gasoline can be contaminated within 30days.
Using contaminated gasoline can seriously damage the engine (carburetor clogged, valve stuck).
Such damage due to spoiled fuel is disallowed from coverage by the warranty.
To avoid this please strictly follow these recommendations:
 Only use specified gasoline.
 Use fresh and cleangasoline.
 To slow deterioration, keep gasoline in a certified fuel container.
 If long storage (more than 30 days) is foreseen, drain fuel tank and carburetor (see page 27).
FUEL RECOMMENDATIONS
Use automotive unleaded gasoline with a Research Octane Number of 91 or higher (a Pump Octane Number of 86 or
higher).
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
NOTICE

19
SERVICING YOUR GENERATOR
Gasolines ContainingAlcohol
If you decide to use a gasoline containing alcohol (gasohol), besure it’s octane rating is at least as high as that
recommended bythis.There are two types of ‘‘gasohol’’: one containing ethanol, and the other containing methanol. Do
not use gasohol that contains more than 10% ethanol. Donot use gasoline containing methanol (methyl orwood
alcohol) that does not also contain cosolvents and corrosion inhibitors for methanol. Never use gasoline containing more
than 5% methanol, even if it has cosolvents and corrosion inhibitors.
NOTE:
 Fuel system damage or engine performance problems resulting from the use of fuels that contain alcohol is not
covered under the warranty.
THIS cannot endorse the use of fuels containing methanol since evidence of their suitability is as yet incomplete.
 Before buying fuel from an unfamiliar station, try to find out If the fuel contains alcohol, if it does, confirm the type
and percentage of alcoholused.
If you notice any undesirable operating symptoms while using a gasoline that contains alcohol, or one that you think
contains alcohol, switch to a gasoline that you know does not contain alcohol.
ENGINE OIL LEVELCHECK
Check the engine oil level with the generator on a level surface and the engine stopped.
1. Remove the oil level dipstick and wipe it clean.
2. Fully insert the dipstick, then remove it to check the oil level.
3. If the level is near or below the lower limit mark on the dipstick, open the
maintenance cover to access the oil filler cap. Remove the oil filler cap, and
fill with the recommended oil to the upper limit mark.
4. Reinstall the oil level dipstick and filler cap.
OIL LEVEL
DIPSTICK
OIL FILLER CAP
The Oil Alert system will automatically stop the engine before the oil level falls below safe limits. However, to avoid the
inconvenience of an unexpected shutdown, check the oil level regularly.