PumpSpy PSO1000 User manual

FRONT
COVER
SUMP PUMP
SMART OUTLET
LIMITED 3YEAR WARRANTY
PUMP SPY
®
Your
Sump Pump
plugs into the
top outlet
Additional
outlet for
backup pump,
dehumidier,
etc.
Connection for
High Water Sensor
Outlet
ring glows
to show WiFi
connection
and pump
status
Requires WiFi
WHAT THIS WARRANTY COVERS
When used and maintained in normal use and in accordance
with the Installation and Operating Instructions, your PumpSpy®
product is warranted against original defects in material and
workmanship for a full three years from date of purchase (the
“Warranty Period”). During the warranty period, PumpSpy will
repair or replace at no cost to you, to correct such defects in
products found upon examination by PumpSpy to be defective in
materials or workmanship.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover use of the product in a non-
residential application, improper installation and/or improper
maintenance of the product, damage due to misuse, acts of God,
nature, vandalism or other acts beyond the control of PumpSpy,
owner’s acts or omissions, use outside the country in which the
product was initially purchased and resales of the product by the
original owner.This warranty does not cover pick up, delivery,
transportation or house calls. However, if you mail your product
to PumpSpy for warranty service, cost of shipping will be paid
one way.This warranty does not cover products purchased from
a party that is not an authorized retailer, dealer, or distributor of
PumpSpy products.
OTHER IMPORTANT TERMS
This warranty is not transferable and may not be assigned.This
warranty shall be governed and construed under the laws of
the state of Ohio.The warranty period will not be extended
by any replacement or repair performed under this warranty.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND
REMEDY PROVIDED BY PumpSpy.. ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES
OR MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT WILL PumpSpy
BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE
TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER
WHETHER BASED IN CONTRACT, NEGLIGENCE,TORT
OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY
CAUSE WHATSOEVER. Some states do not allow for the
exclusion of consequential damages, so the above exclusion may
not apply to you. This warranty gives you specic rights. You may
also have others that vary state to state.
WiFi Conguration
Button
34000 Lear Industrial Pkwy, Avon, OH 44011•www.pumpspy.com
© 2016 PumpSpy Technology, LLC
This device complies with part 15 of the FCC and Industry
Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1)this device may
not cause harmful interference, and (2)this device must
accept any interference received, including interference
that may cause undesired operation. FCC NOTE:The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modications
to this equipment. Such modications could void the
user’s authority to operate the equipment. NOTE:This
equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.This equipment generates, uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
Important note: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or
the device is permitted.Any change to the antenna or
the device could result in the device exceeding the RF
exposure requirements and void user’s warranty.
Thank you for purchasing a
PumpSpy Sump Pump Smart Outlet!

Inspect the power outlet you intend to plug your
PumpSpy Smart Outlet into. If there is any damage
or excessive wear on the outlet, please contact an
electrician.
To reduce any risks of damage please read and understand any
safety and operation instructions included with the sump pump
and other devices you wish to use with your PumpSpy Smart
Outlet.
Do not plug a sump pump or any other device into the
PumpSpy Smart Outlet if the device’s ground prong has been
removed or damaged.
Do not plug a sump pump or any other device into the
PumpSpy Smart Outlet if the device’s power cord is cut or
damaged.
Do not attempt to disassemble or open the PumpSpy Smart
Outlet. There are no eld serviceable parts or repair options.
UNPACKING
Inspect this device before beginning installation. Occasionally,
products are damaged during shipping. If the outlet or any
components are damaged, contact PumpSpy for a replacement
at [e-mail] or 515.999.6935.
INSTALLATION
BEFORE INSTALLING THE PUMPSPY SUMP PUMP
SMART OUTLET, VERIFY THAT YOUR SUMP PUMP
IS IN GOOD WORKING CONDITION! REPLACE IF
NECESSARY!
1. CONNECT THE SMART OUTLETTOYOUR WI-FI
NETWORK AND INSTALL THE PUMPSPY APP ON
YOUR DEVICE. SEE ENCLOSED CONNECTION
GUIDE.
2. UNPLUG YOUR SUMP PUMP AND ANY OTHER
CORDS FROM THE WALL A/C OUTLET
3. PLUG THE SMART OUTLET INTO WALL A/C
OUTLET
A. PumpSpy recommends removing the outlet cover screw and
then securing the Smart Outlet to the power outlet with the
included mounting screw. If removing the screw is not possible
or desired, make sure the outlet is rmly plugged into the power
outlet and is ush as possible with the wall.
B.The PumpSpy Smart Outlet is not designed to be used
with extension cords or power strips. If you have multiple
devices that require the use of a power strip, a power strip
can be connected to the lower plug outlet on the Smart Outlet.
4. CONNECT OTHER DEVICES TO THE LOWER
STANDARD OUTLET, IF APPLICABLE.
5. INSTALL THE HIGH WATER SENSOR,
CLAMPING TO THE DISCHARGE PIPE OFYOUR
SUMP PUMP.
A. Adjust the position of the mounting bracket so the high
water sensor does not interfere with the operation of the
main sump pump switch.
B. Adjust the height of the mounting bracket so the high
water sensor is activated when the water level reaches
approx. 1” higher than the “on” level of your main sump
pump.
C. If you have a secondary sump pump/battery backup pump,
make sure the high water sensor is activated BETWEEN the
“on” level of the main sump pump and the “on” level of the
secondary/backup pump.
PUMPSPY HIGHLY RECOMMENDSTHAT YOU ALWAYS
HAVE 2 WORKING SUMP PUMPS INSTALLED IN YOUR
HOME, ONE OF WHICH CAN OPERATE IN THE EVENT
OF A POWER OUTAGE.THE PUMPSPY SUMP PUMP
SMART OUTLET WILL NOT OPERATE YOUR SUMP PUMP
IN THE EVENT OF A POWER OUTAGE.ALTHOUGH
PUMPSPY WILL SEND YOU ALERTS WHEN YOUR PUMP
HAS AN ISSUE,WE RECOMMEND HAVING A BACKUP
PUMP THAT CANTAKE OVER PUMPING DUTY UNTIL
REPAIRS CAN BE COMPLETED.
The High Water Sensor
be mounted 1 ” higher than
the “on” level of
main sump pump
IMPORTANT!
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
SPECIFICATIONS
WARNING
The PumpSpy Smart Outlet is for
residential indoor use only.
To reduce the risk of electrical shock, this device
must be properly grounded in accordance with
the National Electric Code (NEC)and all
applicable state and local codes and ordinances.
The receptacle used with the PumpSpy
®Smart Outlet should
be protected with a Ground Fault Circuit Interrupter (GFCI).
Never remove the ground prong from the PumpSpy Smart
Outlet, or use an adapter that eliminates the ground prong.
Always plug your PumpSpy Smart Outlet directly into your wall
power outlet. Do not use an extension cord. Extension cords
could present a safety hazard if not properly sized, become
damaged or the connection falls into the sump pit.
Conrm that your PumpSpy Smart Outlet is completely
plugged into your wall power outlet and secured with the
included hardware. Your device should sit as ush as possible
with the wall outlet. If it seems loose, please contact an
electrician.
POWER SUPPLY REQUIREMENTS
INPUT 120V, 15A, 60Hz
OUTPUT 120V, 15A, 60Hz
Wi-Fi Radio 802.11 a/b/g/n 2.4 GHz
Operating Temperature 0 to 50 C
Storage Temperature 0 to 70 C
Relative Humidity 0 to 90%