Pura URFMBSM User manual

TM
URFMBSM
Urban Floor Standing Bath Shower Mixer
BS01551125. ZX
III Installation Diagram:
IV Installing Steps (As shown in figure 1~13):
Ø12 Hole
Protection Cover
Inlet Base
Hexnut
Flat Shim
Spring Shim
Expansion Bolt
I Installation Notice
1. Install water supply lines in accordance with this manual.
2. The waste should be installed in the location of the mixer.
3. Install the tap only after the completion of interior house
decoration in case paint or other chemicals erode the
chrome surface.
4. Clean pipes to get rid of mud, sand or other debris blocked
in pipes.
5. Check whether the threads can be matched. Otherwise, too
much force applied to the wrench will damage the mixer.
6. After installation, check all the joints to make sure they are
firmly connected. Turn on and off repeatedly to ensure
there are no leaks around the joints.
7. Pass the manual to the user.
II Operation Notice
1. The product is used between water pressure 1.0 - 4 bar,
water temperature 4~90°C.
2. Do not hang heavy things on the mixer.
3. Always clean the surface of chrome to keep it bright.
Attention: Please do not use inappropriate tools such as
sharp brushes, rough sponges, scouring pads or corrosive
detergent to clean the tap, and we do not recommend
that you use any household detergent, because its
formula may damage the chrome. Please clean the with a
wet cloth and soapy water after each time of usage. Then
rinse the soap off with clean water and dry with a soft
cotton cloth.
4. When the room temperature drops to below 0°C, take
necessary measures (such measures as keeping the tap
warm and closing windows) to prevent the tap from
being frozen or even broken.
5. You should open the cold and hot water in turn and adjust
the temperature before washing or showering. To avoid
scalding, regulate the water temperature before washing
or showering and do not touch the hot part of the mixer.
6. Do not disassemble the product unless you are an expert.
Drill 4 Ø12 holes on the floor in
accordance with the inlet base
(make sure that the printed mark
for hot water faces to the bathtub).
Install 4 expansion bolts to the
inlet base and tighten them
with hexnuts.

TM
Spirit Level
Flange
End Cap
Hot-water Supply Line
Cold-water Supply Line
Wrench
Locking Screw
Flow Water
Flow Water
Horizontal Level Detection
Tap Body
Water Inlet Pipe
Protection Cover
Shroud
Longitudinal Level Detection
Insert the expansion bolts into the holes on the floor (attention:
the printed mark for hot water faces to the bathtub). Check the
upper surface of the inlet base by using a spirit level. Make sure
that the inlet base is level. Then fix with hexnuts.
Install the cold and hot supply
lines and connect them to the
inlet base. Make sure that the
hot water supply faces to the
bathtub and the cold water
supply is at the back . (attention
to hot supply from the front and
cold supply from the back).
Wrap the PTFE tape around the
threads. Flow water to get rid of
mud, sand and other debris
blocked in pipes. Then take off
the protection cover and insert
the end caps into the outlet of
inlet base. Tighten them with a
flange.
Flow water for pressure test
and make sure that there is
no leakage occuring .
Unscrew the locking
screws and remove the
flange and end caps.
Put on the protection cover and fit the ceramic tiles
(attention: the tiles should be kept at the same height as
or a bit higher than the top of protection sheath.
Take off the protection cover.
Remove the protection
cover from the water inlet
pipe of the tap body (pay
special attention to the
surface of the tap body to
avoid scratching). Then fix
the flange firmly on the tap
body with locking screws.
URFMBSM
Urban Floor Standing Bath Shower Mixer
4.0 bar

Pura Bathrooms ltd. 15 Millbrook Industrial Estate, Sybron Way, Crowborough, East Sussex. TN6 3DU
www.purabathrooms.com Technical Helpline: 01892 611240
90° Elbow
Insert the water inlet
pipe vertically into the
outlet of the inlet base.
Then connect the flange
and inlet base with
locking screws. Tighten
them with wrench. Put
on the escutcheon close
to the floor.
Screw the 90° elbow into the faucet body.
Connect the handshower and faucet
body with flexible hose.
After installation, run water for
inspection. The figure is for the
case when the handle is turned
on.