Pure Lighting Stratus RGB User manual

1
ELECTRICAL KNOCKOUT
Hole Identification
Top View of Housing
MOUNTING BRACKET KNOCKOUT
2: Tap the anchors onto the marked locations up to the threaded
portion with a hammer.
3: Screw the threaded portion of the anchors in with a Phillips
screwdriver.
NOTE: Use the fixture as a template by aligning it against the
wall, ceiling, and the electrical conduit(s), and mark the
necessary holes for installation. Punch out the marked knockout
holes. Refer to the hole identification drawing below for proper
installation.
ANCHOR
WALL
2
3
B
1: Determine the location where the fixture will be installed. In most cases, fixture will be installed in either a flush ceiling or in a
in-depth cove installation.
NOTE: If installing fixture in a in-depth cove location the housing lip does not have to be used. Loosen and
remove the four Phillips screws and pull the housing lip off.
HOUSING
LIP
DRYWALL
5.5"
FIXTURE
1
FIXTURE
7"
MINIMUM
10"
COVE
CEILING
1
6"
NOMINAL
A
FLUSH CEILING INSTALLATION IN-DEPTH COVE INSTALLATION
Install the Fixture
SAVE THESE INSTRUCTIONS!
- This product is suitable for damp locations or outdoor
under awning.
- This instruction shows a typical installation.
- This product is ETL listed.
IMPORTANT INFORMATION
PART# SH_-SP_-RGB
© 2016 Pure Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: [phone]
Fax: [phone]
www.purelighting.com
[email protected]
Stratus RGB
Installation Instruction
INS# STRATUS_RGB_2

10: Insert the top portion of the LED panel into the bracket slot.
Slide the bottom portions spring clip onto the fixture housing
lip and snap in.
11: Follow wiring diagram on page 4 for proper wiring.
2
LED PANEL
SPRING CLIP
COVE CEILING
TEXTURED WALL
BRACKET SLOT
10
FIXTURE
HOUSING LIP
10
F
7: Use the additional provided joiner bracket, when joining two
fixtures together.
8: Follow step 1 through 7 to install the remaining fixtures.
9: Make all the proper wire connection following the wiring
diagram on page 4.
JOINER
BRACKET
ONE HOUSING
SECOND HOUSING
8
7
E
5: Align the fixture to the wall bracket and secure to the wall
bracket with the lock nut and washer.
6: OPTIONAL: Secure the bracket to the ceiling with the #8
screws provided.
WALL BRACKET
COVE CEILING
COVE CEILING
10"
7"
MINIMUM
TEXTURED WALL PHILLIPS SCREW
5
HOUSING
6
LOCK NUT & WASHER
D
4: Mount each wall bracket onto the anchors and secure it with
the provided four #8 screws.
#8 SCREW
4
ANCHOR
WALL
BRACKET
4
CEILING
WALL
C

3
NOTE: If the fixture was installed against drywall, plaster and then
sand the housing lip to complete the installation.
TEXTURED WALL
HOUSING LIP
DRYWALL
ADD PLASTER,
SAND, AND PAINT
FLUSH CEILING
I
13: To access the inside of fixture, you can use a flat head screw
driver to pull the LED panel out.
LED
PANEL
COVE CEILING
TEXTURED WALL
13
SCREW
DRIVER
H
12: Secure the end caps to the housing with the four screws
provided.
HOUSING
END CAP
12
SCREW
G

4
Stratus
BLUE-
BLUE+
GREEN-
GREEN+
RED-
RED+
DVR-90
GROUP 1+ GROUP 1- GROUP 2+ GROUP 2- GROUP 3+ GROUP 3- GROUP 4+ GROUP 4- NTC+ NTC-
MAX / VDC+ 32V / VDC- EXT in - EXT in + DALI in + DALI in - DALI out + DALI out - DMX in + DMX in -
DMX in shield
LEDSync out + LEDSync out - LEDSync shield
+ RED
LOAD - BLUE
INPUT POWER
(120VAC)
NEUTRAL
LED Board
BLACK LINE WHITE
LINE
24VDC
+ -
LINE
N L
GROUND
+24 VDC
DATA +
DATA -
GROUND
CDP
CONTROLLER
CONTROLLER
POWER SUPPLY
DMX CABLE (BELDEN #9841)
POWER SUPPLY
Parallel Connection to the other LED Boards
DVR-90
MAX / VDC+ 32V / VDC- EXT in - EXT in + DALI in + DALI in - DALI out + DALI out - DMX in + DMX in -
DMX in shield
LEDSync out + LEDSync out - LEDSync shield
Stratus RGB
General Wiring Diagram
24VDC120VAC
DC+
DC-
DVR-90
MAX / VDC+ 32V / VDC- EXT in - EXT in + DALI in + DALI in - DALI out + DALI out - DMX in + DMX in -
DMX in shield
LEDSync out + LEDSync out - LEDSync shield