PuzzleSounds GREEN RINGER User manual

GREEN RINGER

GREEN RINGER
We hope you enjoy your new GREEN RINGER! In this manual, you will
find documentation and guidelines helpful to put it together.
Here we have put together a few links that detail some of the aspects
explained in this manual and that we think you can find helpful:
Kit & PuzzleKit general manual
Reading resistor and capacitor values
Also, in our blog you can find multiple articles regarding tips for
soldering, more in-depth posts about resistors and capacitors…
Check it out!

GREEN RINGER
Bill Of Materials
Resistors (13)
1
R1
1.5M
1
R2
560k
1
R3
160k
1
R4
18k
1
R5
6.2k
3
R6, R9, R12
10k
2
R7, R8
68k
2
R10, R11
22k
1
R13
47k
Capacitors (5)
3
C1, C2, C3
47n
1
C4
100n
1
C5
100u
(electrolytic)
Transistors (3)
2 Q1, Q2 2N5088
1 Q3 2N3906
Diodes (2)
2 D1, D2 1N914/1N4148
Other (2)
1 DP 1N4007
1 RON 1k

GREEN RINGER
Part Placement

GREEN RINGER
STEP BY STEP GUIDE

STEP 1 –Resistors and diodes
Place the resistors and diodes. If you have
troubles reading the values, check out our
“Reading Part Values” tutorial.
Resistors (13)
1
R1
1.5M
1
R2
560k
1
R3
160k
1
R4
18k
1
R5
6.2k
3
R6, R9, R12
10k
2
R7, R8
68k
2
R10, R11
22k
1
R13
47k
Diodes (2)
2 D1, D2 1N914/1N4148
Other (2)
1 DP 1N4007
1 RON 1k

STEP 2 –Pin header
Then, connect the 6 pin header:

STEP 3 –Capacitors and Transistors
Solder the capacitors and transistors. If you have
troubles reading the values, check out our
“Reading Part Values” tutorial. Pay attention to the
orientation, as well as to the polarity for
electrolytic capacitors.
Capacitors (5)
3
C1, C2, C3
47n
1
C4
100n
1
C5
100u
(electrolytic)
Transistors (3)
2 Q1, Q2 2N5088
1 Q3 2N3906

STEP 4 –LED and Battery Clip
Solder two wires to the LED
connection (red to the “+” sign).
Then, solder then to the LED (the red
wire is connected to the longer pin).
Solder the battery clip, connecting the red wire to the “+” sign:

STEP 5 –DC Power Jack wires
Solder three wires (about 5cm each) to the DC connection as shown (don’t solder
anything to the other end yet!):

STEP 6 –Audio Jacks
Now, solder the audio jacks to the
board (DC, battery and led wires are
not present to make it clearer):
Then place the board inside the
enclosure:

STEP 7 –DC Power Jack
First of all, insert the DC jack in the enclosure and tighten the
nut:
Then, solder the three wires from the DC connector in the
board to the DC jack as follows:

STEP 8 –3PDT
A – Solder the pin to the adapter
Pay attention, the pins and the 3PDT
must be soldered to the same side of
the PCB adapter (the one labeled
“buttons and 3PDT on this side”).
B – Solder the 3PDT
Now solder the 3PDT to the PCB and
remove all the nuts but one, that should
be set at a middle height:

C – Solder the 3PDT directly to the board (optional)
If you prefer to solder the 3PDT directly
to the board, you can wire it as shown in
the schematic. We recommend to use the
provided 3PDT PCB adapter to make the
soldering easier.

STEP 9 –Connect the 3PDT
STEP 10 –Your pedal is finished!
By now you should have a fully functional effect pedal, we
hope you enjoy it!