PW 2231-12G User manual

4 1/2"O.D. PORTABLE PRACTICE ROUND SOCCER GOALS
6'6" H x 12' W
#2231-12G STEEL - WITH END FRAMES - 6'6" H x 12' W (805 LBS) PER SET
#2231-12A ALUMINUM - WITH END FRAMES - 6'6" H x 12' W (468 LBS) PER SET
SPECIFICATIONS:
NCAA soccer goal which provides a 6'6" H x 12' W front inside opening.
Crossbar and Uprights - a single length of 4 1/2" O.D. steel or aluminum tubing, powder coated white.
Crossbar is bolted to uprights.
All hardware is zinc-plated or Stainless Steel for long, rust free service.
Warranty period: 10 years
`
INSTALLATION:
Lay Upright/Corner Assemblies 24' apart parallel to each other on the ground with drilled pipe stubs 1.
facing up
Assemble crossbar to upright/corner assemblies with 3/8"-16 x 4" Button Head Bolts and Barrel 2.
nuts.
Sleeve a T-fitting onto the bottom leg of net support. Make sure set 3. screws will face up.
Insert net supports over 2" O.D. drilled inner sleeve stubs on corner assembly units4.
Align holes provided and attach with 3/8" x 3" hex head bolts5.
Attach spreader pipe between net supports. Insert spreader pipe into T-fittings and align holes, 6.
bolt through with 3/8" x 3-1/2" hex head bolts and tighten. NOTE: Position spreader pipe as far
back on long leg as possible and tighten 3/8" set screws with hex key
Tighten all bolts and set screws, cut and peen any excess threads7.
Carefully rotate goal into upright position. Repeat steps for other goal8.
Bolt Adjustable Wheel Bracket & Pnuematic Wheels in drilled hole locations
9.
ANCHORING SYSTEM (AUGER ANCHOR)
1. Connect chain to portable goal. Connect opposite end to auger. Pull chain tight then stick auger in
ground surface at an slight angle away from goal. (See Page 5, Auger Picture) Twist auger all the way in-
ground so the top hook/chain are slightly exposed.
SPEC 2231-12A-12G
PRODUCT NAME
MODEL NO.
Date: 7/26/2017
Rev: A
Drawn: BDYE
Sheet: 1 of 5
SOCCER GOAL
*OPTIONAL TRANSPORT ASSEMBLY*

DETAIL-X
SHT.#3
DETAIL-Y
SHT.#3
DETAIL-Z
SHT.#4
ISOMETRIC
2
6
5
3
3
4
6
1
7
BOM
ITEM
NO. PART NUMBER DESCRIPTION QTY.
1 SAS-500-2231-6'6-12A,18A RIGHT UPRIGHT 2
2 SAS-500-2231-6'6-12A,18A LEFT UPRIGHT 2
3 SAS-501-2200-G 2 7/8"x 3/16" WALL TEE FITTING 4
4 SAS-516-2200-8341 TRANSPORT SYSTEM ASSY 4
5 RT-011-2230-31-12' CROSSBAR 2
6 RT-002-2200-12G,18G-6.6 NET SUPPORT TUBE 4
7 RT-038-2200-144G SPREADER PIPE 2
8 HWBN381 3/8"-16 x 1" BUTTON HEAD BARREL NUT 8
9 HWBH384 3/8"-16 x 4" BUTTON HEAD BOLT 8
10 HWHB383 3/8"x16 x 3" SS HEX BOLT 8
11 HWLN38 3/8"-16 LOCK NUT 12
12 HWHB38312 3/8-16 X 3 1/2 GR5 HEX BOLT ZINC 4
13 HWSC3858 3/8"-16 x 5/8" SET SCREW 8
14 HWHB12312 1/2-13x3.5 GR5 C/S ZINC HEX BOLT 8
15 HWLN12 1/2-13 NYLOK INSERT LOCKNUT ZINC (1500) 8
PRODUCT NAME
MODEL NO.
Date: 7/26/2017
Rev: A
Drawn: BDYE
Sheet: 2 of 5 SPEC 2231-12A-12G
SOCCER GOAL
*OPTIONAL*
*OPTIONAL*
*OPTIONAL*

8
8
5
9
9
111 6
10
DETAIL-Y
EXPLODED
DETAIL-X
EXPLODED
PRODUCT NAME
MODEL NO.
Date: 7/26/2017
Rev: A
Drawn: BDYE
Sheet: 3 of 5 SPEC 2231-12A-12G
SOCCER GOAL
7
11
12
13
13
3
6

PRODUCT NAME
MODEL NO.
Date: 7/26/2017
Rev: A
Drawn: BDYE
Sheet: 4 of 5 SPEC 2231-12A-12G
SOCCER GOAL
4
10
14
14
6
15
15
11
2
DETAIL-Z
EXPLODED

BOM
ITEM
NO. PART NUMBER DESCRIPTION QTY.
1 PI-001-8347-S AUGER
2 VCIBB238 2 3/8" BRACE BAND
3 HWCHAIN316 24" CHAIN
4 HWCB5161 5/16"x1" CARRIAGE BOLT
5 HWFLW516 5/16" FLAT WASHER
6 HWLN516 5/16" NYLOCK NUT
4 3 1
5
6
SIDE VIEW
2
PRODUCT NAME
MODEL NO.
Date: 7/26/2017
Rev: A
Drawn: BDYE
Sheet: 5 of 5 SPEC 2231-12A-12G
SOCCER GOAL
4
4
4
4
4
4