Aqua-Marina ISLAND BT-I250 User manual

www.aquamarina.com
User’s Guide
INFLATABLE
AIR PLATFORM
EN

WATERSPORTS SAFETY CODE
Before you start
Watersports are fun and challenging but involve inherent risks of injury or death. To
increase your enjoyment of the sport and to reduce your risks, use common sense and
follow these rules:
• Familiarize yourself with all applicable federal, state, and local laws, the risks, inherent in
the sport, and the proper use of the equipment.
• Know the waterways.
• Use caution and common sense.
• Do not attempt or allow somersaults. Landing on the head or neck can cause serious
injury, paralysis or death.
• Take extreme care when swimming between the shore and the product. Be cautious of
any boat traffic or other obstructions. Ensure all users are capable swimmers and are not
excessively fatigued.
• Always ensure that the swimming area around the air platform is free of submerged logs,
rocks and sandbars. Ask about the local water conditions before use.
• Do no use without proper anchoring.
• Do not dive head first or swim under this product.
• Never use at night, or in low-light conditions.
• Never use in poor weather conditions with excessive wind, waves or lightning.
• Only allow use of the product with proper supervision. Secure the product when not in
use to prevent access by any other users.
• Do not jump or dive from this item.
• Do not jump onto this item from any other item.
• Always remove personal items such as rings, watches or other sharp objects before use.
2
For your own safety and that of your equipment,
make sure to take the following precautions.
Failure to follow warning notices and instruction
may result in property damage, serious injury or
death.
WARNING

Your equipment
• Check all equipment prior to use. Inspect your product for missing, defective or worn
parts.
• Always check for proper inflation before each use. Temperature and environmental
changes can cause changes in tube pressure. Using the product over or under inflated is
dangerous and can cause damage to the product, voiding the warranty.
• Always check security of the anchor and all attachments before each use.
• Always wear a life vest (PFD) as required by the authorities in area of use.
THE WARNINGS AND PRACTICES SET FORTH ABOVE IN THE
WATERSPORTS SAFETY CODE REPRESENT SOME COMMON RISKS
ENCOUNTERED BY USERS. THE CODE DOES NOT PURPORT TO COVER
ALL INSTANCES OF RISK OR DANGER. PLEASE USE COMMON SENSE AND
GOOD JUDGMENT.
3
ACCESSORIES
Carry Bag Double-Action Pump -
LIQUID AIR V1
STANDARD
SPECIFICATIONS
MODEL
ISLAND
BT-I250
SIZE
8’2” x 63“ x 6“
250 x 160 x 15cm
VOLUME
560 L
MAX.
RIDER WGT
584 lbs / 265 kg
MAX.
AIR PRESSURE
8 PSI
ISLAND+
BT-I250P
8’2” x 63“ x 6“
250 x 160 x 15cm 560 L 584 lbs / 265 kg 8 PSI
Connection Strap

WARNINGS AND CAUTIONS
4
8psi / 0.55bar
SWIMMERS ONLY
LES NAGEURS SEULEMENT
NUR FÜR SCHWIMMER
SÓLO LOS NADADORES
NO PROTECTION AGAINST DROWNING
AUCUNE PROTECTION CONTRE LA NOYADE
KEIN SCHUTZ GEGEN ERTRINKEN
SIN PROTECCIÓN CONTRA EL AHOGAMIENTO
265kg
584lbs
3 1
√

5
1. Unfold the Air Platform
Get yourself a clean and flat area to unfold the Aqua Marina air platform and lay it flat. In
most cases, you will need at least 9㎡to inflate the air platform.
IMPORTANT: Careful thought must be given to the setup area regarding the size
of the product. Ideally, this air platform should be carefully carried to and inflated at
somewhere close to the water.
NOTE: Dragging or sliding the air platform on the ground, either before or after inflation,
can cause damage.
2. Instruction for Assembling and Disassembling
Pump Set Up And Inflation
Inflation
1) Open the valve cap by twisting counter-clockwise. Ensure the valve is clear from
debris, sand, or dirt before releasing.
2) Push valve button in and turn counter-clockwise 90 degrees so it pops up and is in
the “OUT” position.
3) Insert the pump hose and twist it 45 degree clockwise to lock in place. Inflate until
you reach the required pressure.
Connect the pump hose to the gauge
housing and secure it tightly.
INSTRUCTION FOR ASSEMBLING AND DISASSEMBLING
A
B①①

6
DO NOT OVER INFLATE BEYOND 8PSI (0.55BAR).
THIS WILL VOID YOUR WARRANTY.
WARNING
C
D
Inflate Faster With Less Effort
•Use full range of the pump cylinder
while keeping your arms extended.
•Bend your knees and use the body
weight.
1) The pump can be switched between double action mode and single action mode.
2) After inflation, return the valve cover and tighten in clockwise direction to lock in place.
DOUBLE
ACTION
SINGLE
ACTION
Deflation
To deflate your board, follow the instructions below.
1) Open the valve cap by twisting counter-clockwise. Ensure the valve is clear
from debris, sand, or dirt before releasing.
2) Push valve button in and turn clockwise to lock it in DOWN position.

7
E
1) Completely deflate the ISLAND board by pushing out any remaining air, or use the
pump on "deflate" position for faster deflation.
2) Tri-fold the board from the longer side.
3) Fold at one fourth of the length of the tri-folded board to the middle (refer to picture 3).
4) Fold in half.
5) The carry bag is designed to allow you to get your ISLAND into the bag as easily as
possible with minimal folds.
Folding Steps
For ISLAND (BT-I250)
1) Deflate the ISLAND+ board, or use the pump on "deflate" position for faster deflation.
2) Roll up the ISLAND+ board from the shorter side to the end.
3) Push out any remaining air as you roll.
4) The carry bag is designed to allow you to get your ISLAND+ into the bag as easily as
possible.
For ISLAND+ (BT-I250P)
To properly store ISLAND+ without damaging the EVA pad,
please follow these steps:
NOTE
or
(1)
(3) (4) (5)
(2)

8
WARNING:
NEVER DRAG THE AIR PLATFORM! YOU MUST LIFT AND SET THE
PRODUCT ON THE WATER TO AVOID ANY ACCIDENTAL TEARING ON
SHARP OBJECTS.
3. Inflation Tips and Precautions
• The platform can be inflated either with our hand pump or an electric pump. Electric
Pumps can be used to inflate the platform up to 80-90% of the required air pressure.
However, the remaining pressure required should be reached by using our hand pump to
avoid over-inflation.
• Do NOT over-inflate the platform. A max pressure of 8psi is adequate.
• Do NOT use an air compressor. Damage to your air platform caused by over inflation
from an air compressor is not covered by your warranty.
• If leaving the platform inflated, we strongly recommend you to keep it under shade from
direct sunlight, and deflate the platform at least to 5PSI.
• After 2 or 3 days, there may be a slight decrease of pressure due to temperature change.
If so, add a few pumps of air.
• Do NOT pump the platform to a high pressure and leave it in the sun. If the platform is
going to be in a warm environment, slightly under-inflate it.
• Low water temperature may cause a slight loss in chamber pressure. You are
recommended to carry a pump with you to add some air when necessary.
or
(3) (4)
(1) (2)

9
OPERATION
1) This item is an inflatable air platform designed to be used on the water.
2) Two separate air platforms could be connected by using the straps (come with the
package) to connect the built-in D-rings on the board, as shown in the picture (FIG.1).
Make sure that the connection is tight and there is NO gap greater than 25mm (3/4”)
between the platforms.
IMPORTANT: Failure to properly connect the platforms may result in injury or death.
3) Do not jump or dive from the product.
4) Do not jump onto this product from another. Unexpected motion may cause a loss of
balance and injury.
5) Do not swim underneath the air platform.
6) The maximum weight capacity is 265 kg (584 lbs). It is acceptable to have up to four
(3adults + 1 child) people on the platform.
7) Do not use the air platform when connected with moving vessels.
IMPORTANT:
• DO NOT use without adequate air pressure – 6psi (0.41bar) minimum.
• DO NOT over inflate - 8psi (0.55bar) maximum.
HOW TO FIX A LEAKING VALVE
1) Inflate your platform up to the max air pressure,
8PSI.
2) Stick your valve wrench down inside of valve
and turn clockwise to tighten the valve back
down onto the platform.
1. Try to tighten the valve
(FIG.1)
open
close

10
NOTE: Correctly use the wrench by pressing it with
one hand on top.
open
close
3) Check the rubber ring to make sure that it is in the correct position, tight
around the valve and there is no debris in the way.
4) Be sure the pin spring is functioning properly and there are no cracks along
the edges.
1) Completely deflate your platform.
2) Undo the dust cap and insert the valve wrench into the valve and twist
counterclockwise to remove the valve.
5) Ensure there are no strings from the drop-stitch material.
6) Note the bottom piece of the valve is not attached to anything.
7) Fit the valve back into your platform.
8) Align all the threads and twist to tighten.
9) Once the valve is hand tight, use the valve wrench to seal completely.
Rubber Ring
2. Re-install or replace a valve
open
close

About PVC
Your new platform is made from a durable double stitch PVC. If a tear or puncture does
occur, PVC is very easy to repair. Repairs are easily done with your included patch kit.
Read the following paragraphs for leak detection and repair tips.
Air Leak Detection
If your platform is losing air pressure, not caused by colder temperatures, check the
platform for leaks, starting with the valve. A leaking valve is rare, but if you do find a leak
we can send you a replacement valve. To locate a leak, we recommend mixing soap and
water in a spray bottle, spray around the valve. If you see bubbles forming, check your
valve seating and base and be sure the valve insert is screwed tightly. If you continue to
have problems it’s probably time to order a new valve. Replacement of the whole valve can
be done with a simple tool that comes with the replacement valve.
If the platform is losing air and the valve is good, you probably have a small puncture.
Small punctures can be repaired easily and permanently. Spray around the platform until
air bubbles become visible and mark the position of the leak. If you do not find air bubbles,
inflate the air platform to maximum air pressure and try to listen to find the leak. If you can
narrow the area down, return with a spray bottle to identify the source of the leak.
Punctures less than 1/8”in size can be repaired simply without a patch. Deflate your
platform, then clean and dry the area to be repaired. Apply a small drop of glue to cover the
puncture, and let dry 12 hours.
Small Repairs
Your platform comes with a repair kit as standard equipment. If you no longer have your
repair kit, you can order a new one from your dealer. Cut a piece of repair material large
enough to overlap the damaged area by approximately 1.5cm (1/2”), and round off the
edges. Apply glue to the under side of the patch and around the area to be repaired. Too
much glue will interfere with a proper repair. Allow adhesive to become tacky for 2-4
minutes, and then starting at one corner and working outward, carefully apply the patch to
the repair area using very firm pressure. Rub the entire patch area and the edges of the
patch using very firm pressure. Allow to cure for at least 12 hours before inflating and
using.
LEAK DETECTION AND REPAIR
11

12
WARNING
1. The warranty is valid only when this product is used for normal recreational activities
and does not cover products used in rental or school operations.
2. Aqua Marina will make the final warranty determination, which may require inspection
and/or photos of the equipment, which clearly show the defect(s). If necessary, this
information must be sent to the Aqua Marina distributor in your country with prepaid
postage. Product can be returned only if a return authorization number is given in
advance by the Aqua Marina distributor. The return authorization number must be
clearly labeled on the outside of the package, or it will be refused.
3. If a product is deemed to be defective by Aqua Marina, the warranty covers the repair
or replacement of the defective product only. Aqua Marina will not be responsible for
any costs, losses, or damages incurred as a result of loss or misuse of this product.
4. This warranty does not cover damage caused by misuse, abuse, neglect, normal wear
and tear including, but not limited to, punctures, damage due to excessive heat
exposure, damage caused by improper handling and storage, damage caused by use
in waves or shore break, board breakage caused by filling or crashing in surf
conditions, or damage caused by anything other than defects in material and
workmanship.
5. This product must not be used in excess of the manufacturers recommended maximum
load capacity.
6. This warranty is void if any unauthorized repair, change or modification has been made
to any part of the equipment.
7. The warranty for any repaired or replacement equipment is available from the date of
the original purchase only.
8. The original purchase receipt must accompany all warranty claims. The name of the
retailer and date of purchase must be clear and legible.
9. There are no warranties that extend beyond the warranty specified here in.
WARRANTY
Aqua Marina warrants this product to be free from major defects in
material or workmanship to the original purchaser for a period of one (1)
year from the date of purchase. This warranty is subject to the following
limitations.
THIS PRODUCT IS DESIGNED IN ACCORDANCE WITH
STANDARDS FOR A SPECIFIC USE. ANY MODIFICATIONS
OR TRANSFORMATIONS HIGHER THAN THAT INDICATED
BY THE MANUFACTURER COULD RESULT IN SERIOUS RISKS
FOR THE USER AND WILL VOID THE WARRANTY.