Pyle DRYVER PRO PDIC60 User manual

py le
#Mf®>PRO
IN-CEILING SPEAKERS
• PDIC60 PDIC60T PDIC80 PDIC80T
• PDIC51RD PDIC61RD PDIC81RD
•PDIC55SQ PDIC65SQ PDIC85SQ
IN-WALL SPEAKERS
• PDIW52 PDIW62 PDIW55 PDIW65
INCEILING & INWALL SPEAKER
INSTALLATION MANUAL
www.pyleaudio.com

Thank you for purchasing this PYLE in-wall/in-ceiling speaker system. It is a
state-of-the-art product carefully designed and manufactured for your installation
needs, and has been thoroughly tested to ensure consistent and reliable perfor¬
mance.
If you have any question about the installation or operation of your PYLE
in-wall/in-ceiling speaker system which are not answered by this manual, contact
your dealer immediately.
INCLUDED
IN-WALL SPEAKERS
IN-CEILING SPEAKERS
SPEAKER PLACEMENT
FRONT SPEAKERS
2

REAR SPEAKERS
r—i
1
WALI
J>
IN-CEILING
Proper placement of the speakers is an important step in obtaining
the most realistic soundstage possible. These recommendations are
for the optimum placement of the loudspeakers. Use these placement
recommendations as a guide. Slight variations will not diminish your
listening pleasure. The front speakers should be placed the same di¬
stance from each other as they are from the listening position. They
should be placed at about the same height from the floor as the liste¬
ner 's ears will be, with the tweeters aimed toward the listener at ear-level height. In a home theater configu¬
ration, the two surround speakers should be placed slightly behind the listening position and ideally should
face each other and be at a level higher than the listener's ears. If that is not possible, they may be placed in
a wall (or in the ceiling) behind the listening position, facing forward. The surround speakers should not call
attention to themselves. They should provide a diffuse, ambient sound accompanying the main program mat¬
erial heard in the front speakers. In Dolby* Digital and DTS y systems, aim the tweeters toward the listening
position at ear-level height.
SPEAKER CONNECTIONS
CONNECTION TIPS
The wires for both speakers
should be the same length. If
one speaker is placed closer to
the amplifier than the other,
hide the excess wire behind
the wall.Speakers and elec¬
tronics terminals have corre¬
sponding (+) and (-) terminals.
We use red to denote the (+) termi¬
nal and black for the (-) termi¬
nal. It is important to connect
both speakers identically: {+) on
the speaker to {+) on the ampli¬
fier and (-) on the speaker to (-)
on the amplifier. Wiring “out
of phase" results in thin sound,
weak bass and a poor stereo
image. With the advent of multi¬
channel surround sound
systems, connecting all of the
speakers in your system with
the correct polarity remains
equally important in order to
preserve the proper ambience
and directionality of the
program material.
Front or Rear Speaker Outputs
3

EXISTING CONSTRUCTION
IN-WALL SPEAKERS
Cut the drywall.
Note;Always allow at least
one-half inch between a wall
stud and the speaker cutout or
the locking tabs will not be able
to swivel into place.
Screw out the two
screws to seperate
the frame first.
Place the frame assembly
in the wall.
Screw down each of the six
Phillips head screws. The
locking tabs will swivel into
place and secure the unit to
the rear surface of the drywall.
Connect the speaker wires
to the speaker.
Screw down each of the six
Phillips head screws.
Put in the strips of adhesive to
secure the grille.
The in-wall speakers feature
unique swivel mounts for the
tweeters-that enable you to aim
the very directional high frequencies
toward the listening position,
at ear-level height.
PDIW55/PDIW65
tweeter adjustment:
Before installing the speaker grille,
gently press on the outer edge of Replace the metal grille.
the tweeter mount to adjust the
position of the tweeter. The
tweeter will not swivel more than
15 degrees in any direction; do not
attempt to force it to move further.
PDIW52/PDIW62
After installing the speaker grille,
gently press on the mesh of the
tweeter to adjust the position of
the tweeter.
4

EXISTING CONSTRUCTION
IN-CEILING SPEAKERS
Cut the drywall.
Note:Always allow at least
one-half inch between a wall
stud and the speaker cutout or
the locking tabs will not be able
to swivel into place.
Strips of
adhesive
Screw down each of the four
Phillips head screws. The
locking tabs will swivel into
place and secure the unit to
the rear surface of the drywall.
Put in the strips of adhesive to
secure the grille.
Connect the speaker wires to
the speaker.
The in-celing speakers feature
unique swivel mounts for
the tweeters that enable you
to aim the very directional
high frequencies toward the
listening position, at ear-level
height. Before installing the
speaker grille, gently press on
the outer edge of the tweeter
mount to adjust the position of
the tweeter. The tweeter will
not swivel more than 15
degrees in any direction; do
not attempt to force it to move
further.
Just for PDIC60/PDIC80
After installing the speaker grille,
gently press on the mesh of the
tweeter to adjust the position of
the tweeter.
Place the frame assembly
in the wall.
Replace the metal grille.
5

WIRING DIAGRAM
(PDIC60T/PDIC80T)
70V SYSTEM
SPEAKER WIRES
PDIC80T PDIC60T
6

ATION
:>eak-
e easily
)u are
> prop-
ieakers
aler or a
TOOLS NEEDED
■ ■■ D:=)
Pencil Phillips #2 screwdriver
Measuring tape
Carpenter’s level
Utility knife
K=>
Awl
ESHOOTING
UND FROM ANY OF THE SPEAKERS:
iplifier is on and a source is playing.
nnections between receiver/amplifier and speakers. Make sure all wires are connected. Make
:er wires are frayed, cut, punctured or touching each other.
>n of your receiver/amplifier.
JND COMING FROM ONE SPEAKER:
introl on your receiver/ampiifier.
inections between receiver/amplifier and speakers. Make sure all wires are connected. Make
er wires are frayed, cut, punctured or touching each other.
I NO) BASS OUTPUTS
ions to the left and right "Speaker Inputs" have the correct polarity (+ and -).
ered subwoofer to your system.
modes, make sure your receiver/processor is correctly configured. When using a subwoofer,
er output of the receiver/ processor has been enabled. If no subwoofer is being used,
right front and rear speakers have been configured as “LARGE.'’ See your receiver/processor’s
ier information on correct speaker configuration in Dolby Digital, DTS and other surround sound
rs AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:

MODEL NO.
Cut-out Dimensions
Dimensions (each speaker)
PDIC60
7 7/8” (W) X 7 7/8” (H) X 2 3/4" (D)
9” (W) X 9" (H) X 2 3/4” (D)
PDIC60T
7 7/8”(W) X 7 7/8” (H) X 4 5/8" (D)
9" (W) X 9" (H) X 4 5/8” (D)
PDIC80
9 3 /8" (W) X 9 3 /8" (H) X 3 1 / 2" (D)
10 3/4” (W) X 10 3/4" (H) X 3 1 / 2” (D)
PDIC80T
9 3/8" (W) X 9 3 /8" (H) X 5 3 /4" (D)
10 3/4” (W) X 10 3/4” (H) X 5 3 /4” (D)
PDIC51RD
6 1 / 2” (W) X 6 1 / 2” (H) X2 5 /8" (D)
8” (W) X 8” (H) X 2 5/8” (D)
PDIC55SQ
5 3/4” (W) X 5 3/4” (H) X2 3 /4” (D)
7” (W) X 7” (H) X 2 3/4” (D)
PDIC61RD
7 7/8”(W) X 7 7/8" (H) X 2 3 /4" (D)
9" (W) X 9” (H) X 2 3/4” (D)
PDIC65SQ
7 1 / 4” (W) X 7 1 / 4” (H) X 3" (D)
8 5/8” (W) X 8 5/8” (H) X 3” (D)
PDIC81RD
9 3/8” (W) X 9 3/8” (H) X 3 1/2” (D)
10 3/4” (W) X 10 3/4” (H) X 3 1 / 2" (D)
PDIC85SQ
8 5 /8" (W) X 8 5 /8” (H) X 3 1/2” (D)
10” (W) X 10" (H) X 3 1/2” (D)
PDIW55
6 5 /8” (W) X 10 V8” (H) X 2 3/4” (D)
7 5/8” (W) X 11 1/4" (H) X 2 3 /4” (D)
PDIW52
6 5 /8" (W) X 10 VS” (H) X 2 3 /4" (D)
7 5/8" (W) X 11 VA" (H) X 2 3/4” (D)
PDIW65
7 3/4" (W) X 11 3/8" (H) X 2 7/8” (D)
8 3/4” (W) X 12 1 / 2” (H) X 2 7 18" (D)
PDIW62
7 3/4” (W) X 11 3/8" (H) X 2 7/8” (D)
8 3/4” (W) X 12 1/2" (H) X 2 7 18“ (D)
pro