Qbic EP-0400 User manual
Quick Start Guide
This guide is designed to help you quickly set up the EP-0400.
EP-0400
ePaper
Contents
EP-0400
Bracket
Tape
I/O Cover M3x4 screw *1
M3x4
Product Overview
Display
1LED
2Button 1
3Button 2
4
Button 3
5Reset
6Bracket
7Battery Cover
8
6
7
14
5
2
3
8
M3x6 screw *3
M3x6
Installa�on
1.
STEP 1
STEP 2
Fix M3 screw
STEP 1
Ah tape on the
back of bracket.
STEP 2
Fix the bracket with tape
on the surface.
STEP 3
2. Surface Mount
STEP 1
Install bracket on surface.
(
It is recommended to secure with M3 screw. The suggested length of the M3 screw is the thickness of
M3 screw Torque<2 kgf-cm
STEP 2
Mount the ePaper on
the bracket.
STEP 3
Fasten M3 screw*3 to
secure the bracket
and ePaper.
NOTICE:
1. Tape Mount
Fasten M3 screw*3 to
secure the bracket
and ePaper.
CARE AND WARNING
◎WARNING :
Changes or mcas to this unit not expressly approved by the party responsible for compliance will void
the user’s authority to operate the equipment.
◎Correct disposal of this product :
This marking indicates that this product should not be disposed with other household wastes
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device, use the return and collecn systems or contact
the retailer where the product was purchased. They can take this product for environmental safe recycling.
◎ FCC & CE RF radiaon Exposure Statement Cauon :
Place the product at least 20cm from nearby persons.
◎NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protecn against harmful interference in a residenal installaon.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicas.
owever, there is no guarantee that interference will not occur in a parcular installa.If this equipment does cause harmful
interference to radio or television recep, which can be determined by turning the equipment oand on,
the user is encouraged to try to correct the interference by one or more of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separaon between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dint from that to which the receiver is connected.
•Consult the dealer or an experienced radio/panel PC technician for help.
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condis :
•May not cause harmful interference.
•Must accept any interference received, including interference that may cause undesired opera.
◎
that can result in an explosion;
-
suivantes :
1.L’appareil ne doit pas produire de brouillage;
-
◎
◎
◎
◎
◎
ammable liquid or gas;
You can press the top and middle buttons at the same timeto get label information.
FCC ID: 2AF82-EP0400 IC: 23322-EP0400 HVIN:EP0400
About device information
CAUTION
Risk of explosion if the battery is replaced by an incorrect type.
Qbic Technology Co.,Ltd.26F.-12,No.99.Sec.1,
Xintai 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan(R.O.C)
TEL:886-2-2697-2000 FAX:886-2-2697-2868
• A degreaser or solvent-based cleaner may be required to remove heavy oil or greasefrom a surface and
•Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or
•Porous Surfaces:need to be sealed
•
migrate
•
Typical surface cleaning solvents are IPA/ water mixture or heptane.
•Bond strength is dependent upon the amount of adhesive-to- surface contact developed.
Generally, this means that the tape should experience at least 15 psi in roll down or platen pressure.
•
the bond to elevated temperatures.
Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl
◎
◎General Procedure
NOTE :greater than
for use when handling such materials.
IPA
&
Water
Step A:
Solvent wipe
Step B:
Wipe dry
Step C:
Apply tape to surface
Step D:
Roll ished joint
should be followed by cleaning with IPA/water.
surface area to improve adhesion.
copper containing metals
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
◎
Brand: Qbic
Model: EP-0400
Input: 3V 10mA
Operating Temperature: 0-40°C
Battery information:
Model : CR2450
The product contains a coin/button cell battery.
Do not ingest battery, Chemical Burn Hazard.
Keep batteries out of reach of children.
◎
Table of contents
