QFX BT-207 User manual

INSTRUCTION MANUAL
BT-207
MICRO SYSTEM
AM/FM/CD/MP3/USB/SD/AUX-IN/NFC

This“bolt Of lighting”
indicates uninsulated
material within your unit
which may cause an electrical shock.
For the safety of everyone in your
household, please do not remove
product covering
TO PREVENT
FIRE OR SHOCK HAZARD,DO
NOT EXPOSE THIS EQUIPMENTTO
RAIN OR MOISTURE.
TO PREVENT
ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT,
AND FULLY INSERT.
The“exclamation point”
calls attention to features
for which you should read
the enclosed literature closely to
prevent operating and maintenance
problems.
The normal ventilation of the
Ventilation warning:
product shall not be impeded for
intended use.
Dripping warning:
The product shall not be exposed to
dripping or splashing and that no
objects filled with liquids, such as
vases,shall be placed on the product.
EN-1
PREPARATION FOR USE
Unp acki ng and S etup
* Car eful ly rem ove th e unit from the display c arto n and re move a ll pac king m aterial from the unit i tsel f.
* Rem ove an y desc ript ive labels that m ay be fo und on e ithe r the fr ont or t op cab inet of the unit. Do not
rem ove an y labe ls loc ated on either th e back o r butt on cab inet o f the un it.
* Pre ss the C D door O PEN Bu tton to open the CD compa rtme nt doo r. There is a white ca rd in th e CD
com part ment w hich i s intended to prevent t he CD pi ckup f rom mo ving d urin g ship ment of the produ ct,
Rem ove th is car d from t he CD compartment bef ore us e.
Using AC Power
POWER SUPPLY
BASIC FUNCTION
Power Sources
Using AC Power
Connect the AC power into Standard household wall outlet. For dual voltage version.
Make sure that the AC VOLTAGE SELECTOR is switched to your local voltage.
EN-2
1.check if the power voltage, as shown on the type plate located on the bottom of the set,
corresponds to your local ac power supply. if it does not, consult your dealer or service centre .
2.connect the power cord to the ac socket inlet and the wall outlet. the power supply is
now connected and ready for use.
3.to switch off completely, unplug the power cord from the wall outlet.
unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.
Batteries (not included)
Open the battery compartment and insert eight batteries, type R-20, UM-1 or C-cells,
(preferably Alkaline) with the correct polarity as indicated by the + and - symbols
inside the compartment.
Batteries contains chemical substances, so they should be disposed of properly
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or
cause the batteries to burst. Therefore:
Do not mix battery types: e.g. alkaline with carbon Zinc. Only use batteries of the same type for
the set. When inserting new batteries, do not try to mix old batteries with new ones.
Remove the batteries if the set is not be used for a long time.
For Customer Use
Enter below the Serial No. which is located
On the bottom of the cabinet. Retain this
Information for future reference.
Mode No.
Serial No.

EN-3 EN-4
IR
1
23
4
56
7
8910
11
1213 14 15
16
17
18
25
1.
2.
3.PLAY/PA USE BUTTON
4.STOP /USB /SD BU TTON
5.REM OTE SE NSOR
6. STAN DBY IND ICATOR
7.POW ER BUT TO N
8.TIM E/PR OGRA M B UTTON
9.PRE-DN BU TTON
10. PRE-U P BUTTO N
11.REPEAT/MO /ST BUT TO N
12. FUNC TION B UTTON
13. LCD DI SPLAY
EQ BU TTON
MUT E B UTTON
14. RAND OM/B AND BU TTON
15. VOLU ME BUT TO N
16. BASS B UTTON
17.
18.
19. LEFT &RIG HT SPE AKER B OXES
20. FM ANT ENNA
21. BATTERY DOO R
22. SPEA KER WI RE CON NECTOR(R)
23. SPEA KER WI RE CON NECTOR(L)
24.A C S OCKE T
25. CD DOO R
BAC K/NE XT K NOB
AUX /PHO NES/ USB/ SD DOO R
1.EQ BUTTON
-Press the button to change EQ CD/MP3/USB/
SD/AUX/RADIO's music style.
-When playing the music, push down this button
is in the popular-jazz-FLR-classica-rock.
2.MUTE BUTTON
-Press the mute button allows CD / MP3 / USB
/SD/ AUX / the RADIO to enter the mute state.
3.PLAY/PAUSE BUTTON
- Start or pause MP3/CD/USB/SD/BT play.
-In radio mode, press the play/pause button
enter the automatic channel scan mode.
4.STOP/USB/SD BUTTON
- Stop CD/MP3/USB/SD playback;
erase a CD program.
- Press and hold more than 1.5 sec
change USB1.1/SD media(only USB).
5.REMOTE SENSOR
6.STANDBY INDICATOR
7.POWER BUTTON
-Press POWER button on.
8.TIME/PROGRAM BUTTON
-In standby mode, to setup the time of the unit.
-program and review programmed track numbers.
-In the working status, push down this button
can on CD/MP3/USB/SD/RADIO for programming.
9.PRE-DN BUTTON
- In the radio mode,
press PRE-DN button to choose the back channel.
- In the mp3 mode,
Press PRE-DN button to enter the back folder.
10.PRE-UP BUTTON
-In the radio mode,
press PRE-UP button to choose the next channel.
-In the mp3 mode,
press PRE-UP button enter into the next folder.
11.REPEAT/MO/ST BUTTON
- Repeat a track CD/MP3/USB/SD program.
- Repeat mode : normal->repeat 1->repeat all->
repeat album ->normal.
- Press MO/ST button once, to mono state.
- Press MO/ST button twice, to stereo state,
stereo is displayed (In FM mode).
12.FUNCTION BUTTON
- Select source of sound CD/USB(SD)/BT/
AUX/RADIO.
14.RANDOM/BAND BUTTON
- In a CD/MP3 / USB/SD mode,
press this button can be played at random.
- The radio in the mode, press this button
to select the FM STEREO, FM , AM.
15.VOLUME BUTTON
- Adjust volume level.
Rotate the volume button to hold the CD/MP3/
USB/SD/AUX/BT/RADIO the volume.
16.BASS BUTTON
-Press the BASS button can make the CD/MP3/
USB/SD/AUX / RADIO into the BASS state.
17.BACK/NEXT KNOB
BACK
-To setup the time standby state
BACK track selection.
- Rotate and hold more than 1.5 sec BACK
search intra track.
- In the radio mode, Rotate BACK will enter
the low end of the manual channel scan mode.
NEXT
-To setup the time standby state
NEXT track selection.
- Rotate and hold more than 1.5 sec
forward search intra track.
- In the radio mode, Rotate NEXT will enter
the high-end manual channel scan mode.
18.AUX/PHONES/USB/SD DOOR
-The built-in AUX/PHONES/USB/SD jack.
19.LEFT&RIGHT SPEAKER BOXES
20.FM ANTENNA
- To improve FM reception.
21.BATTERY DOOR
-To open battery compartment.
22.SPEAKER WIRE CONNECTOR (R)
23.SPEAKER WIRE CONNECTOR (L)
24.AC SOCKET
- Inlet for power cord.
25.CD DOOR OPEN BUTTON
- Press here to open/close the CD door.
13.LCD DISPLAY
- Show the song playing time.
- Show the FM dial frequency.
19
19
20
21
22
23 24
FIG
Top and front panels(See fig 1 )

EN-6
EN-5EN-
Remote Control USE CLOCK
to setup the time of the unit
1.connect the ac on( .
2.short according to the time button, the time will flashing on the lcd display.
3.Rotate BACK、NEXT to select the number of the time. you can setup the time format by
12h or 24h.
4.press time button to confirm.
5.then you can set the hour and the minute with the same method of steps 3-4.
6.
with the same method of steps 3-4.
Rotate
The following operation must be in standby mode)
after setup the unit time, long press the time button can setup the unit begin working time ,
Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/aux/blue mode,
the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise
it playusb or aux mode first.
Radio reception
1. FUNCTION select RADIO .
.Press BAND to select the desired wave band: FM STEREO, AM, FM, FM ST.
3.Tune to required station by
Manual Tuning: Rotate BACK or NEXT and then release within 1 sec.
Auto Tuning:
Preset Channel:(FM 30 Preset memories, )
(1) BACK/Select desired station.
(2) Press PROGRAM button once , The MEMORY number indicator begins steady
in the display.
(3) Press PRESET-UP OR PRESET- DN buttons to select the desired number.
(4) Press PROGRAM button to save that station.
(5) Repeat steps (1) to (4) procedures for other stations.
4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you
selected or Press number key on the remote control.
5.
6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.
7.Turn off the radio by press FUNCTION button select other mode or press power button
to off the unit.
Press button mode
Press the play/pause button enter the automatic channel
mode, and to be put automatically sets.
[VOL-]or [VOL +] to adjust the volume.
2
Rotate BACK/ NEXT or press PRE-DN /PRE-UP.
scan
AM 10 preset memories
Rotate NEXT
Rotate
8.Switch on again after shut down, the memory frequency still exists.
MONO/STEREO
-Press MO/ST button once, to mono state.
-Press MO/ST button twice, to stereo state, stereo is displayed.
* Please pull out the plastic paper from the battery door before use the remote control.
* When the remote control operation becomes unstable or the distance from which the
remote control works is shorter. replace the batteries with new ones.
* Using the remote control unit
To use the remote unit, point at the REMOTE SENSOR and press the buttons gently and
firmly. Remote control operation is possible within approximate 18ft (6m). However, since
the remote control range is less when the unit is used at an angle, use directly in front of
the REMOTE SENSOR, for maximum distance.
Do not expose the REMOTE SENSOR to strong light (direct sunlight or artificial lighting)
and make sure that there are no obstacles between the REMOTE SENSOR and the
remote control unit.
1. POWER BUTTON
2. OPEN/CLOSE BUTTON
3.INTRO BUTTON
4.MUTE BUTTON
5.RANDOM BUTTON
6.P-UP BUTTON
7.REPEAT/MO/ST BUTTON
8.PROGRAM BUTTON
9.BACK BUTTON
10.FUNCTION BUTTON
11.NEXT BUTTON
12.EQ BUTTON
13.PLAY/PAUSE BUTTON
14.P-DOWN BUTTON
15.BBS BUTTON
16.STOP/BAND BUTTON
17.NUMBER KEY
18.VOL- BUTTON
19.VOL+ BUTTON
4
5
1
9
10
14 15
18
19
6
2
11
8
7
13
12
17
16
3
RANDOM BUTTON
-In the player CD/MP3/USB/AUX , press the RANDOM button can be played at random.
Press again to cancel.
BBS BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the BASS button can make into the
bass state. Press again to cancel.
EQ BUTTON
-In the player CD/MP3/USB/BT/AUX/RADIO, press the EQ button to change music style.
-When playing the music, press this button is in the classica-rock-popular-jazz-FLR.
MUTE BUTTON
-In the player CD/MP3/USB/BT/AUX/ RADIO, press the MUTE button to enter the mute state.
Press again to restore volume.
INTRO BUTTON
-In the player CD/MP3/USB,press the INTRO button into 10 seconds browsing repertoire
state, press again cancel browse.

EN-8
EN-7
PROGRAM METHOD
(1)Press the [PROGRAM] key at STOP mode, system will go to PROGRAM mode.
-The PRG icon and P01 will blink at 2Hz. This prompts the user to enter the first
songs in the program PLAY list.
(2)The user can select the desire tracks by using [NEXT], [BACK] keys.
Once these keys are pressed, the Display will show the selected track.
(3)After select the desired track, press [PROGRAM] key again and it will be stored in
the memory. Mp3 Maximum 99 Maximum 20 tracks can be programmed
when Repeat steps (2) to (3) procedures.
(4)If press the [STOP] key during the program mode, then the selected TRACKs will be
stored in the memory and return to STOP mode (Continuous Play mode)
(5)If press the [PLAY] key during the program mode, it will start the program PLAY mode.
PLAY start from P01 Track
and CD
Erasing a program
You can erase the content of the memory by:
- While playing, press STOP button twice.
- Opening the CD door
- Select the other mode.
、 、 .
To listen music with a mp3 discman walkman
1.Connect to the AUX .
2.press function selector to AUX, the sound source of the mp3 or discman
or walkman will output from the unit.
-Rotate the volume control to adjust the volume.
-The unit can't control the player.
USE AUX
This CD-player can play Audio Discs,MP3 CD-R.
Do not try to play CD-ROM,CDi,VCD,DVD or
computer CD.
1.
、with the printed side
facing up and press cd door gently to close.
4.press play/pause on the set to start playback.
5.
note: cd/mp3 play will also stop when:
-you open the cd compartment;
-you select radio sound source;
-the cd/mp3 has reached to the end.
selecting a different track.
during playback you can use back or next to
select a particular track.
if you have selected a track number in the
stop or pause position, press play to start
playback.
Rotate next once briefly for the next track,
or press repeatedly until the desired track
number appears in the display.
Rotate back once briefly to return to the
beginning of a current track.
Rotate back more than once briefly for a
previous track.
finding a passage within a track
1.Rotate and hold down back or next.
the cd is played at high speed.
2.when you recognize the passage you want
release back or next.
normal playback resumes.
different play modes:repeat
repeat-play the current track continuously.
repeat all-plays the entire cd continuously.
playing tracks in random order after press
the random button, the tracks will be played
in random order.
Press function button to CD state.
2.to open the cd door, press cd open button.
3.insert a mp3/cd or cd-r
Press the pause button to pause play, press
the play button back playing.
6.to stop cd playback , press stop.
CD/MP3 PLAYER
CD/MP3 Player
Playing a CD/MP3 USB/SD Audio functions
1)press function button or stop/usb/sd button to
choose the usb or sd state.
2) PLAY/PAUSE
3) NEXT, BACK Skip search
4) Program Track(MP3 99 Track, CD 20 Track )
5) MODE : normal->repeat 1->repeat all->
repeat album ->normal
6) Maximum Folder : 99 Folders
7) Maximum File : 999 Files
-Press and hold the [STOP] key more than 1.5sec
at USB mode , system will change to SD mode.
Then “SD“ will be display. At this moment,
system will read the SD .
- If a device is successfully read, then the
correspond device is ready to play a file.
- If a device fails to be read, then “NO” will
be appeared on the Display to indicate that there
is no device .
*Notice : If no device is attached or the player
fails to read the device when a user switch over
USB to SD with pressing [STOP] key,
then “NO” is displayed and the system moves
into the STOP mode.
-When the unit has not the disc, inserting the
usb/sd card will automatically real usb/sd card,
it read the USB first while having the USB.
REPEAT
-The unit don’t support the HDD all and the portion
usb with mp3 player.
Note: at the mode of CD/MP3 / USB/SD,the lcd will
display the number of song or the song playing time.
Playing a USB/SDPlaying a USB/SD

EN-9 EN-10
Press FUNCTION button select to bluetooth mode. Search bluetooth equipment ”BT-207" math
connection, such as need to enter pass word for “0000".
1. Press PLAY/PAUSE button to play or pause playback.
2. Rotate [VOL-]or [VOL +] to adjust the volume size.
3. Rotate BACK or NEXT to select tracks.
NOTE: Bluetooth effective receiving distance of about 10M,different bluetooth devices may be
slightly different operation, please read carefully before operation you use the bluetooth device
(IPHONE, IPAD,MOBILE PHONE, ETC.) Instructions.
NFC(Near Field Communication) function for Phone or Tablet
First, press FUNCTION button to select bluetooth mode.
If your phone(tablet) support NFC, first turn on bluetooth NFC working mode, and confirm setting
“Allow data exchange when it torches another device”.
Move your phone(tablet) to near this unit(USB-92) no more than 10CM, or lightly touch the NFC
sensor area.
When hear a sound “Di Da” from the USB-92 that means connect success. Then you can play the
music through the USB-92 from your phone(tablet).
USE NFC
NFC
OPEN/CLOSE

TECHNICAL SPECIFICATIONS
GENERAL
Power Requirement ............................................................AC 120/220V~50/60Hz
Power consumption .............................................................AC 20 Watts
Dimensions......................................................Appro.434 mm(L)x214 mm(W) x228 mm(H)
Operation temperature.........................................................+5°C - +35°C
RECEIVER SECTION
Receiving Bands...................................................................AM/FM
Tuning Range..........................................................AM: 530-1710kHz
FM: 88-108MHz
AUDIO SECTION
Power output .........................................................................Maximum 3 Watt x2
Headphone Impedance ............................................................4 ~ 32 Ohms
ACCESSORIES
Instruction Booklet.....................................................................1
Remote control..........................................................................1
Ac line cord...............................................................................1
EN-11
Insert a CD,MP3, CD-R.
No CD/MP3 inserted
CD/MP3/USB/SD playback does not work
CD/MP3/USB/SD badly scratched/dirty
Replace/clean CD/MP3/USB/SD
(see maintenance)
The CD/MP3 skips tracks
CD/MP3 damaged or dirty
Replace or clean CD/MP3
- CD-R、is blank or the disc is
not finalized
Use a finalized CD-R.
EN-12