Qian QOP-T10UB-DI User manual

MODEL QOP-T10UB-DI
THERMAL LABEL PRINTER
IMPRESORA TÉRMICA DE ETIQUETAS
Please read carefully before using your equipment
and save it for future reference.
Por favor lea cuidadosamente antes de usar su equipo
y guárdelo para uso de futuras consultas.
USER MANUAL / MANUAL DE USUARIO

2
WARRANTY AND PRODUCT
INFORMATION
These terms shall be governed and construed under laws of the
jurisdiction in which the product was purchased, if any term here is
held to be invalid or unenforceable, such term (in so far as it is invalid
or unenforceable) shall be given no effect and deemed to be excluded
without invalidating any of the remaining terms. Qian reserves the right to
amend any term at any time without notice.

3
Print Label Zlabel
Android editing software IOS editing software
Install Password:1234
Version: April 2023
Please install the driver from the CD-ROM.

4
SAFETY TIPS
This section presents important information intended to ensure
safety and effective use of the printer. Please read carefully.
Notes on safety
Be sure to use the specied power source provided by our
company.
Connection to an improper power source may cause re,
explosion or damage to the printer.
Please don’t open the paper warehouse cover when it is
printing or when printing has just nished, do not touch the
print head with hand or body, overheat may cause scald.
Notes:
1. Do not store the printer in hot and humid area.
2. The printer’s adapter needs a stable power 110~220 Volts.
Please do not use other devices on the same power socket, to
avoid voltage uctuations.
3. Avoid water or conductive material (for example: metal). If water
is present on the surface please turn off the power immediately.
4. Please ensure that a paper roller is always inserted in the
printer to avoid damaging the printing roller and the printer head.
5. Please ensure that your printer is serviced and repaired by a
qualied technician. No responsibility is taken for misuse and/or
non-qualied servicing.
6.In order to ensure print quality and longevity of your printer,
please ensure that only good quality paper rolls are used.
7.Please keep this manual in a safe place, where it can be
accessed easily and used for your reference.

5
APPEARANCE
Feed button
Status light
Power light
Paper exit
180 mm
226 mm
147 mm
Button
Size: 226*180*147mm
Weight: 1200g

6
THE INSTALLATION OF THE PAPER ROLL
The printer uses a thermal label paper and adapt for easy paper
loading. So, the paper is very convenient to install. It also supports
various paper specications for printing.
Thermal paper installation method is as follows:
(1) Open the printer’s top cover.
(2) Adjust the guide space according to paper size.
(3) Insert the thermal paper into the paper guide.
(4) Pull out a little portion of the paper from the printer and close
the top cover.
Thermal label paper
installation method

7
Thermal receipt paper
installation method
Finger pinching
prevention design
Press the cover bracket to
the card slot to close the cover
Lift the bracket button to adjust the position
Press the bracket button to lock the position

8
INSTRUCTION OF LED AND BUTTONS
Power(blue light) Printer status
Off Printer off
On Printer is on and have
paper
Flash Printer is on and no paper
When printer power on, press
the FEED button
Paper out /Label positioning
detection
Hold down the FEED button in
the shutdown state, and then
power on the printer, when you
see the BLUE light is ON-OFF
then release the button
Print self-test page
Hold down the FEED button in
the shutdown state, and then
power on the printer, when you
see the BLUE light is ON-OFF-
ON, then release the button
HEX mode (press FEED
button two times to exit
HEX mode)
Hold down the FEED button in
the shutdown state, and then
power on the printer, when you
see the BLUE light is ON-OFF-
ON, then release the button. (If
the printer is setting to another
printing mode or something
else, resulting in the printer not
working properly, it is neces-
sary to reset the correct prin-
ting mode of the printer.)
Change the print command
between TSPL, CPCL and
ESC/POS

9
PRINTER DRIVER INSTALLATION
Note:
A printing software is required to be used with this driver.
Please install the driver from the CD-ROM.
1. Please choose “Yes” to allow the installation.
2. Please read the related terms carefully, and install it as
agreement as below, then click “Next”.

10
3. If the printer is USB interface, click the “USB Port” to
automatically identify the USB port, click “Install Driver”.