Qlight SAMP12 User manual

ww w.qlight.com
SAMP
Thank you for purchasing QLight product. Please read this manual
carefully before installing this product for safe and long use.
▪One touch function allows convenient connection between
signaling sound and warning light.
▪50W high power with clear and stable signal sound
▪Built-in switch for emergency message on microphone
▪This product can be combined with Emergency light bar (ELV,
ELM).
▪Aluminum and steel housing feature provides excellent durability
to vibration.
▪Materials : Housing-STEEL, Bottom plate-AL
▪Output(Max) : 50W
Model
Voltage
Built-in sounds
Frequency
WGT
SAMP12/
SAMP24
DC12V/
DC24V
Emergency
450~900Hz
1kg
Police
550~1650Hz
Fire
550~1350Hz
Buzzer
0~1300Hz
Horn
0~1000Hz
(Front Panel)
Y / L F / L W / L H / L
YELP WAIL HI-LO HORN AUX
BUZZ
POWER
VOL.
MIC
Min Max
ON
OFF
(1) (7) (2) (8) (3) (10) (4) (11) (5)
(9)
(6) (12) (13) (14) (15) (16) (17) (18)
(Rear Panel)
1. Front panel
(1) Power supply LED.
(2) Emergency LED.
(3) Flashing light LED
(4) Warning light LED
(5) Emergency/warning sound LED
(6) Power switch
(7) Emergency button
(8) Flashing light button
(9) Volume control lever
(10) Warning light button
(11) Emergency sound/warning light button
(12) Policy sound button
(13) Fire sound button
(14) Emergency sound button
(15) Buzzer sound button
(16) Horn sound button
(17) AUX button
(18) Microphone input terminal
2. Rear panel
(19) AMP power supply fuse (Upside Amber fuse 20A(AMP), downside
Red fuse10A(LIGHT)).
(20) AMP and Light power supply input terminal
OPERATING MANUAL
EMERGENCY SCATTERING AMP
AMBER FUSE 20A(AMP)
RED FUSE 10A
( Warning light )
1
Product Features
2
Specification
3
Technical Diagram
4
Structure Drawing

ww w.qlight.com
Lead wire for power supply and product control is connected to
the Connector that is thrown out from power supply wire hole.
Please read carefully this instruction to wire.
▪Wiring instructions
1) Interconnect the connecters between Light bar and amplifier.
2) Wire external power supply cable into power source from the
vehicle.
▪Wire red line ①into positive pole(+).
▪Wire black line ②into negative pole(-).
※Caution
When you wiring, make sure the polarity and it may cause
malfunction of the product.
3) Flashing light (AMBER)⑤is DC power. And if needed, wire and
use it.
Connection wire is not provided.
▪Mounting bracket for vehicle is provided with product.
Please use mounting bracket so that the product is not isolated
from the vehicle.
▪If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem on
product operating. Make sure the using voltage does not exceed
+/-5% of the rated voltage.
▪If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored or
deformed. Please be careful.
Symptom
Reason
Solution
Amplifier not working
Fuse disconnection
Replace fuse
No power supply
Make sure power supply
Amplifier trouble
Ask to distributor
Sound output failure
Wrong wiring
Recheck wiring
Horn trouble
Ask to distributor
Amplifier trouble
5
Wiring Instructions
6
Mounting Instructions
7
Caution
8
Trouble Shooting
QLIGHT CO., LTD.
http://www.qlight.com
E-mail : [e-mail]
Overseas Sales Team / Factory
Tel) [phone] Fax) [phone]
185-25 Mukbang-ro Sangdong-Myeon, Gimhae-Si,
Gyeongsangnam-do, Korea
Inquiry for Product and C/S