Qlight S125S User manual

1
Xenon Strobe Light
S125S/ S125SM
S125S - 220 - R
[Model
number] [Voltage] [Color]
| | |
• S125S
• S125SM
• 12/24
- DC12V-24V
• 110 -AC110V
• 220 -AC220V
R-Red
A-Amber
G-Green
B-Blue
• Protection rating : IP54
• Ambient operating temperature : -30°C to +50°C
Model
number
Voltage Current
Bulb specications
Certicate Weight Color
Volts/
Watts
Conguration Part#
S125S
DC12V
-24V
Max.
1.000A
200V
-550V
EUB0641
-1A(G)
U type
48
0.37kg
R-Red
A-Amber
G-Green
B-Blue
AC110V 0.135A
0.32kg
AC220V 0.105A
S125SM
DC12V
-24V
Max.
1.000A
200V
-350V
0.40kg
※CE compliant :
DC12V-24V
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
Ordering Specications Product Specications
Please scan the QR code for more
detailed product information.
www.qlight.com
5030
54

2
• First, remove the ange nuts from bolts and place the
product through the mounting surface holes.
• Fasten the ange nuts on the opposite side of the
mounting surface until the product is tightened securely.
• S125SM models have strong magnets at the base of the
product that allows attachment to any metal surface.
■
Parts Denition
■
Installation
• External power line - UL1015 AWG18(0.75sq) x 2C 400mm(S125S)
• External power line -IEC42(0.75sq) x 2P 2mm(S125SM)
• This product can be wired regardless of polarity.
• S125SM models, please connect the cigarette lighter plug of the product to a cigarette lighter socket of a vehicle.
S125SM
S125S
125
10314
13
Ø123
Ø10 CABLE ENTRY Ø10 CABLE ENTRY
PCD 85
360˚/3-M5 BOLT
123
103
14
PCD 85
360˚/3-Ø22 MAGNET
Ø123
(0.75sq)×2P 2m
Red
Black
White
Black
Power Power
Fuse Fuse
DC AC
S125S S125SM
Parts Denition/ Installation
Dimensions
(Units : mm)
Wiring Instructions
Magnetic mounting base Cigarette
lighter plug
Lens(AS)
Housing (ABS)
Rubber spacer
Flat washer
Flange nut
Xenon bulb

3
• Machine holes on the mounting surface refer-
ring to the diagram below. (S125S only)
■
Mounting Hole Specications
PCD 85
3-Ø6 HOLES
S125S
Mounting Hole Specications/ Xenon Bulb Replacement lnstructions
Mounting Accessories (Sold Separately)
Dimensions
S125S
SWP125 SWM125
• Please refer to the dimensions below for installation of mounting brackets
Ø22 Ø22
Ø10 CABLE ENTRY
6-Ø5.5 HOLES
360°/ 3-
Ø5.5 HOLES
6-Ø5.5 HOLES
4-Ø5.5 HOLES
Ø10 CABLE ENTRY
4-Ø5.5 HOLES
360°/ 3-
Ø5.5 HOLES
70
94
69
11.5 26.5
117
PCD50
PCD85
PCD60~70
70
90
65
115
11.5 26.5
PCD50
PCD85
PCD60~70
■
Xenon Bulb Replacement instructions
• Please wait at least 30 mimutes after turning o󰀨 the power
before replacing the xenon bulb.
• Please pull out the entire xenon bulb structure
①
to disas-
semble.
• For xenon bulb assembly, please ensure the connector portion
of the xenon bulb structure matches the pin location
②.
①
②
Disassemble
bulb Assemble bulb
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP54.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated(IP54), it may cause malfunction or damage to the product.
• In case of outdoor applications, install the product in the upright position. Do not install the product horizontal or upside-
down positions where water can potentially penetrate into the product and impact it’s operation.
• For further information, please visit our website (www.qlight.com).

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. [phone] Fax. [phone]
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - S125S - 2106A