QualGear QG-SB-002-BLK User manual

Installing the Speaker onto the Mount
4
7
QG-SB-002-BLK
UNIVERSAL SPEAKER WALL MOUNT
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
3.5kg
(7.7lbs)
3.5kg
(7.7lbs)
Version August 2020
Speaker
Assemble the speaker bracket and speaker assembly with the
speaker mount by using the knob and flat nut that was previously
removed from step 1.
Then insert the assembled
speaker mount with speaker
onto the wall plate. Secure it
by tightening the screw.
Speaker can be adjusted by
swiveling±70° left or right, and
by tilting ±20°up or down.
Speaker Bracket
Speaker Mount
Wall Plate
Scan the QR Code™ below
for more info about this product:
Version August 2020

Please read the entire installation manual before you start installation and assembly.
1
NOTE
WARNING
This product was designed to be installed on the following wall construction only:
WALL CONSTRUCTION HARDWARE REQUIRED
WoodenStud Included
Wooden Beam Included
Solid Concrete Included
Other Contact Qualified Professional
Do not begin to install your QualGear product
until you have read and understood all the
instructions and warnings contained in this
installation manual. If you have any questions
regarding the instructions, for US customers
please contact QualGear customer support
via email at [e-mail]. For
all international customers, please contact
your local distributor.
This product should only be installed by
someone of good mechanical aptitude, has
experience with basic building construction,
and fully understands these instructions.
This product was designed to be installed
and utilized only as specified in this manual.
Improper installation of this product may cause
damage or serious injury. QualGear is not
liable for the improper use or installation of its
products.
Make sure that the supporting surface
will safely support the combined load of the
equipment and all attached hardware and
components.
Always use an assistant or mechanical
lifting equipment to safely lift and position the
equipment.
Tighten screws firmly, but do not over tighten.
Over tightening can damage the items, greatly
reducing their holding power.
ALL QUALGEAR products are intended for
indoor use only and any outdoor use voids the
limited warranty.
ALL QUALGEAR products are designed
and tested for residential use only and any
commercial use voids the limited warranty.
For warranty information, please visit
http://www.qualgear.com/warranty.php.
If mounting to wooden studs, make sure that
mounting screws are anchored into the center
of the studs. Use of an edge-to-edge stud finder
is highly recommended.
Never exceed the maximum rated weight
specified in this manual.
All bolts and screws must be used at the
designated points in the installation instructions
to prevent property damage and/or personal
injury.
DO NOT install near air conditioner vents or
where there is excessive dust or smoke.
When drilling holes in the wall, it is very
important to take care of electrical cables,
water, or gas pipes in the wall.
2
IMPORTANT! Please read the entire installation manual and check that all parts are
included before you start installation and assembly.
Part and Hardware Package
ST4.2x24mm
Lag Bolt (x4)
6x29mm Concrete
Anchor (x4) M5x12 Screw (x4)
Disassembling the Speaker Wall Mount
1
Loosen and remove the screw in order
to separate the wall plate from the
speaker wall mount.
Loosen and remove the knob and the
flat nut in order to separate the speaker
bracket from the speaker mount.
QG-SB-002-BLK
Marking Template (x1)
W-A W-B W-C
Wall Plate
Flat Nut
Knob

Installing the Speaker Bracket
2
Screw the speaker bracket onto the speaker.
3a
Using an edge-to-edge stud finder, find the
edges of the stud.
1
Using a level, mark the centerline of the stud.
2
Stud Finder
Mounting to a Wooden Stud Wall
34
NOTE For concrete mounting,
see Step 3b.
Using a Phillips screwdriver, mount the wall plate and fasten with the provided screws (W-A).
Wall Plate
ø 2.4mm
(ø 3/32")
3
5
Using the marking template, mark two holes for
drilling on the centerline of the stud.
QG- SB- 002 -BLK
SKIP TO STEP 4
NOTE Do NOT use power drill and do NOT over tighten the lag bolts.
Using a power drill and 3/32" drill bit, drill pilot
holes of 3/32" (2.4mm) diameter and at least
1" (25 mm) depth.
4
25mm25mm
(1")
(1")
Speaker Bracket
Speaker
W-A
W-C

56
Wall Plate
Mounting to a Concrete Wall
3b
Use the marking template, place it against the wall where you want to install the speaker.
Level the marking template and mark two holes for drilling.
2
Marking Template
QG-SB -002-BLK
1
Using a power drill and 7/32" masonry drill bit, drill pilot holes of 7/32" (5.5mm) diameter and at
least 1.2" (30 mm) depth.
Place concrete anchors (W-B) in each hole. Tap each anchor flush with the wall using a hammer.
Mount the wall plate and fasten screws (W-A) using a Phillips screwdriver.
ø 5.5mm
(ø 7/32")
3
4
30mm30mm
(1.2")
(1.2")
W-A
W-B