QubicaAMF BES X User manual

REV. 9JUNE 2018
P/N: 400288005
INSTALLATION MANUAL

BES X Installation Manual, Rev.9, Jun 2018
2
P/N: 400288005
WORLDWIDE HEADQUARTERS
8100 AMF Drive
Mechanicsville, VA 23111 - USA
Phone: [phone]
Fax: [phone]
EUROPEAN HEADQUARTERS
Via della Croce Coperta, 15
40128 Bologna - Italy
Phone: [phone]
Fax: [phone]

BES X Installation Manual, Rev.9, Jun 2018 Table of Contents
P/N: 400288005 1
Table of Contents
TABLE OF CONTENTS...............................................................................................................1
SUMMARY OF CHANGES.........................................................................................................6
GENERAL INSTALLATION NOTES..............................................................................................7
RJ45 CONNECTORS. ................................................................................................................8
1 -SYSTEM COMPONENTS .................................................................................................9
1.1 - 4HD-HUB and 5HD-HUB......................................................................................................... 10
1.1.1 - Installation notes ................................................................................................................... 10
1.1.2 - 5HD-HUB label description.................................................................................................... 11
1.1.3 - 4HD-HUB label description.................................................................................................... 11
1.1.4 - Connections ........................................................................................................................... 11
1.1.5 - How the 4HD/5HD-HUB works .............................................................................................. 12
T.20.107 –288250025 5HD-HUB .......................................................................................................... 13
T.20.102 –288250021 4HD-HUB Rev.3................................................................................................. 14
T.20.076 –288250018 4HD-HUB .......................................................................................................... 15
1.2 - 4HD-CPU and 5HD-CPU.......................................................................................................... 16
1.2.1 - Installation notes ................................................................................................................... 16
1.2.2 - 5HD-CPU Label description.................................................................................................... 17
1.2.3 - 4HD-CPU Label description.................................................................................................... 17
1.2.4 - Connections ........................................................................................................................... 18
1.2.5 - How the 4HD/5HD-CPU works............................................................................................... 18
T.20.106 –288250023 5HD-CPU............................................................................................................ 19
T.20.084 –288250020 or 288250017 4HD-CPU ................................................................................... 20
T.00.071 –Mounting the 4HD/5HD-CPU on a single monitor frame.................................................... 21
T.00.072 –Mounting the 4HD/5HD-CPU on a double monitor frame.................................................. 22
T.90.174 –4HD/5HD-CPU mounting...................................................................................................... 23
2 -ELECTRICAL SPECIFICATIONS .......................................................................................25
3 -BES X SYSTEM CONFIGURATIONS ................................................................................27
3.1 - No console present................................................................................................................ 28
T.10.025 –2 overhead monitors no console......................................................................................... 29
3.2 - EasyKey console brief description ......................................................................................... 30
3.3 - EasyKey Pair console.............................................................................................................. 30
T.10.026 –2 overhead monitors with EasyKey Pair console ................................................................ 31
3.4 - EasyKey Lane and EasyKey Twin console............................................................................... 32
T.10.027 –2 overhead monitors with EasyKey Lane console............................................................... 33
T.10.028 –2 overhead monitors with EasyKey Twin console............................................................... 34
3.5 - SuperTouch console brief description................................................................................... 35

Table of Contents BES X Installation Manual, Rev.9, Jun 2018
2
2 P/N: 400288005
3.6 - SuperTouch Pair console ....................................................................................................... 35
T.10.058 –2 overhead monitors with SuperTouch Ver.2 Pair console................................................. 36
T.10.029 –2 overhead monitors with SuperTouch Pair console .......................................................... 37
3.7 - SuperTouch Lane console...................................................................................................... 38
T.10.059 –2 overhead monitors with SuperTouch Ver.2 Lane console ............................................... 39
T.10.030 –2 overhead monitors with SuperTouch Lane console......................................................... 40
4 -CONSOLE PEDESTAL ASSEMBLY...................................................................................41
T.10.060 - 286002861 single and 286002863 short single pedestal assembly parts............................ 42
T.10.061 - 286002861 single and 286002863 short single pedestal assembly instructions................. 43
T.10.065 - 286002864 single pedestal assembly with table parts........................................................ 44
T.10.066 - 286002864 single pedestal assembly with table instructions ............................................. 45
T.10.040 –286002800 single and 286002827 short single pedestal assembly parts........................... 46
T.10.041 –286002800 single and 286002827 short single pedestal assembly instructions................ 47
T.10.055 –How to mount an EasyKey console on the pedestal –single.............................................. 48
T.10.056 –How to mount a SuperTouch console on the pedestal –single.......................................... 49
T.10.062 - 286002862 dual pedestal assembly parts............................................................................ 50
T.10.063 - 286002862 dual pedestal assembly instructions................................................................. 51
T.10.067 - 286002865 dual pedestal assembly with table parts .......................................................... 52
T.10.068 - 286002865 dual pedestal assembly with table instructions................................................ 53
T.10.042 –286002801 dual pedestal assembly parts........................................................................... 54
T.10.043 –286002801 dual pedestal assembly instructions ................................................................ 55
T.10.057 –How to mount the EasyKey consoles on the pedestal –twin............................................. 56
T.10.069 - 286002830 and 286002868 parts and instructions ............................................................. 57
T.10.064 - 286002869 BES X consoles table mount assembly.............................................................. 58
T.10.048 –286002840 BES X console table mount assembly............................................................... 59
T.10.051 –610325104 Kit for mounting two BES X pedestals at 96° (286002845).............................. 60
T.10.053 –610325104 Kit for mounting two BES X pedestals at 60° (286002846).............................. 61
T.10.054 –610325104 Kit for mounting one BES X pedestal (286002847) .......................................... 62
5 -SCORING NETWORK....................................................................................................63
5.1 - Installation notes ................................................................................................................... 64
T.20.096 –BES X scoring network cables length................................................................................... 65
T.20.104 –4HD/5HD-HUB installed on XLi pinspotters with low ceiling safety kit............................... 66
T.20.083 –4HD/5HD-HUB installed on XLi pinspotters with safety kit................................................. 67
5.2 - Centers with up to 12 lanes................................................................................................... 68
5.2.1 - Centers with up to 12 lanes with single channel video server.............................................. 68
T.20.091 –BES X scoring network with: up to 12 lanes and single channel video server .................... 69
5.2.2 - Centers with: up to 12 lanes, MMS or TCS or Q-COM and single channel video server....... 70
T.20.092 –BES X scoring network with: up to 12 lanes, MMS or TCS or Q-COM and single channel
video server........................................................................................................................................... 71
5.2.3 - Centers with: up to 12 lanes, MMS, TCS, Q-COM and single channel video server.............. 72

BES X Installation Manual, Rev.9, Jun 2018 Table of Contents
P/N: 400288005 3
T.20.093 –BES X scoring network with: up to 12 lanes, MMS, TCS, Q-COM and single channel video
server ............................................................................................................................................... 73
5.3 - Centers with more than 12 lanes and up to 68 lanes or split-house..................................... 74
T.20.094 –BES X scoring network for centers with more than 12 lanes and up to 68 lanes ............... 75
5.4 - Centers with more than 68 lanes or split-house ................................................................... 76
T.20.095 –BES X scoring network for centers with more than 68 lanes .............................................. 77
5.4.1 - Scoring Network IP addresses ............................................................................................... 78
T.20.081 –BES X connection to front desk ........................................................................................... 79
T.40.012 –Cat.5e Wall Mounting Box standard network cable ........................................................... 80
T.40.008 –Standard Network Cables.................................................................................................... 81
6 -LCOM LINE..................................................................................................................83
6.1 - LCOM wiring........................................................................................................................... 85
6.2 - Replacement of LCOM devices.............................................................................................. 85
6.3 - Solving problems on the LCOM line....................................................................................... 85
7 -OVERHEAD MONITORS ...............................................................................................89
7.1 - Preface................................................................................................................................... 90
7.2 - Monitor requirements........................................................................................................... 90
7.3 - How to enable the “Just Scan” (or “Screen Fit”) and “HDMI-CEC” capabilities on monitors
supplied by QubicaAMF ........................................................................................................................ 91
T.00.064 –Monitor position.................................................................................................................. 93
T.00.065 –4HD/5HD-CPU monitor connection .................................................................................... 94
T.00.069 –610325206 infrared transmitter.......................................................................................... 95
8 -TV SIGNAL WIRING......................................................................................................97
T.00.011 –Cable television installation, TV displays............................................................................. 98
T.00.012 –Cable television installation, detail of four lanes ................................................................ 99
9 -FRONT DESK.............................................................................................................. 101
9.1 - Installation Notes................................................................................................................. 102
9.2 - ConquerorPRO Residential Edition installation................................................................... 103
9.3 - Lanes Control Box Service.................................................................................................... 104
10 -SINGLE CHANNEL VIDEO SERVER ............................................................................... 105
10.1 - 288201089 wiring ................................................................................................................ 106
10.1.1 - How to change the video standard from NTSC to PAL with 288201089............................. 106
10.2 - 288201034 wiring ................................................................................................................ 108
T.90.247 –288201089 single channel video server............................................................................ 109
T.90.211 –288201034 single channel video server............................................................................ 110
T.90.235 –Single channel video server connection............................................................................ 111
11 -COMPATIBILITY WITH MICRO AND FLY CONSOLES DIAGRAMS................................... 113
T.10.031 –2 overhead monitors IR Fly console .................................................................................. 114
T.10.032 –2 overhead monitors IR Micro I console ........................................................................... 115

Table of Contents BES X Installation Manual, Rev.9, Jun 2018
4
4 P/N: 400288005
T.10.033 –2 overhead monitors IR Micro II console .......................................................................... 116
T.10.034 –2 overhead monitors Fly console ...................................................................................... 117
T.10.035 –2 overhead monitors Micro I console ............................................................................... 118
T.10.036 –2 overhead monitors Micro II console .............................................................................. 119
12 -SYSTEM FIRST START-UP ........................................................................................... 121
12.1 - System first start-up procedure........................................................................................... 122
12.2 - Lane setup parameters screen brief description................................................................. 127
13 -SYSTEM BOOT UP SEQUENCE .................................................................................... 133
13.1 - Boot-up screen description.................................................................................................. 134
13.2 - Error list ............................................................................................................................... 136
14 -HOW TO.................................................................................................................... 139
14.1 - How to turn on/off the pair of lanes ................................................................................... 140
14.1.1 - Turning ON the system. ....................................................................................................... 140
14.1.2 - Turning OFF the system....................................................................................................... 140
14.2 - How to boot the BES X system in emergency (in the case of a ConquerorPRO server PC
crash) ............................................................................................................................................. 140
14.2.1 - How to open a lane from an EasyKey bowler terminal. ...................................................... 141
14.2.2 - How to open a lane from a SuperTouch bowler terminal................................................... 141
14.3 - How to upload programs or reinitialize the system ............................................................ 141
14.4 - How to upload animations to the 4HD/5HD-CPU units....................................................... 142
14.4.1 - Upload Animations buttons brief description ..................................................................... 144
14.5 - How to configure the speaker and microphone for the Virtual Waiter in Windows .......... 145
15 -BES X DUAL MODE .................................................................................................... 147
15.1 - Introduction......................................................................................................................... 148
15.2 - Installation Layout ............................................................................................................... 148
T.90.262 –Typical layout with 5HD-HUB ............................................................................................ 149
T.90.263 –5HD-HUB connection with Highway66.............................................................................. 150
T.90.250 –Typical layout with 4HD-HUB and 4HD-2COM units for Highway66................................. 151
T.90.251 –4HD-HUB and 4HD-2COM units connections.................................................................... 152
15.3 - Software setup..................................................................................................................... 153
15.3.1 - Dual Mode ConquerorPRO Lane Setup ............................................................................... 153
16 -REPLACEMENTS ........................................................................................................ 155
16.1 - How to replace the 4HD/5HD-HUB unit .............................................................................. 156
16.2 - How to replace the 4HD/5HD-CPU unit............................................................................... 156
16.3 - How to replace an EasyKey console .................................................................................... 158
16.4 - How to replace a SuperTouch console ................................................................................ 158
17 -PARTS....................................................................................................................... 161
T.90.237 –BES X Parts......................................................................................................................... 162

BES X Installation Manual, Rev.9, Jun 2018 Table of Contents
P/N: 400288005 5

Summary of changes BES X Installation Manual, Rev.9, Jun 2018
6
6 P/N: 400288005
Summary of changes
REV 9 (JUN 2018)
Added the 5HD-HUB.
Revised 610325104 kit tables.
Updated the console pedestal assembly tables.
REV 8 (April 2016)
Added the 5HD-CPU.
REV 7 (February 2016)
Added the paragraph “How to boot the BES X system in emergency (in the case of a ConquerorPRO
server PC crash)”.
Added the BES X Dual Mode installation and configuration paragraph.
Updated the “How to upload animations to the 4HD/5HD-CPU units” procedure.
REV 6 (June 2015)
Added new video server.
Added “boot up sequence” section and updated the error list.
Added the “How to” section.
Revised section 3 “BES X system configurations”.
Revised table “T.40.012 Cat.5e wall mounting box standard network cable”
Added “LCOM wiring” to the section “LCOM line”
REV. 5 (February 2015):
Added SuperTouch Rev.2.
Added drawings for pedestals: 286002830, 286002861, 286002862, 286002863, 286002864,
286002865, 286002869.
Added EMEA LG monitors.
Updated System first startup procedure.

BES X Installation Manual, Rev.9, Jun 2018 General Installation Notes
P/N: 400288005 7
General Installation Notes
For devices directly connected to the power, it is necessary to check that the electrical capacity of the
system is suitable for the maximum power requirements of the equipment (as indicated on the labels of
the equipment).
Always open the circuit breaker and disconnect the power plug from the powered units before looking for,
and clearing, any problem.
To reduce the risk of fire or electrical shock, do not expose this equipment to moisture.
This appliance must be positioned such that the mains supply cord connector is accessible after installation.
Be aware of the voltage being supplied to the equipment (i.e. from 100V to 240V) and that the equipment
is set for the correct voltage (when applicable).
Failure to set the equipment for the correct voltage will result in damage to the equipment.
The electrical safety of the equipment is obtained only when the equipment is connected to an effective
GROUNDING SYSTEM (in accordance with the existing electrical codes and safety regulations).
It is necessary to have the power and grounding inspected by a licensed and certified electrician.
The manufacturer cannot be responsible for possible injury, damages or malfunctioning of the equipment
due to the absence of or improper grounding of the equipment.

RJ45 connectors. BES X Installation Manual, Rev.9, Jun 2018
8
8 P/N: 400288005
RJ45 connectors.
Each connector internally have sharp prongs that when crimped pierce the insulation of the wire and
connect with the conductor. Ethernet cables may have solid or stranded wire conductors and the sharp
prongs are different in the connectors made for each type of wire. Connectors for solid (single strand) wire
often has three, slightly splayed, prongs on each contact to securely surround and grip the conductor.
Connectors for stranded wires have prongs that are designed to connect to multiple wire strands.
Connector plugs are designed for either solid or stranded wire; a plug for one wire type might not make
reliable contact when crimped to a cable with wires of the other type.
RJ45 CONNECTOR FOR
SOLID NETWORK CABLE
RJ45 CONNECTOR FOR
PATCH NETWORK CABLE

SECTION 1
SYSTEM COMPONENTS
INSTALLATION MANUAL

System components BES X Installation Manual, Rev.9, Jun 2018
10
10 P/N: 400288005
The core of the BES X scoring system is composed by two units: the 4HD/5HD-HUB and the 4HD/5HD-CPU
units. Install this couple of units for each pair of lanes present in the bowling center, as explained in this
manual.
1.1 - 4HD-HUB and 5HD-HUB
IMPORTANT NOTE: the 5HD-HUB unit, P/N: 288250025, is supported by ConquerorPRO version 12.13.06
or higher.
The 4HD-HUB and the 5HD-HUB are the interfaces between the 4HD/5HD-CPU, the LCOM devices
(pinspotter interfaces, camera, etc…) and all the other 4HD/5HD devices (such as the console) with the
scoring network. The main functionalities of these units are to act as a network hub and supply power for
all the devices connected to it, except for the main (or slave) scoring network switch connected to the N1
connector, that does not take power from the 4HD/5HD-HUB unit, so the turning on or off of these units
(by the plugging or unplugging of the power cord) will result in the turning on or off of the entire pair of
lanes. These units have to be installed on the rear side of the curtain wall (or on the aisle between each pair
of pinspotters, if 90 XLi with CE safety kit are present).
There are two different versions for the 4HD-HUB unit. The last version is called “4HD-HUB Rev.3”. The
main difference between the 4HD-HUB Rev.3 unit and the previous versions is the absence of the D1 and
D2 ports on the 4HD-HUB Rev.3. During this manual we will refer to the “4HD-HUB Rev.3” as “4HD-HUB”
for simplicity.
1.1.1 -Installation notes
The 4HD/5HD-HUB is the input/output device for the scoring system.
This unit communicates with the front desk via a standard network by the N1 connector and is connected
to all other devices by a standard network with POE (Power Over Ethernet). NEVER connect, for any reason,
a standard network device (such as a network switch) to a port different than the N1 port. Connecting a
standard network device to a port different than N1 may result in major damages for the device or for the
4HD/5HD-HUB unit itself.
The 4HD/5HD-HUB unit must be installed on the curtain wall, between the pair of pinspotters, in an easily
accessible position.
If the installation on the curtain wall is not possible, the 4HD/5HD-HUB unit can be placed on the wall
behind the pinspotters.
If 90 XLi pinspotters with safety kit are present, install the 4HD/5HD-HUB on the panel located at the end of
the aisle present between each pair of pinspotter, as explained in the table T.20.083.
The connection between the 4HD/5HD-HUB and the 4HD/5HD-CPU or the console are made with different
cables according to the distance between the units:
Up to 50 m (up to 150 ft.): one AWG-24 Cat. 5e network cable;
More than 50 m (more than 150 ft.): one solid AWG-23 Cat. 6 cable.
These cables are provided by QubicaAMF.

BES X Installation Manual, Rev.9, Jun 2018 System components
P/N: 400288005 11
1.1.2 -5HD-HUB label description
The image above displays the label located on the side of the 5HD-HUB unit.
1. Manufacturer (QubicaAMF Europe S.p.A.);
2. Part number (P/N: 288250025);
3. List of certifications (CE certification);
4. Name of the unit (5HD-HUB);
5. Electrical notes (100-240 V; 1.3-0.6 A; 50/60 Hz);
6. Serial number with bar code.
1.1.3 -4HD-HUB label description
The image above displays the label located on the side of the 4HD-HUB unit.
7. Manufacturer (QubicaAMF Europe S.p.A.);
8. Part number (P/N: 288250021 or 288250018 or 288250014);
9. List of certifications (CE certification);
10. Name of the unit (4HD-HUB Rev.3);
11. Electrical notes (100-240 V; 1.3-0.6 A; 50/60 Hz);
12. Serial number with bar code.
1.1.4 -Connections
Power Specifications for the 4HD/5HD-HUB are: 100-240 V; 1.3-0.6 A; 50/60 Hz.
On the 4HD-HUB the following connections are available:
Connectors on the left side of the 4HD-HUB unit:
L1 CPU COM line: Network connection with POE for the 4HD/5HD-CPU.
L2 Powered COM line: Currently not used.

System components BES X Installation Manual, Rev.9, Jun 2018
12
12 P/N: 400288005
L3 ODD console COM line: Network connection with POE for the odd lane console (EasyKey or
SuperTouch models only). When a single console per pair of lanes is installed, this output is not
used.
L4 EVEN/SINGLE console COM line: Network connection with POE for the even lane console
(EasyKey or SuperTouch models only). This output is always used when the console have to be
installed, even in the case of single console per pair of lanes.
PRESENT ONLY ON THE 4HD-HUB: P1 LCD console backlight: Power out for SuperTouch console
backlights NOT used with SuperTouch Ver.2 consoles (P/N: 288150026).
PRESENT ONLY ON THE 4HD-HUB Rev.2: D1 Console Data ODD: For OLD console only. Power
supply, XCOM and input / output audio channels for the odd lane console (Micro I, Micro II or Fly
console models only). When a single console per pair of lanes is installed, this output is not used.
PRESENT ONLY ON THE 4HD-HUB Rev.2: D2 Console Data EVEN / SINGLE: For OLD console only.
Power supply, XCOM and input / output audio channels for the even lane console (Micro I, Micro II
or Fly console models only). This output is always used when the console have to be installed, even
in the case of single console per pair of lanes.
PRESENT ONLY ON THE 5HD-HUB: D1 Pinspotter COM line: Connection to TMS pinspotter chassis.
PRESENT ONLY ON THE 5HD-HUB: D2 YCOM COM line: Connection for Control I/O 3 ONLY.
Connectors on the upper side of the 4HD-HUB unit:
N1 Network:Standard network connection to the scoring network.
4HD-HUB LEDs:
Each RJ45 port is provided of two colored LED (orange and green).
N1:
oGreen: The LED is ON when a link is present.
oOrange: The LED flashes when is transmitting or receiving data from the network.
L1, L2, L3 and L4:
oGreen: Power Over Ethernet status. When the LED is ON, it indicates the 4HD-HUB is
providing the correct power over Ethernet to the connected device.
oOrange: The LED flashes when is transmitting or receiving data from the network.
4HD-HUB D1 and D2:
oGreen: Power output status. When the LED is ON, it indicates the CPU is providing the
correct power to the connected device
oOrange: XCOM communication line. The LED flashes when the XCOM line is running.
5HD-HUB D1 and D2:
oTx: The LED flashes when transmitting data from the connected device.
oRx: The LED flashes when receiving data from the connected device.
1.1.5 -How the 4HD/5HD-HUB works
The communication between the 4HD/5HD-HUB unit and the front desk is based on the TCP/IP protocol.
The operation of the 4HD/5HD-HUB is similar to a normal network hub, with the additional functionality to
give power to all the lane devices (4HD/5HD-CPU, SuperTouch, EasyKey, pinspotter interface, etc.)
connected to it. The turning on/off of the 4HD/5HD-HUB will be the turning on/off of the entire pair of
lanes devices (4HD/5HD-CPU, SuperTouch, EasyKey, pinspotter interface, etc.).

T. 0.2 107
JUN 5th 1820
288250025
5HD-HUB
LCom
C1
B
+
A
_
L4
Even/Single
Console
Com Line
L3
Odd
Console
Com Line
L2
Powered
Com Line
L1
Cpu
Com Line
D1
Pinspotter
Com Line
Tx Rx
D2
YCom
Com Line
Tx Rx
Disconnect supply before servicing
Couper L'alimentation avant toute
intervention manuelle
Risk of electric shock
Risque d’électrocution
Power Input
Range: 100-240V - 50-60 Hz
Network
N1
Warning:No User Servi-
ceable Parts Inside,
Contact Authorized De-
aler for Assistance.
Warranty Voided if Se-
als Are Broken.
Provide an Earthing con-
nection before the mains
plug is connected to the
mains. When disconnect-
ing the earthing connec-
tion, be sure to disconnect it
by pulling out the mains plug
from the mains.
Attention: Ne pas ouvrir l’appa-
reil. Il n’y a aucune pièce répa-
rable à l’intérieur. Confiez tou-
te réparation à un personnel
autorisé. Le garantie expire si
l’étiquette a été altérée.
GH： このKには
ユーザーでOPできる
RSはありません。
このボックスを\けた
>?は、いかなる`aも
cdしません。
!"プラグを'(する+に
アース0が'(されている
のを78してください。
アース0を=す>?は、
Bず!"プラグを
Dいてから=してください。
5HD HUB-
Front View
L1 - 4 /5HD- connectionHD CPU
L2 - Currently Not Used
L3 - Odd lane console lineCOM
L4 - Even/Single lane console lineCOM
D1 - Pinspotter COM line
LCOM
5HD HUB-
Upper View
N1 - Scoring network
Dimensions
Heigth
Length
Depth
Weight
300 mm
170 mm
65 mm
1800 g
11” 13/16
6” 3/4
2” 9/16
4 lbs
D2 - YCOM COM line

T. 0.2 102
APR 27th 1720
288250021
4HD-HUB REV.3
Network
N1
Warning: No User Service-
able Parts Inside, Contact
Authorized Dealer for As-
sistance. Warranty Voided
if Seals Are Broken
Provide an Earthing conne-
ction before the mains plug
is connected to the mains.
When disconnecting the
earthing connection, be su-
re to disconnect it by pulling out
the mains plug from the mains.
GH： このKにはユーザーで
OPできるRSはありません。
このボックスを\けた?@は、
いかなる`aもcdしません。
!"プラグを'(する+に、
アース1が'(されているのを
89してください。アース1を
>す?@は、Bず!"プラグを
Dいてから>してください
Attention: Ne pas ouvrir l’appareil.
Il n’y a aucune pièce réparable à
l’intérieur. Confiez toute répara-
tion à un personnel autorisé.
Le garantie expire si l’étiquette a
été altérée.
LCOM
C1
_
A
B
+
P1
LCD CONSOLE
BACKLIGHT
L4
EVEN SINGLE/
CONSOLE
Com Line
L3
ODD
CONSOLE
Com Line
L2
Powered
Com Line
L1
CPU
LineCOM
Power Input
Range: 100-240V - 50-60 Hz
Disconnect supply before servicing
Couper L'alimentation avant toute
intervention manuelle
Risk of electric shock
Risque d’électrocution
4 -HD HUB
Front View
L1 - 4 /5HD- connectionHD CPU
L2 - Currently Not Used
L3 - Odd lane console lineCOM
L4 - Even/Single lane console lineCOM
P1 - Power out for console back lightsLCD
LCOM
4 -HD HUB
Upper View
N1 - Scoring network
Dimensions
Heigth
Length
Depth
Weight
300 mm
240 mm
65 mm
3000 g
11” 13/16
9” 1/2
2” 9/16
6.6 lbs

T. 0.02 76
APR 27th 1720
288250018
4HD-HUB
Console
Data
ODD
Console
Data
/SingleEVEN
LCOM
D1
D2
C1
_
A
B
+
P1
LCD CONSOLE
BACKLIGHT
L4
EVEN SINGLE/
CONSOLE
Com Line
L3
ODD
CONSOLE
Com Line
L2
Powered
Com Line
L1
CPU
LineCOM
Power Input
Range: 100-240V - 50-60 Hz
Disconnect supply before servicing
Couper L'alimentation avant toute
intervention manuelle
Risk of electric shock
Risque d’électrocution
Network
N1
Warning: No User Service-
able Parts Inside, Contact
Authorized Dealer for As-
sistance. Warranty Voided
if Seals Are Broken
Provide an Earthing conne-
ction before the mains plug
is connected to the mains.
When disconnecting the
earthing connection, be su-
re to disconnect it by pulling out
the mains plug from the mains.
GH： このKにはユーザーで
OPできるRSはありません。
このボックスを\けた?@は、
いかなる`aもcdしません。
!"プラグを'(する+に、
アース1が'(されているのを
89してください。アース1を
>す?@は、Bず!"プラグを
Dいてから>してください
Attention: Ne pas ouvrir l’appareil.
Il n’y a aucune pièce réparable à
l’intérieur. Confiez toute répara-
tion à un personnel autorisé.
Le garantie expire si l’étiquette a
été altérée.
4 -HD HUB
Front View
L1 - 4 /5HD- connectionHD CPU
L2 - Currently Not Used
L3 - Odd lane console lineCOM
L4 - Even/Single lane console lineCOM
P1 - Power out for console back lightsLCD
D1 - Data for Odd lane console (old console)XCOM
D2 - Data for Even lane/single console (old console)XCOM
LCOM
4 -HD HUB
Upper View
N1 - Scoring network
Dimensions
Heigth
Length
Depth
Weight
300 mm
240 mm
65 mm
3000 g
11” 13/16
9” 1/2
2” 9/16
6.6 lbs

System components BES X Installation Manual, Rev.9, Jun 2018
16
16 P/N: 400288005
1.2 - 4HD-CPU and 5HD-CPU
IMPORTANT NOTE: the 5HD-CPU unit, P/N: 288250023, is supported by ConquerorPRO version 12 or
higher.
The 4HD-CPU and 5HD-CPU are the graphic engine of the BES X scoring system. Their functionality is to
display the scoring grids, the animations, the different environments, etc… They are connected to the
4HD/5HD-HUB unit with a single network cable and must be installed near the overhead monitors.
These units can manage up to two independent video outputs for the scoring system, but can control
(monitor ON/OFF, channel change, etc. only on supported monitors) up to three monitors (two for the
scoring system and one with an independent video signal). They communicates and takes power from the
4HD/5HD-HUB unit through the network cable connected to the L1 connector and are connected to the
overhead monitors through the HDMI connectors. These units must be installed near the overhead
monitors, in particular the 4HD-CPU and the 5HD-CPU must be installed on the monitor frames if the
monitor frames are supplied by QubicaAMF. If the monitor frames are not supplied by QubicaAMF, the
4HD-CPU or the 5HD-CPU unit shall be fixed to a vertical surface NEAR the overhead monitors, in an area
that ensures the correct air recirculation, with the L1 connector facing upwards.
There are two versions for the 4HD-CPU unit with part numbers: 288250017 and 288250020.
There is one version of the 5HD-CPU unit, with part number: 288250023.
1.2.1 -Installation notes
The 4HD/5HD-CPU unit communicates with the 4HD/5HD-HUB via a standard network with POE. The
connection between the 4HD/5HD-CPU and the 4HD/5HD-HUB is between the L1 port of the 4HD/5HD-CPU
unit and the L1 port of the 4HD-HUB, as explained in this manual.
In the case of monitors and monitor frames provided by QubicaAMF the 4HD/5HD-CPU unit must be
installed on the monitor frames. If the monitor frames are not supplied by QubicaAMF, the 4HD/5HD-CPU
unit shall be fixed to a vertical surface NEAR the overhead monitors, in an area that ensures the correct air
recirculation, with the L1 connector facing upwards.
The connection between the 4HD/5HD-HUB and the 4HD/5HD-CPU is made with a different cable,
according to the distance between the units:
Up to 50 m (up to 150 ft.): one AWG-24 Cat. 5e network cable;
More than 50 m (more than 150 ft.): one solid AWG-23 Cat. 6 cable.
These cables are provided by QubicaAMF.

BES X Installation Manual, Rev.9, Jun 2018 System components
P/N: 400288005 17
1.2.2 -5HD-CPU Label description
The image above displays the label located on the side of the 5HD-CPU unit.
1. Manufacturer (QubicaAMF Europe S.p.A.);
2. Name of the unit (5HD-CPU);
3. Part number with bar code (P/N: 288250023);
4. List of certifications (CE certification);
5. Serial number with bar code.
6. Electrical specifications (12 VDC Max 30W Ext. Pow.Plug)
1.2.3 -4HD-CPU Label description
The image above displays the label located on the side of the 4HD/5HD-CPU unit.
7. Manufacturer (QubicaAMF Europe S.p.A.);
8. Name of the unit (4HD-CPU);
9. Part number with bar code (P/N: 288250020 or 288250017);
10. List of certifications (CE certification);
11. Serial number with bar code.
12. Electrical specifications (12 VDC Max 33W Ext. Pow.Plug)

System components BES X Installation Manual, Rev.9, Jun 2018
18
18 P/N: 400288005
1.2.4 -Connections
On the 4HD/5HD-CPU the following connections are available:
Connectors on the upper side of the 4HD/5HD-CPU unit:
EXTERNAL POWER SUPPLY: AC/DC external power supply. Not used when the 4HD/5HD-CPU is
used for score purposes.
L1: Network connection to the 4HD/5HD-HUB unit.
U1: Currently not used.
U2: Currently not used.
Connectors on the upper side of the 4HD/5HD-CPU unit:
EVEN CTRL: Serial control for the even lane overhead monitor. Only for supported monitors.
EVEN HDMI: Digital video output for the even lane overhead monitor. The control through the
HDMI connector works only on supported monitors (actually on AccuVision Gen.3 and Gen.4).
AUX CTRL: Serial control for the third overhead monitor. Only for supported monitors.
4HD-CPU ONLY: AUX HDMI: HDMI control ONLY for the third overhead monitor. The control
through the HDMI connector works only on supported monitors (actually on AccuVision Gen.3 and
Gen.4).
ODD CTRL: Serial control for the odd lane overhead monitor. Only for supported monitors.
ODD HDMI: Digital video output for the odd lane overhead monitor. The control through the HDMI
connector works only on supported monitors (actually on AccuVision Gen.3 and Gen.4).
4HD/5HD-CPU LEDs:
The L1 network port is provided of two colored LED (both LEDs are green). The LED on the top left angle of
the port, is ON with an active link and OFF if it is disconnected. The LED on the top right angle will blink with
the activity of the network.
1.2.5 -How the 4HD/5HD-CPU works
The communication between the 4HD/5HD-CPU unit and the 4HD/5HD-HUB is based on the TCP/IP
protocol.
Thus 4HD/5HD-CPU units have an IP address that changes depending on the number of the pair of lanes
where they are installed. E.g., the address is 192.168.216.101 for the pair no. 1, 192.168.216.102 for the
pair no. 2, …….3 for the pair no. 3 and so on.
This information is displayed on the lane monitors during the booting process, when testing the devices,
together with the information concerning the version of programs loaded on the 4HD/5HD-CPU and the
serial number, that is an univocal number that identifies the 4HD/5HD-CPU unit. The serial number is used
to address the 4HD/5HD-CPU units, it can be read on the lane monitors and on a specific label applied on
one side of the 4HD/5HD-CPU unit.