Queclink GV600 Series User manual

Installation Manual of GV600 Series
Version: 2.0
http://www.queclink.com
[e-mail]

Contents
Screw installation instructions………………………………….…….………….…………….……..3
Kit Contents………………………………….…….………….……..…………………………..…………...4
Installation on Vehicle ……………………………………………………………..………………..……5
Mounting Configures ……………………….………….………………………………………..…...… 5
Routing of GV600 Device Wire Harness………………………………………………………......6
External Power Connection………………………………………………………………….…….…....7
LED Status of Device …………………………………………………………………………..…..….......8
Installation Manual of GV600 Series
Queclink
Confidential

Installation Manual of GV600 Series
Screw installation instructions
Step1: Install the two screws on the front
Step2: Install and tighten 4 screws on the bottom shell
Note: Install the screws in opposite angles order. Do not fully tighten the screws at the
beginning. When all four screws are installed, then fully tighten them. Otherwise, the
waterproof capability may be deteriorated due to uneven tightening.
Queclink
Confidential

Kit Contents:
•Tracking Device (internal antenna ) x1
•18 Pin Power Harness x1
•Temperature Sensor x1
WIRE DESCRIPTION
Mounting Hardware:
Manage USB Data Cable(Optional):
•Manager USB cable x1 ----------------for configuration GV600W series
Type Picture Hardware Contents
Adhering Mounting self-drilling screws x2
Covert Mounting
(Not include)
Mounting Bracket x1
Serrated flange nuts x2
Flat head screws x4
Definition Color PIN No Connector PIN No Color Definition
PWR1 Red 12Red/ Green PWR2
AGND Black 34Black AGND
IGN White 56Green ADIN1
OUT-3V3 Red/ White 78Black/White GND
1-WIRE Gray 910 NC NC
OUT/IN1 Blue 11 12 Yellow OUT/IN2
OUT/IN3 Brown 13 14 Orange OUT/IN4
EX_RX Purple 15 16 Purple/White EX_TX
RXD Pink 17 18 White/Black TXD
Installation Manual of GV600 Series
3
Queclink
Confidential

Installation on Vehicle
Please install GV600 device to the Flatbed, Chassis and Tanker etc.
Flatbed: Inside a forward frame rail or under the trailer floor.
Chassis: Inside a forward frame rail with the harness side facing the trailer harness.
Tanker: For most tankers, the best mounting location for GV600 device is behind the plate that the trailer’s cable
receptacle so as to be easy mounted on.
NOTE: When installing the GV600 tracker, it is better to put it to a good signal covering position.
CAUTION: Please do not drill holes and install it on the tanker directly.
Find a mounting location in a frame rail or under the trailer floor, with wire
routing access that will allow the GV600 Series device
towards to a good signal covering position.
Use either of the mounting plate methods(refer to next page)
to install GV600 device to the trailer.
Use two self-drilling screws that can be easy to mount the GV600 device to
the flatbed’s wood floor.
Find a mounting location under a gusset on the driver’s side frame rail,
with wire routing access that will allow the
GV600 device towards to a good signal covering position.
Use either of the mounting plate methods
(refer to next page) to install GV600 device to the trailer.
Make sure the harness side of the GV600 towards to the trailer harness of
the driver side frame rail.
Draw two holes on the mounted plate
Drill holes for screw installation
Install GV600 to the plate, with the
cable connector towards to the ground
Installation Manual of GV600 Series
4
Queclink
Confidential

Mounting Configures
Plate Mount, convert (Welded):
Nose Mount :
Use the GV600 Mounting plate as a template, mark four holes with a
pencil for mounting holes
Drill mounting holes with a #29 drill bit
Screw the plate to the chassis by using the Flat head screws x4
Secure the GV600 to the mounting plate, with the supplied Serrated
flange nuts x2
Cable connector end should towards to the ground.
Weld the GV600 mounting plate into place
Weld the full length of the tap
Don’t weld the entire plate
Weld here
Weld here
Place the GV600 device on the forward facing bulkhead, harness-side down
Fix the GV600 device with two screws
Installation Manual of GV600 Series
5
Queclink
Confidential

Routing GV600 Device Wire Harness
Nose Mounting in trailer:
Mounting in Flatbed and chassis:
Mounting in tanker:
Remove the bolts and open the housing’s cover
Choose the best harness routing way
Run alongside the trailer harness through the housing’s stock cable
grommet.
Install cable clamps to secure the harness to trailer
Remove the bolts and pull the cover away from the housing
Route the GV600 device wire harness alongside the trailer harness
through the housing’s stock cable grommet
Use the zip ties and cable clamps to fix the wire harness to the
trailer harness and trailer
Remove the bolts and open the housing cover
Feed the device harness through the housing’s stock cable grommet
Note:
For special installation, please contact
Queclink’s technical support team
first.
Installation Manual of GV600 Series
6
Queclink
Confidential

External Power Connection
Connect the power wire (Red) and ground wire (Black) to the external power supply
Important note: If you want to use accessory which GV600 support, please refer the GV600
series User Manual.
There are two pairs of power cable (PWR & AGND) that are included in the 18pin wire harness. You
can select a pair of power cable (PWR & AGND) and use it to connect to external power.
Chose one of the PWR cable (PWR1 or PWR2) to connect external power
PWR1
AGND
PWR2
AGND
Installation Manual of GV600 Series
7
Queclink
Confidential

LED Status of Device
LED Lighting Definition:
Note 1: CELL LED cannot be configured
Note 2: GPS LED and PWR LED are configurable to turn off by using the manage tool.
Note 3: Fast flashing: for CELL LED is about 100 ms ON/800 ms OFF; for GPS LED and PWR LED is
about 100 ms ON/100 ms OFF
Note 4: Slow flashing: for CELL LED is about 100 ms ON/2000 ms OFF; for GPS LED and PWR LED is
about 600 ms ON/600 ms OFF
LED Device status LED status
CELL
(Note 1)
Device is searching CELL network. Fast flashing (Note 3)
Device has registered to CELL network. Slow flashing(Note 4)
Modem power shutdown. OFF
SIM card needs pin code to unlock. ON
GPS
(Note 2)
GPS chip is powered off. OFF
GPS sends no data or data format error occurs. Slow flashing
GPS chip is searching GPS info. Fast flashing
GPS chip has gotten GPS info. ON
PWR
(Note 2)
No external power and internal battery voltage is lower than 3.35V. OFF
No external power and internal battery voltage is below 3.5V. Slow flashing
External power in and internal battery is charging. Fast flashing
External power in and internal battery is fully charged. ON
PWR
GPS
CEL
Installation Manual of GV600 Series
8
Queclink
Confidential