Quest Controls TELSEC MP1 User manual

Rev 3.0 9/15/22
TELSEC® MP1
User Guide

Rev 3.0 9/15/22
CRITICAL APPLICATIONS DISCLAIMER
QUEST PRODUCTS ARE NOT INTENDED OR AUTHORIZED FOR USE IN ANY APPLICATION THAT REQUIRES
FAIL-SAFE OPERATION, OR ANY SYSTEM THAT IS RESPONSIBLE FOR PROVIDING DETECTION,
MONITORING OR CONTROL OF CRITICAL SAFETY, LIFESAVING OR LIFE-SUPPORT CONDITIONS,
FUNCTIONS OR OPERATIONS (INCLUDING BUT NOT LIMITED TO FIRE DETECTION, ALARMING, OR
SUPPRESSION), OR ANY APPLICATION WHEREIN A FAILURE OR MALFUNCTION OF THE PRODUCT MAY
LEAD TO SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE, PERSONAL INJURY OR DEATH.
Lithium Battery Notice
Replace Battery with Panasonic CR2032 or equivalent Lithium Battery (Quest PN 250034), rated at 3
Vdc. Use of another battery may present a risk of fire or explosion.
CAUTION - Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
COPYRIGHT NOTICE
Copyright © 2022 by Quest Controls, Inc. (Quest). The material discussed in this publication is the
proprietary property of Quest. Quest retains all rights to reproduction and distribution of this
publication.
Specifications are subject to change without notice.

Rev 3.0 9/15/22
Revision History
Date
Rev #
Modifications
By:
9/15/22
3.0
Updates for features in Build #22 9/12/22:
•Password rules for http, SSH/Telnet and SNMPv3
•TL1 type addition for alarms
•Support for 8 Time Schedules
K. Nickel
05/11/22
2.2
Additional clarification on defining input 7 for power monitoring
K. Nickel
04/20/22
2.1
Minor update to the specification section
K. Nickel
10/29/21
2.0
Updated to support new features and web page organization in
Build # 20
K. Nickel
03/24/21
1.0
Initial release
K. Nickel

Rev 3.0 9/15/22
Table of Contents
1 Overview...............................................................................................................................................1
1.1 Getting Started..............................................................................................................................1
2 Product Specifications...........................................................................................................................2
3 Installation ............................................................................................................................................3
3.1 Mounting the MP1........................................................................................................................3
3.2 Powering and Grounding ..............................................................................................................4
3.3 Connecting the Ethernet...............................................................................................................4
3.4 Wiring inputs.................................................................................................................................4
3.5 Wiring Outputs..............................................................................................................................9
4 Local Operation...................................................................................................................................10
4.1 Power LED ...................................................................................................................................10
4.2 Alarm LED....................................................................................................................................10
4.3 Relay Outputs..............................................................................................................................10
4.4 Restoring to Factory Defaults .....................................................................................................10
5 Communicating with the MP1 ............................................................................................................11
5.1 Connecting to the System...........................................................................................................11
5.2 Web Page Navigation..................................................................................................................11
6 System Status......................................................................................................................................12
6.1 Input Status.................................................................................................................................12
6.2 Output Status..............................................................................................................................14
6.3 Alarm Status................................................................................................................................14
6.4 Active Alarm Log .........................................................................................................................15
6.5 Historical Alarm Log....................................................................................................................15
6.6 Log Data ......................................................................................................................................17
7 Bypassing ............................................................................................................................................18
7.1 Bypass Inputs ..............................................................................................................................18
7.2 Bypassing Outputs ......................................................................................................................19
8 Configuring the MP1...........................................................................................................................20
8.1 System Setup...............................................................................................................................20
8.2 Alarm Dispatch Settings..............................................................................................................26
8.3 HTTP User Administration...........................................................................................................28
8.4 Advanced Settings.......................................................................................................................29
9 Programming the System....................................................................................................................32
9.1 Input Programming.....................................................................................................................32

Rev 3.0 9/15/22
9.2 Output Programming..................................................................................................................34
9.3 Alarm Programming....................................................................................................................36
9.4 Time Schedules ...........................................................................................................................41
10 Shell Commands..................................................................................................................................43
10.1 Set IP Command..........................................................................................................................43
10.2 Set MTU Command.....................................................................................................................44
10.3 Set httppswd Command .............................................................................................................44
10.4 Set snmpmgr Command .............................................................................................................44
10.5 Upgrade URL ...............................................................................................................................45
10.6 Checking for Upgrades................................................................................................................45
10.7 Ping Command............................................................................................................................45
10.8 Exit & Logout Command .............................................................................................................46
11 File Upload Format..............................................................................................................................46
11.1 Section Formats ..........................................................................................................................46
11.2 Uploading config files..................................................................................................................49
12 SNMP Sets & Gets...............................................................................................................................50
12.1 Public SNMPv2............................................................................................................................50
12.2 Input table...................................................................................................................................50
12.3 Alarm point table ........................................................................................................................50
12.4 Output table................................................................................................................................51
12.5 Active alarm point table..............................................................................................................51
12.6 Scalar values................................................................................................................................52
13 Troubleshooting..................................................................................................................................53
13.1 Power Up.....................................................................................................................................53
13.2 Communication...........................................................................................................................53
13.3 Sensor Reading............................................................................................................................53
13.4 Control Point Failure...................................................................................................................53
13.5 Alarm Notification Failure...........................................................................................................54
13.6 Battery.........................................................................................................................................54
Appendix A - SNMP Trap Format ................................................................................................................55
Appendix B - RADIUS Server Configuration ................................................................................................56
Appendix C –Email Alarm Format ..............................................................................................................57
Appendix D –TL1 Alarms and Commands..................................................................................................58
Contact Information....................................................................................................................................61

Rev 3.0 9/15/22 - 1 - TELSEC©MP1 User Guide
1Overview
The TELSEC®MP1 is designed to provide advanced monitoring and alarming for remote facilities and
cabinets using industry standard communications protocols such as SNMP and SMTP (Email) over
Ethernet. The system has a built-in web server for status review and programming and can be polled
using SNMP GET requests. The MP1 has six universal inputs for monitoring temperature, humidity,
contact closures and any 0-6 VDC or 0-20 mA sensors. The MP1 also monitors the incoming voltage to
the unit and displays the value as the seventh input. Each individual input may be scaled and displayed
in the proper engineering units. The MP1 has two digital outputs which can be actuated based upon
user programmable events or actuated remotely through the web server or SNMP. This user guide is
intended to provide basic operational information for programming and status review of the MP1
System. Please contact Quest Controls for additional information and or questions about the operation
of the system.
1.1 Getting Started
The TELSEC®MP1 is simple to setup and program which allows you to start monitoring your facility
quickly. The basic steps are listed below along with a chapter reference for this manual:
1. Mount the MP1 in the desired location (section 3.1)
2. Power the system. (section 3.2.1)
3. Connect the inputs to be monitored to the system. (section 3.4)
4. Wire the digital outputs. (section 3.5)
5. Connect the MP1 to an Ethernet switch and configure the IP settings. (section 5.1)
6. Configure the system (Section 8.1)
7. Configure the alarm distribution. (section 8.2)
8. Define the inputs. (section 9.1)
9. Define the alarm points. (section 9.3.1)

Rev 3.0 9/15/22 - 2 - TELSEC©MP1 User Guide
2Product Specifications
Specifications
Part number: 151095
▪Inputs: six universal inputs supporting 0-5 VDC, 4-20 mA, thermistor & contact closure. One
Input (UIN 7) to monitor monitoring 18-60 VDC
▪Outputs: two Form C digital outputs. Contact rating: 0.5 A @ 60 VDC
▪Network interface: Ethernet 10/100 Base-T
▪Protocols supported: IPv6, IPv4, HTTP, HTTPS, RADIUS Password Authentication, NTP, SMTP
(email), SNMP v1, v2c and v3 for Gets, Sets and traps/informs
▪Logging: Logs data for inputs, outputs and alarms
▪Alarm notification methods: TL1, Email and SNMP traps or informs
▪Alarm destinations: four programmable trap destinations, nine email addresses or distribution
lists
▪I/O terminal: spring loaded terminals supports 16 -24 AWG wire
▪Power: 24-48 VDC, 3.7 W max.
▪Battery: long life lithium (PN 250034) 3 VDC*
▪Ambient operating temperature: -4° to 140°F (-20° to 60°C), 0-95% RH Non-condensing
▪Certification: UL, cUL, FCC 47 CFR Part 15B, ISED ICES-003 Class A
▪Dimensions: 8.2”L x 4.7”W x 1.7”D (208 x 119 x 43 mm)
▪Weight: 0.9 lb. (408 g)
▪Warranty: 1 Year
Specifications subject to change without notice

Rev 3.0 9/15/22 - 3 - TELSEC©MP1 User Guide
3Installation
All local and national electrical safety codes (NESC®) must be followed when installing the MP1. If there
is any contradiction in this manual and those standards, then the installer must follow the local and
national codes. Use copper conductors only.
3.1 Mounting the MP1
Install the MP1 in the desired location using appropriate hardware to connect the two mounting tabs to
the wall.
8.2" (208mm)
4.7" (119mm)
7.3" (185mm)
Figure 1 - TELSEC®MP1 Dimensions

Rev 3.0 9/15/22 - 4 - TELSEC©MP1 User Guide
3.2 Powering and Grounding
3.2.1 Powering the MP1
Follow all national and local electrical codes when powering the MP1. Quest recommends a minimum
of 18 AWG conductor for powering. The TELSEC®MP1 will operate from 18-60 VDC power (50 mA max
at 48 VDC). The power input is isolated from the rest of the system and will work on either a positive or
negative DC system. Connect the power source to the MP1 observing the polarity markings on the
enclosure. Quest recommends fusing the power source at 1 A. Reverse polarity will not damage the
unit, but it will not operate until corrected. It is recommended that all input wiring be completed with
no power to the system. The terminals are spring loaded. Press on the orange button to release the
spring and then insert the wire. Turn on power once all wiring is verified.
3.2.2 Removing the Battery Insulator
The MP1 is shipped with an insulator to keep the battery disengaged from the system. Remove the
insulator once the unit is permanently powered, by pulling the tab in front of the unit. The system uses
the battery to save the system time and input timer status.
3.2.3 Grounding the MP1
There is a ground terminal on the power connector. Place a ground wire using a minimum 12 AWG
conductor from the Electrical panel ground bus (or other approved grounding point) to the ground
terminal on the MP1. Follow national and local codes and practices for properly grounding the system.
3.3 Connecting the Ethernet
Use a standard Cat5 Ethernet cable to connect the MP1 to the local switch or hub. Configure the switch
port to auto speed detect and auto negotiation. A green LED link light on the ethernet jack will be
illuminated when a physical link has been established. The amber LED on the ethernet jack will be
illuminated when the connection is 100Mb and off if the connection is 10Mb.
3.4 Wiring inputs
Wire each input to be used between the input terminal (1-6) and a common terminal (C). Refer to the
silkscreen on the enclosure for location of each input and common terminal. The terminals support 16-
24 AWG wire and are spring loaded. Press on white button to release the spring and then insert the
wire. The inputs will support any sensor that is a 10k Type III thermistor: 0-6 VDC or 0-20 mA analog
sensors. In addition, the system accepts dry contact closures or wet contact closures up to 65 VDC.

Rev 3.0 9/15/22 - 5 - TELSEC©MP1 User Guide
3.4.1 Thermistors
Thermistors are resistive devices and do not have polarity. Connect one lead to the input terminal of
the desired input and the second lead to a common terminal. Quest recommends using shielded and
stranded cable for all analog sensors. Connect the shield of the cable to chassis ground on the MP1. Cut
the drain wire and isolate the shield at the sensor end of the cable.
Typical of all Quest thermistor
temperature sensors
Quest “Bullet Style” probe
Not polarity sensitive
Figure 2 - Thermistor Temperature Sensor Wiring