Rand McNally TND 750 User manual

QUICK START GUIDE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC SAR exposure limits set forth for an uncontrolled
environment.
SAR compliance for using the equipment in close proximity to the human body has been
evaluated at 0mm.
This equipment must not be co-located or operating in conjunction with any other antenna
or transmitter.
End-users and installers must be provide with antenna installation instructions and consider
removing the no-collocation statement.
Caution!
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This equipment should be installed and operated with a minimum distance of 0mm
between the radiator and your body.
Cet équipement devrait être installé et actionné avec une distance minimum de 0mm entre
le radiateur et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune
autre antenne ou émetteur.

2TND™750 Quick Start Guide
Your TND™750 Unit
Caution: Important Safety Information
Navigation
• Use this device at your own risk.
• Attend to this device only when it is safe to do so.
• Traffic laws and regulations always have priority over any
instructions from the navigation system.
NOTE: If you do not understand the spoken instructions or are unsure
of what to do, refer to the navigation map on your device.
Installation
• Make sure that the mount is securely mounted and properly
adjusted before each trip.
• Make sure that the mount does not impair the driver’s visibility.
• Do not attach the mount within the airbag deployment zone.
• Install the mount in a manner that minimizes risk in the event of
an accident.
• After installation, check all safety-related equipment to ensure that
it operates without interference from the device, its cables, or any
other accessories.
• Connect the vehicle charger to a 12V outlet only.
• The device can also be charged using a standard Micro USB charger.
Device
• Do not use sharp-edged objects on the device touch screen.
• The device is not waterproof and is not protected against
water damage.
• Protect the device from extreme temperatures. Operating
temperature for the device is between 32 degrees F and
120 degrees F.
• Do not open the device casing.
• Do not attempt to replace the battery. Contact Rand McNally
Customer Support with questions about the battery.
• Always follow local regulations when disposing of this device.
NOTE: Make sure that there are no kinks in the cable and that it will
not be damaged by any sharp objects.
NOTE: Use only a moist cloth to clean the device.
NOTE: Do not pull the cable to unplug the unit.

3TND™750 Quick Start Guide
Your TND™750
Box Contents
1TND™750 Unit
2Smart mount
3Bracket with suction cup
4Vehicle charger
5Micro USB cable
6Anti-glare screen protector
3
2
1
4
5
6

4TND™750 Quick Start Guide
Install the Mount
NOTE: Follow all local laws and regulations governing the placement of the mount.
1. Select an area with a line of sight to the sky and GPS satellites.
2. Clean and dry the mounting area.
3. Remove the suction cup protective film.
4. Attach the two pieces of the mount together and lock into place.
5. Adjust the angle of the mount.
6. Pull the suction cup lever up to release suction.
7. Plug the power cord into the mount and the vehicle's 12-volt power source.
8. Place and hold the mount suction cup against the mounting surface.
9. Press the suction cup lever down until it snaps into place.
10. Snap the tablet onto the mount.
11. Adjust the tablet so that it can be easily seen and
does not block the driver's line of sight.

5TND™750 Quick Start Guide
Your TND™750
DC in
(power)
AUX out
TND™750 Smart Mount
Micro
USB
TND™750
Home
Power Volume
Down Up
Micro
SD card
AUX
Port

6TND™750 Quick Start Guide
Getting Started
1. Connect to the Internet.
Connect to the Wi-Fi hotspot on your smartphone or
to your home Wi-Fi network.
2. Register your device with Rand McNally for updates
and support.
NOTE: You will be required to register your device in order
to receive new updates.
Transferring User Information from Previous Device
To move or export user data from a previous Rand McNally TND™device to a new Rand McNally TND™device,
please visit the following website for specific instructions: randmcnally.com/tnd750-support

7TND™750 Quick Start Guide
TND™750 Home Screen
43
1 2
5 6 8 79
1Settings: Opens Truck GPS preferences.
2Apps: View installed apps.
3Wi-Fi®indicator:Opens Wi-Fi®settings and displays
connection strength.
4Bluetooth®indicator: Opens Bluetooth®settings and
shows connectivity states.
5Volume indicator: Opens volume control.
6Brightness indicator: Opens brightness control.
7System update: Indicates if a system update is available.
Opens to initiate download.
8Current time: Displays current time.
9Battery power indicator: Displays current battery state.

8TND™750 Quick Start Guide
Features
1Truck Tools
Select to enter truck information, log your fuel and mileage,
and access other tools.
2Rand Navigation
Show location on the map and view navigation instructions.
3Guided Search
Choose a destination by History, Address Book, Points of
Interest, or Searching.
4DriverConnect
Record, view, and track duty status through your device.
Also includes hours of service timers, vehicle inspection
reports, and more.
421
3

9TND™750 Quick Start Guide
Restart Your TND™750
Rand McNally has designed TND™750 for speed and reliability. However, from time to time, all Android devices run into
problems. If your unit becomes unresponsive for any reason, it’s always best to restart the unit by turning it off and on
again.
Restarting the Device
1. Restart the unit by holding down the power button for 5 seconds, or until you see the Power Off screen.
2. Press Power Off.
3. Once the unit has shut down, press and hold the power button for 2 to 4 seconds to turn it back on.
If the unit is unresponsive and you don’t see the power down button appear on the screen, hold down the power button
for 10 to 15 seconds and the device will turn off completely. Once the unit has shut down, press and hold the power
button for 2 to 4 seconds to turn it back on.
For additional help and FAQs, visit randmcnally.com/support.

11TND™750 Quick Start Guide
1Route to a location.
2Select map view mode: Heading up,
North up or 3D view.
3Wi-Fi connected services.
4Zoom in/out.
5Return to current location.
6Virtual dashboard.
7Current street name, upcoming
intersection, or current location.
8Local time and Elevation.
9Settings: General, Truck Info, Route,
Map and Warnings.
10 Hide/display screen information and controls.
Rand Navigation
5
12
3
4
6 7 8 9 10

12 TND™750 Quick Start Guide
Rand Navigation > Truck Info and Warnings
Rand Navigation >Preferences
1. Tap Settings.
2. Tap the General, Route or Map tab.
3. Tap and to view options.
4. Tap the option button to be changed.
5. Enter new settings.
6. Tap to save changes.
On the left,
tap on an
option
On the left,
tap on an
option
On the
right,
enter
settings
for the
option
On the
right,
enter
settings
for the
option
1. Tap Settings.
2. Tap Truck Info or Warnings tab.
3. Tap and to view options.
4. Tap the option button to be changed.
5. Enter new settings.
6. Tap to save changes.

13TND™750 Quick Start Guide
Rand Navigation > Destination
1Route to a searched location.
Tips:
• Search for addresses, streets, cities and points of interest.
• Address searches should include either a city or postal code.
• Avoid using punctuations.
• Avoid using street prefixes and suffixes.
2Route to a New location.
3Plan a multi-stop trip or record a trail.
4Return to a previous location.
5Access the Address book.
6Route to a Point of Interest (POI).
7Return Home.
8Route to Work.
1
2 3 4 5
876

14 TND™750 Quick Start Guide
Rand Navigation > New Location
1. Tap Where to? > Guided Search > New location.
2. Tap Address.
3. Enter the name of the city. (Note: As you type, the
keyboard only displays the next possible letter.)
4. Results appear in the list. Tap the city to select.
5. Enter the street name. Tap the street name to select.
6. Enter the house number. Tap the address to select.
Tips
• You can also route to a new location by City center,
Intersection, Coordinates, or choose Address > Postal Code.
• View recent destinations by tapping
Where to? > Guided Search > History.
• View recent cities by tapping
Where to? > Guided Search > New location > Address.
• View saved locations by tapping
Where to? > Guided Search > Address book > Bookmarks.
• View saved trips by tapping Where to? > Guided Search > My trips.

15TND™750 Quick Start Guide
Rand Navigation > Confirm Destination Windows
1Create bookmark.
2Destination address.
3Coordinates.
4Cross reference to printed Rand McNally
Motor Carriers’ Road Atlas.
5Begin route to destination.
6Reorder locations
.
7Modify Route avoids, review Route details,
Overview and Save to My trips.
8Add a location.
9Review route details.
10 Compare the primary and alternate route(s)
and choose one.
11 Start route.
*To manage via points, Tap Where to? > Guided Search
> My trips > Multi-stop trips. You can add multiple
destinations in a multi-stop trip.
2
1
345
7
8
6
9
10
11

16 TND™750 Quick Start Guide
1Next maneuver instructions.
2Next maneuver street name or highway sign.
3Check upcoming exits for food, gas, hotels and other places.
4Route options.
5Select map view mode: Heading up, North up or 3D view.
6Wi-Fi connected services.
7Zoom in/out.
8Current speed (Note: Turns red for speed warnings).
9Posted speed limit. Tap to open a “Tell Rand” about speed limits.
10 Volume control.
11 Virtual dashboard.
12 Current street name, upcoming intersection, or current location.
13 Arrival time, remaining time, remaining distance or other options.
14 Settings: General, Truck Info, Route, Map and Warnings.
15 Hide/display screen information and controls.
Rand Navigation > Route Map Window
1
89
1211
2 3 4
5
6
7
10
151413

17TND™750 Quick Start Guide
Rand Navigation > Junction View
When on a route, Junction View displays when you have an
upcoming maneuver. Once past the maneuver, Junction View
closes and the previous window displays.
1Signs to follow for the next maneuver.
3Exit to follow for the next maneuver.
4Number and direction of lanes for the next maneuver.
5Distance to the upcoming maneuver. Distance decreases
as you approach the maneuver.
6Lane assist arrows.
7Dismiss Junction View.
12
34
5
6

18 TND™750 Quick Start Guide
Rand Navigation > Points of Interest (POIs)
With an active route, tap
Route Options > Search / Add a Stop >
Guided Search > POIs.
Search for a POI:
1Near your truck.
2In a particular city.
3Along your route.
4Near your destination.
POI Categories:
5Select a category.
6Search your custom POIs.
7Find popular truck-friendly POIs.
1 2
5
6 7
3 4

19TND™750 Quick Start Guide
Rand Navigation > POIs - continued
8Tap location to select.
9Search by name.
10 Search by available services.
11 Search Nearby, My destination or Along route. 8
910
11

20 TND™750 Quick Start Guide
Rand Navigation > Status and Milage
1. Tap Truck Tools > Status, Mileage & Fuel.
2. Tap the Status tab to view timers, odometer readings
and average speed.
3. Tap on a field to change or reset the number.
4. Tap the Mileage tab to view a list of mileage logs
by quarter.
5. Tap on a quarter to view individual logs.