Rand McNally Intelliroute TND-710 User manual

Quick Start Guide 2-19
Guide de démarrage rapide 21-39
Guía de Inicio Rápido 41-59
TND_710_Booklet_COVER_110921.indd 3 9/22/11 2:20 PM

1
TND_710_Booklet_INSIDE_110922.indd 1 9/22/11 2:07 PM

TO ENTER OR RETURN FROM STANDBY MODE: Press and release the Power Key.
IMPORTANT: Connect your device to your personal computer to register your device and activate additional features. Features require
internet connection and Windows-compatible PC.
FOR CUSTOMER SUPPORT, CALL 800-333-0136.
Overview
WARNING: See safety information included with the device for warnings and precautions.
To maximize battery life, plug in the navigation unit for the first 2 hours of use. Always make sure your GPS has a clear view of the sky.
The first time you use the device, it may take up to 15 minutes for your GPS to connect to the satellites.
TO POWER THE DEVICE:
On Press and hold the Power Key for two (2) seconds.
(Device powers on in 5 seconds.)
Off Press and hold the Power Key for five (5) seconds.
BATTERY POWER INDICATOR:
No Light
Device is running on the battery. Battery power is sufficient.
Green Device is plugged in and the battery is fully charged .
Red
Device is plugged in and the battery is charging.
2
TND_710_Booklet_INSIDE_110922.indd 2 9/22/11 2:07 PM

Power Key
Battery
Power
Indicator
NOTE: Use the Reset button (located on the side of the
device) to restore factory settings and restart the device.
3
TND_710_Booklet_INSIDE_110922.indd 3 9/22/11 2:07 PM

Main Menu
Enter truck information and access truck-specific use tools.
Show location on the map and view navigation instructions.
Change driver status.
Choose a destination.
Select TND™and route preferences.
Mute/unmute the speaker.
Adjust speaker volume.
Select the trailer load option.
When running on battery power, icon will indicate power status.
1
3
4
5
6
7
8
9
2
4
TND_710_Booklet_INSIDE_110922.indd 4 9/22/11 2:07 PM

1
3
4
567
89
2
5
TND_710_Booklet_INSIDE_110922.indd 5 9/22/11 2:07 PM

Install the Mount
NOTE: Follow all local regulations governing the placement of the mount.
Select an area with a line of sight to the sky and GPS satellites to ensure reliable GPS information.
Clean and dry the mounting area.
Remove the suction cup protective film.
Adjust the angle of the mount using the thumbscrew and slide the mount into the cradle.
Pull the suction cup lever up to release suction.
Place and hold the mount suction cup against the mounting surface.
Press the suction cup lever down until it snaps into place.
Angle the bottom of the device into the cradle and press the top of the device towards the cradle until you hear the upper clip latch into place.
Plug the power cord into the device and the vehicle’s 12-volt power source.
Adjust the navigation device so that it can be easily seen and does not block the driver’s line of sight.
1
3
4
5
6
7
8
9
2
6
TND_710_Booklet_INSIDE_110922.indd 6 9/22/11 2:07 PM

NOTE: Do not place
the mount in an airbag
deployment area.
7
TND_710_Booklet_INSIDE_110922.indd 7 9/22/11 2:07 PM

Set Warnings
Tap Truck Tools > Warnings.
Tap and to view all warning options.
Tap the option button to be changed.
Enter the new settings for the option.
Tap Back to save changes.
Enter Truck Information
Tap Truck Tools >Truck Info.
Tap and to view all options.
Tap the option button to be changed.
Enter new truck information settings.
Tap Back to save changes.
1
3
4
5
2
On the left,
tap on an
option
On the right,
enter settings
for the option
On the right,
enter settings
for the option
1
3
2
4
5
On the left,
tap on an
option
8
TND_710_Booklet_INSIDE_110922.indd 8 9/22/11 2:07 PM

View Timers and Logs
Countdown timers are controlled by the Driver Status (Driving,On Duty, or Off Duty) selected on the Main Menu.
Tap Truck Tools.
Tap Timers and Logs.
Tap the Timers tab to view timers,
odometer readings,and times.
Tap the Logs tab to view a list of
mileage logs by quarter.
Tap on a quarter to view individual
logs by state.
1
345
2
9
TND_710_Booklet_INSIDE_110922.indd 9 9/22/11 2:07 PM