Range Master Toledo FS Hob User manual

Users Guide
with
Installation & Service Instructions
U108900 - 02
FS

     

Warning
Accessible parts will become hot in use. To avoid burns and scalds children
should be kept away
You need clean fresh air - so does your hotplate. Burner flames produce
exhaust gases, heat and moisture. Make sure that the kitchen is well
ventilated: keep natural ventilation holes open or install a powered hotplate
hood that vents outside. If you have several burners on or use the hotplate
for a long time, open a window or turn on an extractor fan. For more detail
see the Installation Instructions.
We recommend you read ‘General Safety Instructions‘ (especially if you
have not used a dual fuel hotplate before) where we describe some basic
guidelines on how to use a dual fuel hotplate safely.

Make sure that the gas supply is turned on and that the hotplate is wired in
and switched on. The hotplate needs electricity.

When you first use your hotplate it may give off a slight odour. This should
stop after a little use.


Contents
Hotplate Burners Page 4
Warmer Page 5
The Griddle (optional extra) Page 6
The Wok cradle (optional extra) Page 7
Cleaning your hotplate Page 8
Troubleshooting Page 10
General Safety Instructions Page 10
Installation Page 12
Conversion to LP gas Page 17
Circuit Diagram Page 20
Technical Data Page 21

     
Hotplate Burners
The drawing by each knob indicates which burner that
knob controls.

This example shows the knobs for the middle and front
right burners.

There is a spark ignition system that works when the knob
is pressed in. Each burner also has a special safety device
that stops the flow of gas if the flame goes out.
Push in and turn a knob to the large flame symbol ( ).
Keep holding the knob pressed in to let the gas through
to the burner for few seconds. The igniter should spark
and light the gas.
If, when you let go of the control knob, the burner goes
out, the safety device has not held in. Turn the control to
the off position and wait one minute, then try again this
time holding in the control knob for slightly longer.

Adjust the flame height to suit by turning the knob.
On this hotplate the low position is beyond high, 
between high and off. The small flame marks the ‘low
position’. Turn the knob towards it after the contents of a
pan have boiled.
Make sure flames are under the pans. Using a lid will help
the contents boil more quickly.
Pans and kettles with concave bases or down turned base
rims should not be used.
Simmering aids, such as asbestos or mesh mats, are NOT
recommended. They will reduce burner performance and
could damage the pan supports.
Avoid using unstable and misshapen pans that may tilt
easily and pans with a very small base diameter e.g. milk
pans, single egg poachers. The minimum pan diameter
recommended is 120mm.
 - Griddle plates other than the Rangemaster
recommended item, should not be used, or damage to
the hob, supports or surround may occur.
The maximum pan base diameter is 260mm for the Centre
Wok burner and 220mm for the others.
The Wok burner is designed to provide even heat over
a large area. It is ideal for large pans and stir frying. For
heating smaller pans the smaller burners may be more
efficient.


If a burner flame goes out, turn the control knob off
and leave it for one minute before relighting it.
You can remove the burner parts for cleaning; see the
‘Cleaning your hotplate’ section of the instructions.
You should wipe the top surface of the hotplate
around the hotplate burners as soon as possible after
spills occur. Try to wipe them off while the enamel is
still warm.
Note:
Use of aluminium pans may cause metallic marking of
the pan supports. This does not affect the durability
of the enamel and may be cleaned off with a metal
cleaner such as 'Brasso'.
Warmer
Use the warmer for keeping food warm while the final
touches are put to a meal. To switch on the warmer,
turn the knob to clockwise or anti-clockwise . The
‘HOT’ indicator lights up. For best results, pre-heat a
covered serving dish for 10 minutes before adding
food to it.

 If the Warmer surface / control panel
glass shatters, due to accidental damage etc., isolate
the appliance from the electricity supply immediately
by turning it off at the wall and arrange for its repair.
DO NOT RECONNECT THE HOTPLATE TO THE ELECTRICITY
SUPPLY UNTIL AFTER REPAIR!

     
The Griddle (optional extra)
The griddle fits the centre right pan support, front to
back. It is designed for cooking food on directly. Don’t
use pans of any kind on it. The griddle surface is non-stick
and metal cooking utensils (e.g. spatulas) will damage the
surface. Use heat resistant plastic or wooden utensils.
Don’t put it crossways - it will not fit properly and will be
unstable.
Do not put it on the Wok burner or on the left hand side .
Position the griddle over the hotplate burners resting on
the pan support.
Check that it is securely located.
The griddle can be lightly brushed with cooking oil before
use. Light the hotplate burners. Adjust the flame heights
to suit.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn
the control knobs towards the low position, marked with
the small flame symbol, to reduce the burner flames
Always leave space around the griddle for the gases to
escape. Never fit two griddles side by side. Large pans
should also be spaced well apart.
Use the following heat settings as a guide for griddle
cooking.
High/medium:
Drop scones, Bacon, Chops, Steak, Burgers.
Medium/low:
Potato cakes, Eggs, Fish cakes.
Experience will soon familiarise you with the correct
setting to use for cooking.
After cooking allow the griddle to cool before
cleaning.
Don’t put it on a Wok burner - it is not designed to fit
the Wok burner pan supports.


The Wok cradle (optional extra)
The Wok cradle is designed to fit a Typhoon™ Professional
35cm Wok (Part Code 13840S)
This is available from leading retailers.
If you use a different Wok make sure that it fits the cradle.
Woks vary very widely in size and shape. It’s important
that the Wok sits down on the pan support - but if the
Wok is too small the cradle will not support it properly.
The cradle should be used on the triple ring Wok burner
only.
When you fit the cradle check that the Wok is properly
located on the front and rear fingers and that it is
supported properly on a pan support.
Make sure the cradle is stable and that the Wok is sitting
level in the ring.
The cradle will get very hot in use - allow plenty of time
for it to cool before you pick it up.

Essential information
Never use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
Recommended cleaning materials are hot soapy
water, a moistened soap pad, cream cleaner or a
nylon scourer.

     
Cleaning your hotplate
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity supply
before using the hotplate.







All parts of the hotplate can be cleaned with hot
soapy water - but take care that no surplus water
seeps into the appliance.

Some models have a separate trim ring, which fits on
the burner head.
The burner heads and caps can be removed for
cleaning. Make sure they are absolutely dry before
replacing.
The single ring burners
A cap, B head, C notch, D electrode, E base
When refitting the burner head, make sure that the
notch lines up with the electrode or hole in the base.
Check that the burner head is level and that the cap is
fitted centrally on the burner head.
The Wok burner
The Wok burner is a little more complicated but it also
can be taken apart for cleaning.
Wok burner
A inner burner cap, B outer burner cap
C inner burner head D outer burner head
E Wok burner base
When reassembling the Wok burner, turn over the
large base ring and find the ‘D’ shaped area.
Turn the head until the ‘D’ matches the one on the
burner base. Turn the head over and place it on the
burner base.
To fit the small inner burner, find the larger electrode
notch in the burner rim. Line this up with the white
ignition electrode and place the inner burner on the
large base ring.


A electrode notch B ignition electrode
Now fit the two burner caps, making sure that they
are sitting down properly.


Part Finish Recommended Cleaning Method
Hotplate Top Enamel or
Stainless Steel
Hot soapy water, soft cloth. Any stubborn stains remove
gently with a nylon scourer.
Pan Supports, Wok Cradle (some
models only)
Enamel coated
Cast Iron or
Stainless Steel
Cif Cream Cleaner- Faberge Lever and a nylon scourer.
Dishwasher.
Burner Caps Enamel Cream cleaner, nylon scourer. Dishwasher
Burner Trim Rings (some models
only) and Burner Head
Aluminium Cif or other cream cleaner with a soft cloth. Be careful not
to be over vigorous.
Griddle Plate (some models only) Non-Stick Surface Allow to cool. Wash in hot soapy water. Do not use
abrasive cleaners/scourers. Dishwasher.

Part Finish Recommended Cleaning Method
Control panel/Warmer Toughened Glass Damp soft cloth. Do not use abrasive cleaners on lettering.
Control Knobs Plastic/ Chrome Damp soft cloth.
Cleaners listed are available from Supermarkets or electrical retailers as stated. Cleaner manufacturer in Italics
For enamelled surfaces use a cleaner that is approved for use on vitreous enamel. The vitreous enamel association
has a list of approved cleaners. Contact them via their website www.ive.org.uk or telephone: [phone].
Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.

     
Troubleshooting
What cleaning materials are recommended for the
hotplate?
See the ‘Cleaning’ section for recommended cleaning
materials. We do not recommend Mr. Muscle, as it
contains chemicals that may damage the surfaces of
your hotplate.
If there is an installation problem and I don’t get my
original installer to come back to fix it who pays?
You do. Service organisations will charge for their call-
outs if they are correcting work carried out by your
original installer. It’s in your interest to track down
your original installer.
Power failure
In the event of a failure in the electrical supply the
hotplate may be lit using a match.
Hotplate ignition or hotplate burners faulty
Is the power on?
If so is there something wrong with the power
supply?
Are the sparker (ignition electrode) or burner slots
blocked by debris?
Is the burner trim correctly located?
Are the burner caps correctly located?
See the section entitled ‘Cleaning’
Hotplate burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.
Do the burners spark when you push the burner
control knob? If not check the power is on.
General Safety Instructions

The hotplate must be installed by a CORGI
registered engineer.

The installation must be carried out by a
Competent Person.
The installation must be in accordance with the
installation instructions and comply with the relevant
regulations and also the local gas and electricity
supply companies’ requirements.

Don’t turn electric switches on or off.
Don’t smoke
Don’t use naked flames
Do turn off the gas at the meter or cylinder
Do open doors and windows to get rid of the gas
Do keep people away from the area affected
Call your gas supplier.
If you are using natural gas in the UK ring Transco plc
on

This appliance is designed for domestic cooking
only. Use for any other purpose could invalidate
any warranty or liability claim.
The use of a gas cooking appliance results in the
production of heat and moisture in the room in
which it is installed. Ensure that the kitchen is well
ventilated: keep natural ventilation holes open or
install a mechanical ventilation device, (mechanical
extractor hood).
Prolonged intensive use of the appliance may call
for additional ventilation, for example opening a
window, or more effective ventilation, for example
increasing the level of mechanical ventilation where
present.
The hotplate should be serviced by a qualified service
engineer and only approved spare parts used. Have
the installer show you the location of the hotplate
control switch. Mark it for easy reference. Always
allow the hotplate to cool and then switch off at
the mains and before cleaning or carrying out any
maintenance work, unless specified otherwise in this
guide.
All parts of the hotplate become hot with use
and will retain heat even after you have stopped
cooking.
Take care when touching hotplate, to minimize
the possibility of burns, always be certain that the
controls are in the OFF position and that it is cool
before attempting to clean the hotplate.
Use dry oven gloves when applicable - using damp
gloves might result in steam burns when you touch
a hot surface. Never operate the hotplate with wet
hands.
Do not use a towel or other bulky cloth in place of
a glove. They might catch fire if they touch a hot
surface.

 
Clean with caution. If a wet sponge or cloth is used
to wipe spills on a hot surface, be careful to avoid
steam burns. Some cleansers can produce noxious
fumes if applied to a hot surface.
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
Babies, toddlers and young children should not be
allowed near the hotplate at any time. They should
never be allowed to sit or stand on any part of the
appliance. Teach them not to play with controls or
any other part of the hotplate.
Never store anything of interest to children in
cabinets above a hotplate - children climbing on the
hotplate to reach them could be seriously injured.
Clean only parts listed in this guide.
In the interests of hygiene and safety the hotplate
should be kept clean at all times as a build up in fats
and other food stuff could result in a fire.
Always keep combustible wall coverings or curtains
etc. a safe distance away from your hotplate.
Do not spray aerosols in the vicinity of the hotplate
while it is in on.
Do not store or use combustible materials, or
flammable liquids in the vicinity of this appliance.
Do not use water on grease fires. Never pick up a
flaming pan. Turn the controls off. Smother a flaming
pan on a surface unit by covering the pan completely
with a well fitting lid or baking tray. If available
use a multipurpose dry chemical or foam-type fire
extinguisher.
Never leave the hotplate unattended at high heat
settings. Pans boiling over can cause smoking and
greasy spills may catch on fire.
Never wear loose-fitting or hanging clothes while
using the appliance. Be careful when reaching for
items stored in cabinets over the hotplate. Flammable
material could be ignited if brought in contact with a
hot surface unit and may cause severe burns.
Take great care when heating fats and oils, as they
will ignite if they get too hot.
Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
Never leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If
you use a combination of oils or fats in frying, stir
them together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost
on frozen foods or moisture on fresh foods can cause
hot fat to bubble up and over the sides of the pan.
Carefully watch for spills or overheating of foods
when frying at high or medium high temperatures.
Never try to move a pan of hot fat, especially a deep
fat fryer. Wait until the fat is cool.
When using an electrical appliance near the hotplate,
be sure that the cord of the appliance does not come
into contact with the hotplate.
Take care that no water seeps into the appliance
Only certain types of glass, glass-ceramic,
earthenware or other glazed containers are
suitable for hotplate cooking; others may break
because of the sudden change in temperature.
Do not allow anyone to climb, stand or hang on any
part of the hotplate.
Make sure that your kitchen is well ventilated at all
times. Use extractor fans or hoods when fitted.
Never heat unopened food containers. Pressure build
up may make container burst and cause injury.
The hotplate is designed for cooking foods only
and must not be used for any other purpose.
The specification of this hotplate should not be
altered.
When the hotplate is not in use ensure that the
control knobs are in the off position.

     
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Installation

Before you start your installation, please complete the
details BELOW.
If your customer has a problem relating to your
installation they will be able to contact you easily.
Installer’s Name
Installer’s Company
Installer’s Telephone number


Prior to installation, ensure that the local distribution
conditions (nature of the gas and gas pressure) and the
adjustment of the appliance are compatible.
This appliance shall be installed in accordance with the
regulations in force and only in a well ventilated space.
Read the instructions before installing or using this
appliance.

The regulations and standards are as follows:-
In your own interest and that of safety, it is law that
all gas appliances be installed by competent persons.
CORGI registered installers undertake to work to
safe and satisfactory standards. Failure to install the
appliance correctly could invalidate any warranty or
liability claims and lead to prosecution. The hotplate
must be installed in accordance with
All relevant British Standards / Codes of Practice, in
particular BS 5440 Part 2 2000,
For Natural Gas - BS 6172 : 1990 and BS 6891 : 1998
For LP Gas - BS 5482-1:1994 (when the installation
is in a permanent dwelling). This appliance should
not be installed in a boat or caravan.
The Gas Safety (Installation and Use) regulations
1998.
The relevant Building / IEE regulations.
In the Republic of Ireland:-
The installation must be carried out by a Competent
Person and installed in accordance with the current
edition of I.S.813 “Domestic Gas Installations”, the
current Building Regulations and reference should
be made to the current ETCI rules for electrical
installation.

This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to
the relevant requirements regarding ventilation.
In the UK
The room containing the hotplate should have an air
supply in accordance with BS 5440 Part 2 : 2000. All
rooms require an openable window or equivalent,
while some rooms require a permanent vent in
addition to the openable window. The hotplate
should not be installed in a bedsitting room with
volume less than 20m3. If it is installed in a room
of volume less than 5m3 an air vent of effective
area 100cm2 is required; if it is installed in a room
of volume between 5m3 and 10m3, an air vent of
effective area 50cm2 is required; while if the volume
exceeds 11m3, no air vent is required.
If there are other fuel burning appliances in the same
room, BS 5440 Part 2 : 2000 should be consulted to
determine the requisite air vent requirements.
In the Republic of Ireland:-
Reference should be made to the current edition of
IS 813 which makes clear the conditions that must
be met to demonstrate that sufficient ventilation is
available.

The hotplate may be installed in a kitchen/kitchen diner
but NOT in a room containing a bath or shower.





All models are supplied set for use on group H natural gas.
A conversion kit for LP gas is included with the appliance.
See the instructions that are supplied with the conversion

 
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
kit. After converting the appliance please attach the Gas
Conversion sticker over the appropriate area of the data
badge, this will identify the gas type the appliance is now
set for.






GAS PRESSURE TESTER
FLEXIBLE GAS HOSE
Must be in accordance with
the relevant standards.
MULTIMETER
(for electrical checks)

1. Electric drill
2. Jig Saw
3. Steel tape measure
4. Cross head screwdriver
5. Flat head screwdriver
6. 4mm & 3mm Allen keys
7. Spirit level
8. Pencil
9. Adjustable spanner

3 pan supports









The hotplate should be fitted into a worksurface which
is at least 600mm deep. In position, it has a maximum
thickness of 50mm from the top of the work surface.
The cutout should be positioned centrally so that the
spaces at the front and rear are the same. The diagrams
below show the required cutout and the minimum
recommended distances from the hotplate to nearby
surfaces.
468mm
1150mm
600mm
minimum
cutout size
Above hotplate level a gap of 75mm should be left
between the left hand side of the hotplate and any
adjacent vertical surface.
For non-combustible surfaces (such as unpainted metal
or ceramic tiles) this can be reduced to 25mm.
A minimum space of 650mm is required between the
top of the hotplate and a horizontal combustible surface.
*Any hotplate hood should be installed in accordance
with the hood manufacturer’s instructions.
Surfaces of furniture and walls at the sides and rear of
the hotplate should be heat, splash and steam resistant.
Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage and discolouration.

     
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
We cannot accept responsibility for damage caused
by normal use of the hotplate to any material that de-
laminates or discolours at temperatures less than 65°C
above room temperature.
For safety reasons curtains must not be fitted
immediately behind the hotplate.
NOTE When the Freestyle ovens are situated under the
hob, additional brackets should be fixed to the rear wall
to support the rear edge of the worktop. Two right-angle
brackets are supplied for this purpose. Alternatively, a
wooden baton could be fixed to the wall under the rear
edge.
The front edge will be supported by the ovens once they
are in place. It is important that the hob is placed directly
above the ovens to ensure this. See diagram.
Hob
Oven front
top supports
the Hob Freestyle Ovens
worktop
Wall
Bracket at rear
fixed to wall

The hotplate is heavy. Take great care.
We recommend two people manoeuvre the hotplate.

If the appliance is to be converted to LP gas do the
conversion at this point. See the conversion section of
these instructions.

Before connecting the appliance, check that it is suitable
for your gas and electricity supply. This information is on
the data label fixed to the underside of the hotplate. Gas
connection must comply with the relevant standards
and regulations in force.
The gas connection point is located as shown in the
diagram opposite. The inlet union is Rp 1/2 .
The appliance must be connected to the gas supply
system with one of the following:

The joints of this pipe must consist of threaded fittings
conforming to the standards. Use of seals such as hemp
with suitable cement, or Teflon tape, is permitted.

The joints of this pipe must consist of unions with
mechanical seals.

A hose is not supplied by with the hotplate. Hoses may
be purchased at most builders’ merchants.
The hose should be fitted so that both inlet and
outlet connections are vertical so that the hose hangs
downwards.
The hose must be in accordance with the relevant
standards. In the UK these are:-
For Natural Gas the flexible hose must be in
accordance with B.S.669.
gas connection union
underside of hotplate showing the fixing clips

 
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
For LP Gas it should be capable of 50mbar pressure,
70°C temperature rise and carry a red stripe, band or
label.

Ensure that the gas supply pipe is never able to touch
moveable parts of the built-in cabinet (e.g. drawers). It
must not pass through compartments that could be used
for storage purposes. When using a flexible hose, it is
essential to comply with the following instructions:
- No part of the pipe must be able to touch parts the
temperature of which exceeds 75°C
- The pipe must not be pulled or twisted, throttled or
tightly bent.
- It must not come into contact with sharp edges or
corners.
- It must be easy to inspect the entire pipe length in
order to check its state of wear.
- The pipe must be replaced within the date stamped
on the pipe itself.
If in doubt contact, your supplier.
After completing the gas connection, check the hotplate
is gas sound with a pressure test.

The gas pressure can be measured at one of the centre
hotplate burner injectors (not the Wok burner). Lift off a
burner head. Fit the pressure gauge to the injector. Turn
on and light one of the other hotplate burners. Turn on
and push in the control knob for the burner with the
pressure gauge fitted to let gas through.
Pressures
 
20mbar. Butane 29mbar
Propane 37mbar
Turn off the burners. Reassemble burner top, making
sure it is reassembled in the correct way on the burner
body.

The hotplate must be sealed to the work surface to
prevent liquid from infiltrating into the cabinet. A foam
tape seal is supplied with the hotplate. Carefully follow
these instructions in order to correctly apply this seal:
Turn the hotplate over and place in on a secure level
surface. Detach the foam seal from the backing, checking
that the transparent protection still adheres to the
seal itself. Position seal carefully along the edge of the
hotplate. Take special care in the corners making sure
there are no gaps. The ends of the strips must fit together
without overlapping.
under side of the hotplate showning the foam seal
If the surface that the hotplate is to be fitted to is tiled,
or is not reasonably smooth, additional sealing with a
waterproof silicone sealant may be required.
Turn the hotplate back the right way up and fix it to the
worktop with the brackets.
Ensure the tag fits into the slot on the hotplate base, then
tighten the screw until it is locked to the worktop.

This appliance must be installed by a qualified electrician
to comply with the relevant Institute of Electrical
Engineers (I.E.E.) regulations and also the local electricity
supply company requirements.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
All external wiring must comply with the IEE Regulations
for the Electrical Equipment of Buildings. Connection to
the electrical supply can be made with either a plug and
socket or be permanently wired via a double pole switch.
The cooker is supplied with a 3 core cable 2m long.

     
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
If a replacement cable is fitted it must be 250v high
temperature rubber/synthetic of 0.75mm2 minimum
conductor size. Connect the replacement cable to the
terminal block on the hotplate as shown.

For a plug connection a three pin plug to BS1363 with
a capacity of not less than 13 ampere must be used and
fitted with a 3 ampere fuse ‘ASTA’ approved to BS 1362.
After replacing the fuse the cover must be refitted.
If the cover is lost, the plug must not be used until a
replacement cover has been obtained from your supplier.
The colour of the correct fuse carrier is that of the
coloured insert in the base of the fuse recess, or stated
elsewhere on the plug. Always state this colour when
ordering a replacement fuse carrier.
IMPORTANT The wires in the mains lead are coloured in
accordance with the following code:-
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
The wires should be connected into the terminal of your
plug as shown:
Electrical checks

The hotplate must be disconnected from the power
supply. Set your meter to (ohm) on the X1 scale and
adjust to zero if necessary.
Test the leads from the earth connection on the hotplate
terminal, to the earth pin on the hotplate plug. The
resistance should be less than 1 (ohm). If it is not, check
all the earth wires for continuity. Check that all contacts
are clean and tight. Re-check. If the resistance is still
greater than 1 (ohm) there may be a problem, consult a
qualified electrical engineer.
POLARITY CHECK
The hotplate must be connected to the power supply.
Your meter should be set on 300V ac scale.
Test at the hotplate terminal block:
1. Test leads from L to N. Your meter should read
approx. 220-240V ac.
2. Test leads from L to E. Your meter should read
approx. 220-240V ac.
3. Test leads from N to E. Your meter should read
approx. 0-15V ac.
If the readings are different from these values there is
an electrical fault. Rectify any fault and repeat the test. If
necessary repeat the test at the supply system socket/spur
- if the fault also occurs at this stage then there is a house
system fault which requires attention by the Electrical
Authority.
The customer should be warned NOT to use the appliance
until this examination has been carried out.

Check each burner in turn. There is a spark ignition system
that works when the knob is pressed in. Each burner also
has a special safety device that stops the flow of gas if the
flame goes out.
Push in and turn a knob to the large flame symbol ( ).
Keep holding the knob pressed in to let the gas through
to the burner for few seconds. The igniter should spark
and light the gas.
If, when you let go of the control knob, the burner goes
out, the safety device has not held in. Turn the control to
the off position and wait one minute, then try again this
time holding in the control knob for slightly longer.

Please complete your contact details in the front of
this section. Please inform the user how to operate the
hotplate and hand over the instruction pack.


 


Conversion to LP gas




This conversion must be performed by a competent
person. After conversion the installation must comply
with the relevant regulations and also the local
electricity supply company requirements. Read the
instructions before converting this appliance.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and lead to
prosecution.
This instruction must be used in conjunction with
the rest of the appliance instruction, in particular
for information on Standards, hotplate positioning,
connection hose suitability etc.
When servicing or replacing gas-carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion.
Do not use re-conditioned or unauthorised gas controls.


Before electrical re-connection, check that the appliance
is electrically safe.

Remove burner caps and heads. Remove old jets. Fit the
new jets (see Technical Data section at the back of the
book for correct jets). Reassemble in reverse order.

Disconnect from electricity supply.
Pull off all the control knobs and remove the two
hexagon headed screws (which act as locators for the
pan support), from the edge of the hotplate under the
right hand pan support.
Slide the glass to the rightslightly and lift it from the
side. Carefully lift it clear of the hotplate and place the
panel somewhere safe. The tap bypass screws are now
accessible once the bezel location brackets are removed.
Turn the bypass screw on each control clockwise to the
stop.
Refit the glass panel and replace the fixing screws in the
top edge of the hotplate.
Carefully replace the control sealing rings and replace
the control knobs.

     



Stick the LP gas label over the natural gas part of the
appliance data label.

Connect the appliance to the gas supply. Check the
appliance is gas sound.
The gas pressure can be measured at one of the left
hand hotplate burner jets. Lift off a burner head. Fit the
pressure gauge to the jet. Turn on and light one of the
other burners with a match. Turn on and press in the
control knob for the burner with the pressure guage
fitted.
The pressure should be 29mbar for Butane and 37mbar
for Propane. After checking the pressure, turn the taps
off and replace the burner head.
Reassemble burner top, making sure it is reassembled in
the correct way on the burner body.



 



     
Circuit Diagram
L N
L
N
Warmer Switch
Warmer Element
Mains Terminal Block
Spark Generator
Ignition Swirches
or
bk
b
y
b
w
w
bk
bk
Warmer Neon
bk
D
C1
A
B
C2
C3
Connection shown in circuit diagram is for single phase. Ratings are for 230V 50Hz
Code Item
A Ignition generator
B Ignition switches
C1 Warmer switch
C2 Warmer neon
C3 Warmer
D Mains terminal
Code Colour
b Blue
bk Black
or Orange
w White
y Yellow