Range Master CRUB3314WH User manual

U110801-02
RUSTIQUE CERAMIC
UNDERMOUNT SINK
CERAMIC INSET SINK

1
 IMPORTANT!
• If you are mounting your sink into a granite or marble
worktop you must have a fabricator cut the hole for you.
• Due to dimensional tolerances within all ceramic sinks
these instructions should be used as guidelines only.
• The position of your sink will be determined by the
relationship of the sink edges to cabinet gables,
supports and tap location.
• Ensure current plumbing fixtures are long enough to
reach the new sink and it’s location.
• If unsure of fitting your sink we recommend seeking
the advice of a professional fitter. Rangemaster will
not accept responsibility for errors in countertop
preparation or installation.
Preparation
1. Take great care when handling this sink, whilst every
eort has been taken to remove sharp edges, the
material by nature may be sharp. We recommend
wearing gloves accordingly. DO NOT lift the product
by the waste hole(s) or tap hole(s). We recommend 2
people should be used to handle this product.
2. Check the package for completeness, possible
defects or any transport damage before installation
commences. Installed faulty product will not be
honoured by the warranty.
3. Check that the supporting carcass and worktop is level
left to right and front to back to ensure correct drainage
of water.
4. Check that the surrounding furniture is the correct size
and shape to accept this product and that no plumbing
or wiring may foul the installation.
5. If replacing an existing sink, remove this product and
clean the surrounding area, ensure the new sink will suit
the existing cut out size and position, otherwise amend
the cut out size accordingly.
6. Before creating the cut out in the worktop, carefully
plan the positioning of the sink. Ensure that the position
of the bowl(s), tap and overows will not interfere with
surrounding units or appliances. Check that the xing
clips will not foul carcass walls or supporting braces.
7. Carefully mark out the cut out using the provided
technical drawing or template for either the
undermount installation or inset installation. Create the
sink cut out in the worktop using a router or CNC cutter,
follow the manufacturer’s instructions taking care not to
chip, crack or scratch the worktop. If preparing the cut
out in situ cover any open pipework to avoid any debris
contaminating the water supply feeds.
8. All ceramic products should be supported under the
reverse face with a substantial braced shelf similar (Fig.
1.2). The shelf should be designed to allow for small
adjustments in height at each corner and so that it
could be disassembled from the underside in the event
that the sink is accidentally damaged.
a. b.
d.
c.
e.
b.
c.
a.
Key Description
a. Surrounding cupboards or end panels
b. Hole for waste connections (min recommended dia. 150mm for
each waste, centred to waste)
c. Supporting shelf (moisture resistant timber or similar, ensure
framework sits directly under the product)
d. Incoming hot and cold supply pipes
e. Supporting uprights (front & back)
Fig. 1.1
Fig. 1.2
Parts and Contents
Key Description Qty
a. Sink (may dier from model
shown)
1
b. Overow pipework 1
c. Care instructions and or template 1
n/a. Basket strainer waste(s) dependant on model
n/a Connecting pipework dependant on model
You will need:
Electric saw with jigsaw tment or a router
Translucent silicone sealant

2
Undermount sink
CRUB3314WH/ (Fig. 1.3)
CRUB3216WH/ (Fig. 1.4)
CRUB4040WH/ (Fig. 1.5)
CRUB5340WH/ (Fig. 1.6)
CRUB385WH/ (Fig. 1.7)
CRUB1740WH/ (Fig. 1.8)
• To ensure perfect positioning of the product, the cutout
details are shown below. The cutout template is also
available online www.rangemaster.co.uk.
• The height of the shelf should be such that when the
sink is placed on the shelf the top face rim of the sink is
level with the underside face of the worktop, see (Fig.
1.9) and (Fig. 1.10).
Installation
IMPORTANT: Due to the larger dimensional tolerances on
ceramic products we strongly recommend making the cut
out in a scrap piece of material then checking it against the
actual sink to be tted. The cut out size should be adjusted
to suit the sink tolerances and retested against the intended
product before committing to cutting the nal worksurface.
The ‘nominal’suggested cut out size will align the cut out
edge with the bowl edge radius. The oset from the bowl can
be adjusted to overhang or be set back according to personal
taste but, this may interfere with installation or the correct
usage of sink accessories.
Note: If the cut out is adjusted to either overhang or set back
from the sink rim, sucient surface area must be left to allow
a water tight seal. Fig. 1.10 shows the cut out ush to the
bowl radius.
Please do not over tighten any ttings as this may cause the
surface of your ceramic sink to crack.
1. Install the tap to the worktop according to the
manufacturer’s instructions. Ensure the tap is secure as
later access may be obstructed by the sink or plumbing.
We recommend using long exible tap connectors to
help.
2. Install the basket strainer waste kit(s) and overow
according to the manufacturer’s instructions.
3. Clean the cut out perimeter of the worktop underside
and the upper perimeter of the sink with a degreasing
cleaning solvent and allow to dry.
4. Apply a continuous generous bead of good quality
silicone onto the rim around the upper perimeter of the
sink (Fig. 1.9) or (Fig. 1.18).
5. Gently lay the worksurface onto the sink, carefully align
the sink rim with the cut out shape with equal spacing
on all sides (Fig. 1.10).
Where possible apply a 2nd and 3rd bead of silicone around
inside and outside of the adjoining sink and worktop. Any
excess silicone can be cleaned away using a proprietary
silicone cleaner. Allow the silicone to dry.
6. Attach the sink connecting pipework to the waste kit(s)
according to the manufacturer’s instructions.

3
525
450
R10
R10
350
290
390
390
R10
532
392
R10
390
525
R10
Undermount sink cutout
Fig. 1.3
Fig. 1.5
Fig. 1.6
Fig. 1.4
CRUB3314WH/
CRUB4040WH/
CRUB5340WH/
CRUB3216WH/
ø375
390
164
R10
Fig. 1.7
Fig. 1.8
CRUB385WH/
CRUB1740WH/
Fig. 1.9 Fig. 1.10

4
Inset sink
CRUB3314WH/ (Fig. 1.11)
CRUB3216WH/ (Fig. 1.12)
CRUB4040WH/ (Fig. 1.13)
CRUB5340WH/ (Fig. 1.14)
CRUB385WH/ (Fig. 1.15)
CRUB1740WH/ (Fig. 1.16)
• The cut out details are shown in (Fig. 1.11) or (Fig. 1.12)
ensure perfect positioning of this product. The cutout
template is also available online www.rangemaster.
co.uk.
• When installing as an Inset Sink, a chamfer in the
underside of the worktop may be required for the
overflow body (Fig. 1.17).
Applying the Silicon sealant
• Apply silicone sealant (not supplied) to the underside of
the sink rim (Fig. 1.18).
• Turn the sink over and feed into pre-prepared cut-out
(Fig. 1.19).
• Remove any surplus sealing material or wipe away any
excess sealant.