Ransomes 51 Super Certes Guide

®
RJL 100 February 2011
GB
United
Kingdom
Iceland
IS
Safety, Operation & Maintenance Manual
Öryggis-, notkunar- og viðhaldshandbók
Ransomes Super Certes 51 & 61, Super Bowl 51 and
Marquis 51 & 61 Walkbehind Reel Mowers
RansomesSuperCertes51&61,Super Bowl 51
og Marquis 51 & 61 sláttuvélar
Super Certes 51 Series: EC3 Product Code: LDFC500 Engine type: Honda GX120-QX9
Super Certes 61 Series: JG Product Code: LDFC600 Engine type: Honda GX120-QX9
Super Bowl 51 Series: JF Product Code: LDFD500 Engine type: Honda GX120-QX9
Marquis 51 Series: EF3 Product Code: LDAA500 Engine type: Honda GX120-QX9
Marquis 61 Series: EG3 Product Code: LDCB600 Engine type: Honda GX120-QX9
Super Certes 51 Flokkur: EC3 Framleiðslunúmer: LDFC500 Tegund vélar: Honda GX120-QX9
Super Certes 61 Flokkur: JG Framleiðslunúmer: LDFC600 Tegund vélar: Honda GX120-QX9
Super Bowl 51 Flokkur: JF Framleiðslunúmer: LDFC500 Tegund vélar: Honda GX120-QX9
Marquis 51 Flokkur: EF3 Framleiðslunúmer: LDAA500 Tegund vélar: Honda GX120-QX9
Marquis 61 Flokkur: EG3 Framleiðslunúmer: LDCB600 Tegund vélar: Honda GX120-QX9
WARNING
WARNING: If incorrectly used this machine can cause severe
injury. Those who use and maintain this machine should be
trained in its proper use, warned of its dangers and should
read the entire manual before attempting to set up, operate,
adjust or service the machine.
VIÐVÖRUN
VIÐVÖRUN: Röng notkun á vélinni getur valdið alvarlegum
meiðslum. Þeir sem nota og sjá um viðhald á þessari vél ættu
að hljóta þjálfun í réttri notkun hennar, fá vitneskju um
hætturnar og ættu að lesa alla handbókina áður en þeir reyna
að setja upp, nota, aðlaga eða þjónusta vélina.
25018G-IS (rev.0)

©2011, Ransomes Jacobsen Limited. All Rights Reserved / Öll réttindi áskilin
Ransomes Jacobsen Limited reserves the right to make design changes without obligation to make these
changes on units previously sold and the information contained in this manual is subject to change without notice.
Ransomes Jacobsen Limited áskilur sér rétt til að gera breytingar á hönnun án þess vera skuldbundið til að gera
þessar breytingar á þegar seldum tækjum og upplýsingarnar í þessari handbók geta breyst án fyrirvara.

en-3
1 CONTENTS
2 INTRODUCTION
2.1 IMPORTANT ................................................................4
2.2 PRODUCT IDENTIFICATION ......................................5
2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP
PRODUCTS .................................................................6
2.3.1 DURING SERVICE LIFE ..............................................6
2.3.2 END OF SERVICE LIFE ..............................................6
2.4 PARTS MANUAL .........................................................7
2.5 KEY NUMBERS............................................................7
3SAFETY
3.1 OPERATING SAFETY .................................................8
3.1.1 OPERATING INSTRUCTIONS ....................................8
3.1.2 SAFETY SIGNS ...........................................................8
3.1.3 STARTING THE ENGINE ............................................8
3.1.4 DRIVING THE MACHINE ............................................8
3.1.5 TRANSPORTING .........................................................9
3.1.6 LEAVING THE DRIVING POSITION ...........................9
3.1.7 SLOPES .......................................................................9
3.1.8 BLOCKED CUTTING UNITS .......................................9
3.1.9 ADJUSTMENTS, LUBRICATION,
MAINTENANCE & CLEANING ...................................10
4 SPECIFICATIONS
4.1 MACHINE SPECIFICATION .......................................12
4.2 DIMENSIONS & WEIGHTS ........................................12
4.3 ENGINE SPECIFICATION ..........................................14
4.4 SLOPES ......................................................................14
4.5 RECOMMENDED LUBRICANTS ...............................14
4.6 VIBRATION LEVEL .....................................................15
4.7 CERTIFICATES OF CONFORMITY ...........................16
5 DECALS
5.1 SAFETY DECALS EC .................................................30
5.2 INSTRUCTION DECALS EC ......................................30
6 CONTROLS
6.1 OPERATOR PRESENCE CONTROL -
MECHANICAL (OPC) ................................................31
6.2 LANDROLL CLUTCH ..................................................31
6.3 THROTTLE CONTROL ...............................................31
6.4 BRAKE RELEASE LEVER ..........................................32
6.5 CYLINDER CLUTCH LEVER ......................................32
6.6 IGNITION CUT-OUT SWITCH ....................................32
7 OPERATION
7.1 DAILY INSPECTION ...................................................33
7.2 OPERATOR PRESENCE AND SAFETY
INTERLOCK SYSTEM ................................................34
7.3 OPERATING PROCEDURE .......................................35
7.4 OPERATION OF THE MACHINE ...............................36
8 ADJUSTMENTS
8.1 51 MARQUIS: HEIGHT OF CUT ADJUSTMENT .......38
8.2 61 MARQUIS: HEIGHT OF CUT ADJUSTMENT .......38
8.3 MARQUIS: ALIGNING THE FRONT ROLLS ..............39
8.4 SUPER CERTES: HEIGHT OF CUT ADJUSTMENT .39
8.5 CYLINDER TO BOTTOM BLADE ADJUSTMENT ......40
8.6 CYLINDER CLUTCH ADJUSTMENT ..........................40
8.7 CONCAVE ADJUSTMENT .........................................41
8.8 LANDROLL SCRAPER ...............................................41
8.9 LANDROLL CLUTCH ADJUSTMENTS ......................42
8.10 CHAIN ADJUSTMENTS .............................................42
8.11 BACKLAPPING ...........................................................43
8.12 HANDLE ADJUSTMENT ............................................44
8.13 MARQUIS: SIDE ROLLS ............................................44
8.14 MAIN CLUTCH ADJUSTMENT ...................................45
8.15 PARKING BRAKE ADJUSTMENT ..............................45
9 ACCESSORIES
9.1 BRUSH AND COMB SET ...........................................46
9.2 TRANSPORT WHEELS (SUPER CERTES ONLY) ....46
9.3 TRAILING SEAT .........................................................47
9.4 VERTI-GROOM ATTACHMENT..................................47
9.5 VERTI-GROOM DRIVE BELT..................................... 48
9.6 VERTI-GROOM LUBRICATION .................................49
10 MAINTENANCE
MAINTENANCE AND LUBRICATION CHART ...........50
10.1 ENGINE DAILY (EVERY 8 WORKING HOURS) ........51
10.2 ENGINE WEEKLY: (EVERY 50 WORKING HOURS) 52
10.3 CLUTCH AND LAYSHAFT COVER ............................52
11 LUBRICATION
11.1 ENGINE DAILY: (EVERY 8 WORKING HOURS) .......53
11.2 ENGINE: (AFTER FIRST 20 HOURS) ........................53
11.3 ENGINE WEEKLY: (EVERY 50 WORKING HOURS) 53
11.4 MACHINE ....................................................................54
12 GUARANTEE / SALES & SERVICE
12.1 GUARANTEE / SALES & SERVICE ...........................55

en-4
2 INTRODUCTION
2.1 IMPORTANT ____________________________________________________
The Ransomes Super Certes, Super Bowl & Marquis are gasoline powered walk behind reel mowers. Using
chain drives for traction drive and cutting reel drives.
IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is operated
and maintained.
This SAFETY AND OPERATORS MANUAL should be regarded as part of the machine. Suppliers of both
new and second-hand machines are advised to retain documentary evidence that this manual was provided
with the machine.
This machine is designed solely for use as a grass cutting machine operating within the parameters listed in
the specification pages. Use in any other way is considered as contrary to the intended use. Compliance
with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer,
also constitute essential elements of the intended use.
Before attempting to operate this machine, ALL operators MUST read through this manual and make
themselves thoroughly conversant with Safety Instructions, controls, lubrication and maintenance.
Accident prevention regulations, all other generally recognized regulations on safety and occupational
medicine, and all road traffic regulations shall be observed at all times.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability for any
resulting damage or injury.
It is important that during the life of the machine wearing and replaceable parts are disposed of in an
environmentally responsible way using the resources available in the country where it is used. There are
guidelines in this manual for the eventual decommissioning of the mower once it has no further use.
Use only Ransomes Jacobsen Genuine spare parts to ensure the control of EC compliance 2006/42/EC.
These are the Original instructions verified by Ransomes Jacobsen Limited.

en-5
2 INTRODUCTION
2.2 PRODUCT IDENTIFICATION _______________________________________
A Maximum front axle load in Kg (for machines being
driven on the highway)
B Gross weight (mass) in Kg
C MaximumrearaxleloadinKg(formachinesbeingdriven
on the highway)
D Power in Kw
E Date code
F Machine type (Designation)
G Product code
H Product name
J Serial number
SERIAL PLATE LOCATION
The serial plate is located on the right hand side
plate of the main frame.
Kg Kw Kg Kg
West Road
Ransomes Europark
Ipswich IP3 9TT
England
ABCD E
FG
HJ
AKg Kw
Kg Kg
WestRoad
Ransomes Europark
Ipswich IP3 9TT
England
AC

en-6
2 INTRODUCTION
2.3 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _____________
2.3.1 DURING SERVICE LIFE
Used oil, oil filters and engine coolant are hazardous materials and should be handled in a safe and
environmentally responsible way.
In the event of a fluid leak, contain the spill to prevent it entering the ground or drainage system. Local
legislation will dictate how such spills are to treated.
Following the maintenance procedures laid out in this manual will ensure that the impact the machine has on
the local environment is controlled.
When it has been identified that a turf care product has no further functional value and requires disposal, the
following actions should be taken.
2.3.2 END OF SERVICE LIFE
These guidelines should be used in conjunction with applicable Health, Safety and Environmental legislation
and use of approved local facilities for waste disposal and recycling.
• Position the machine in a suitable location for any necessary lifting equipment to be used.
• Use appropriate tools and Personal Protective Equipment (PPE) and take guidance from the
technical manuals applicable to the machine.
• Remove and store appropriately:
1. Batteries
2. Fuel residue
3. Engine coolant
4. Oils
• Disassemble the structure of the machine referring to the technical manuals where appropriate.
Special attention should be made for dealing with ‘stored energy’ within pressurised elements of the
machine or tensioned springs.
• Any items that still have a useful service life as second hand components or can be re-serviced
should be separated and returned to the relevant centre.
• Other worn out items should be separated into material groups for recycling and disposal consistent
with available facilities. More common separation types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
•Plastics •Identifiable
• Recyclable
• Non recyclable
• Not identified
• Rubber
• Electrical & Electronic Components
• Items that cannot be separated economically into different material groups should be added to the
‘General waste’ area.
• Do not incinerate waste.
Finally update machinery records to indicate that the machine has been taken out of service and scrapped.
Provide this serial number to Ransomes Jacobsen Warranty department to close off relevant records.

en-7
2 INTRODUCTION
2.4 PARTS MANUAL ________________________________________________
As part of the ISO14001 principles and in the era of free electronic media, Ransomes Jacobsen Limited no
longer sends a paper parts manual with every product.
If you wish to refer to a parts list for this mower you have four options from which to choose:
Website – www.ransomesjacobsen.com then use the “GENUINE PARTS” tab then the “online parts look-up”
tab. This will give you live access to Parts drawings and lists to aid the identification of spare parts.
Website – www.ransomesjacobsen.com then use the “CUSTOMER CARE” tab followed by the “manuals” tab
this will give you access to a printable version of the parts manual. It can be saved to your computer drive for
reference on the screen or to print all or part of the book as required.
Alternatively by completing the form included in the technical manual pack supplied with the machine, we can
send you either:
• A CD containing an electronic copy of the Parts Book.
• A paper copy of the parts manual.
2.5 KEY NUMBERS ________________________________________________
It is recommended that all key numbers are noted here:
Starter Switch:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
It is also recommended that the machine and engine numbers are recorded.
The machine serial number is located on the registration plate and the engine serial number can be found on
the rocker cover.
Machine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Engine Number:- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

en-8
3 SAFETY INSTRUCTIONS
3.1 OPERATING SAFETY ____________________________________________
This safety symbol indicates important safety messages in this manual. When you see this symbol, be alert
to the possibility of injury, carefully read the message that follows, and inform other operators.
3.1.1 OPERATING INSTRUCTIONS
• Ensure that the instructions in this book are read and fully understood.
• No person should be allowed to operate this machine unless they are fully acquainted with all the
controls and the safety procedures.
• Never allow children or people unfamiliar with these instructions to use this machine. Local regulations
may restrict the age of the operator.
3.1.2 SAFETY SIGNS
• It is essential all safety labels are kept legible, if they are missing or illegible they must be replaced. If
any part of the machine is replaced and it originally carried a safety label, a new label must be affixed
to the replacement part. New safety labels are obtainable from Ransomes Jacobsen dealers.
3.1.3 STARTING THE ENGINE
• Before starting the engine check that the brakes are applied, drives are in neutral, guards are in
position and intact, and bystanders are clear of the machine.
• Do not run the engine in a building without adequate ventilation.
3.1.4 DRIVING THE MACHINE
• Before moving the machine, check to ensure that all parts are in good working order, paying particular
attention to brakes, tyres, steering and the security of cutting blades.
• Replace faulty silencers, mow only in daylight or good artificial light
• Always observe the Highway Code both on and off the roads. Keep alert and aware at all times. Watch
out for traffic when crossing or near roadways.
• Stop the blades rotating before crossing surfaces other than grass.
• Remember that some people are deaf or blind and that children and animals can be unpredictable.
• Keep travelling speeds low enough for an emergency stop to be effective and safe at all times, in any
conditions.
• Remove or avoid obstructions in the area to be cut, thus reducing the possibility of injury to yourself
and/or bystanders.
• When reversing, take special care to ensure that the area behind is clear of obstructions and/or
bystanders. DO NOT carry passengers.
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people
or their property.

en-9
3 SAFETY INSTRUCTIONS
• When the machine is to be parked, stored or left unattended, lower the cutting units or apply the
transport latches.
• While mowing, always wear substantial footwear and long trousers. Do not operate the equipment
when barefoot or wearing open sandals.
• After striking a foreign object Inspect the lawnmower for damage and make repairs before restarting
and operating the equipment.
• If the machine starts to vibrate abnormally, check immediately.
3.1.5 TRANSPORTING
• Ensure that the cutting units are securely fastened in the transport position. Do not transport with
cutting mechanism rotating.
• Drive the machine with due consideration of road and surface conditions, inclines and local
undulations.
• Sudden decelerating or braking can cause the rear wheels to lift.
• Remember that the stability of the rear of the machine is reduced as the fuel is used.
3.1.6 LEAVING THE DRIVING POSITION
• Park the machine on level ground.
• Before leaving the driving position, stop the engine and make sure all moving parts are stationary.
Apply brakes and disengage all drives. Remove the starter key.
3.1.7 SLOPES
TAKE EXTRA CARE WHEN WORKING ON SLOPES
• Local undulations and sinkage will change the general slope. Avoid ground conditions which can cause
the machine to slide.
• Keep machine speeds low on slopes and during tight turns.
• Sudden decelerating or braking can cause the rear wheels to lift. Remember there is no such thing as
a “safe” slope.
• Travel on grass slopes requires particular care.
IMPORTANT: When working on any slope select weight transfer, Adjust to provide adequate traction.
3.1.8 BLOCKED CUTTING UNITS
• Stop the engine and make sure all moving parts are stationary.
• Apply brakes and disengage all drives.
• Release blockages with care. Keep all parts of the body away from the cutting edge. Beware of energy
in the drive which can cause rotation when the blockage is released.
• Keep other people away from the cutting units as rotation of one can cause the others to rotate.

en-10
3 SAFETY INSTRUCTIONS
3.1.9 ADJUSTMENTS, LUBRICATION, MAINTENANCE & CLEANING __________
• Stop the engine and make sure all moving parts are stationary.
• Apply brakes and disengage all drives.
• Read all the appropriate servicing instructions.
• Use only the replacement parts supplied by the original manufacturer.
• When adjusting the cutter blades take care not to get hands and feet trapped when rotating blades.
• Make sure that other people are not touching any cutting unit, as rotation of one blade can cause the
others to rotate.
• To reduce the fire hazard, keep the engine, silencer and battery compartments free of grass, leaves or
excessive grease.
• Replace worn or damaged parts for safety.
• When working underneath lifted parts or machines, make sure adequate support Is provided.
• Do not dismantle the machine without releasing or restraining forces which can cause parts to move
suddenly.
• Do not alter engine speed above maximum quoted in Engine Specification. Do not change the engine
governor settings or overspeed the engine. Operating the engine at excessive speed may increase
the hazard of personal injury.
• When refuelling, STOP THE ENGINE, DO NOT SMOKE. Add fuel before starting the engine, never
add fuel while the engine is running.
• Use a funnel when pouring fuel from a can into the tank.
• Do not fill the fuel tank beyond the bottom of the filler neck.
• Replace all fuel tank and container caps securely.
• Store fuel in containers specifically designed for this purpose.
• Refuel outdoors only and do not smoke while refuelling.
• If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage
and avoid creating any source of ignition until fuel vapours have dissipated.
• Allow the engine to cool before storing in any enclosure.
• Never store the equipment with fuel in the tank inside a building where fumes may reach an open
flame or spark.
• If the fuel tank has to be drained, this should be done outdoors.
• Do not spill fuel onto hot components.
• When servicing batteries, DO NOT SMOKE, and keep naked lights away.
• Do not place any metal objects across the terminals.
• When Pressure Washing the Mower. Turn the engine off and remove the starter key.
If the engine has been running, it should be allowed to cool sufficiently to prevent damage to the block
and exhaust manifold. Never force water into any electrical components, the air cleaner or exhaust
muffler as water could enter the engine cylinder and cause damage.
DANGER:
Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury and
property damage. It may also be used to alert against unsafe practices.