RAPIX DGOZ-LRS-PRLLSW User manual

RAPIX Xi DALI Long Range Occupancy Sensor DGOZ-LRS-PRLLSW
Page 1 of 4
DGOZ-LRS-PRLLSW - RAPIX Xi DALI Long Range Occupancy Sensor
With Auxiliary Input
Product summary and capabilities
The Long Range Occupancy Sensor acts as a motion / occupancy sensor and DALI
Application Controller. The advanced control functions can be used in any DALI or
DALI-2 system.
The sensor is commissioned using the RAPIX Addressing or RAPIX Integrator
software. These software packages are available at no charge from ozuno.com.
Important notes and safety information
WARNING –Electric shock may result in serious injury or death.
Follow all warnings in this guide and on the product. Work in
accordance with the latest electrical safety practices.
•This Occupancy Sensor is powered only from DALI line.
•DALI system wiring is only single insulated from mains. Treat DALI wiring the same as mains wiring.
•The Auxiliary input wiring has no isolation from DALI. Treat the Auxiliary input the same as mains wiring.
•The Auxiliary input does not provide any power source. Connect it only to voltage-free contacts or a switch. Do
not connect any part of the Auxiliary Input to any other power source, or to earth, or to mains line or neutral.
•There are no user serviceable parts inside the Occupancy Sensor. Do not attempt to disassemble or operate the
device with any covers removed.
•This sensor is intended for indoor use only.
Indicators
DALI Activity: A DALI activity indicator is located near the terminal block. This blinks green and can be seen
through the plastic housing.
During installation and before pushing into the ceiling hole: If a green glow can be seen with a
blink about every 1 .. 2 seconds, then DALI is connected and the device has electrical power.
Discovery: The RAPIX commissiong software includes a discovery function. When activated, an indicator
under the PIR lens will flash. This allows physical location of the sensor after it has been
installed.
Terminals

RAPIX Xi DALI Long Range Occupancy Sensor DGOZ-LRS-PRLLSW
Page 2 of 4
Specifications
Sensor
Detection range (radius)
Up to 12 metres, dependant on ceiling height.
See diagrams for typical cases.
Compatibility
DALI and DALI-2
Power source
DALI line
DALI line capacity
Connects to 1 DALI line
DALI operating voltage
16 V dc (nominal), with suitable operation from 9.5 V –22.5 V
DALI line current draw
2 mA (nominal)
Mains tolerance
DALI input and auxiliary input are mains voltage tolerant
DALI connection
4 Tunnel Terminal block
Each tunnel suitable for 1 x 2.5 mm2or 2 x 1.5 mm2
Auxiliary connection
2 Tunnel Terminal block
Each tunnel suitable for 1 x 2.5 mm2or 2 x 1.5 mm2
Maximum auxiliary cable length
25 m –twin core mains cable ≥ 0.75 mm2
Auxiliary input types
Momentary switch, toggle switch or motion sensor voltage-free contacts
Indicators
DALI Operation: 1 x green, rear near terminal block
Identification: 1 x green, front through sensor lens
Ambient operating temperature
0 to 50○C
Ambient storage temperature
-10 to 70○C
Humidity
0% to 95% RH non-condensing
Ingress protection
IP20
Materials
Enclosure –Flame retardant Polycarbonate, UL 94V-0
Weight
100 g
Number of DALI Short addresses used
None –this sensor does not use a DALI Short Address
DALI addressing types supported
Short Addresses, Group Addresses, Scenes, Broadcast
Number of Xi extended addresses used
One
Xi occupancy sensors per DALI line
Up to 20 per DALI line
Additional addressing types*
RAPIX Zones, RAPIX Flags, RAPIX Operating Properties
Approvals
*
RAPIX features and additional addressing types work with other RAPIX products.
Commissioning
Use the free RAPIX Addressing or RAPIX Integrator software, available at ozuno.com.
A RAPIX USB Interface or Zone Controller is required to connect the commissioning software / PC to the DALI line.
Mounting
The recommended mounting height is in the range 6 to 10 metres.
Mounting Options
In-Ceiling Mount
Mount into a 61-72mm diameter hole in the ceiling. Sensor is retained by the
pre-fitted springs.
Optional Surface Mount Adaptor
(order separately)
Screw the Surface Mount adaptor over a conduit box , or break out the
conduit entry knockouts and screw the Surface Mount Adaptor directly to
the mounting surface.
Remove pre-fitted retaining springs and plastic posts from the Sensor using
side cutters. Wire as normal and clip Sensor into the Surface Mount Adaptor.

RAPIX Xi DALI Long Range Occupancy Sensor DGOZ-LRS-PRLLSW
Page 3 of 4
Detection Range
10 m mounting height
6 m mounting height
0m
4m
4m
8m
8m
12m
12m
10m
0m
0m 4m
8m 12m
4m 8m
12m
Side View
Top View
0m
4m
4m
8m
8m
6m
0m
0m 4m 8m
4m
8m
Side View
Top View
Standards and compliance
The product is designed to meet/exceed the following Australian and International standards:
EMC and Electrical Safety Frameworks and Standards
IEC/EN 55015, AS/NZS CISPR 15, AS CISPR 15
EN 55032, AS/NZS CISPR32
EN 55035
EN 61547
EN 61347-2-11, AS/NZS 61347.2.11
EN 61347-1, AS/NZS 61347.1
EN 62368-1
DALI Standards and Compliance
IEC 62386-101
IEC 62386-102
EC Council Directives
2014/35/EU Low Voltage
2014/30/EU Electromagnetic Compatibility (EMC)
2015/863 Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment
Separately Available Accessories
Surface Mount Adaptor
Screw mount, 50 mm and 60 mm spacings.
Order code (white): DGOZ-SEN-SMH.
Order code (black): DGOZ-SEN-SMH-BK.
Field of view mask
Allows limiting field of view by angle and segments.
Order code DGOZ-SEN-FOV.

RAPIX Xi DALI Long Range Occupancy Sensor DGOZ-LRS-PRLLSW
Page 4 of 4
Product dimensions
76.0
48.0
61.0
75.8
65.0
SENSOR SURFACE MOUNT ADAPTOR
Warranty
This product has a TWO YEAR warranty against manufacturing defects. The warranty applies from the date of purchase.
Refer to ozuno.com for the full conditions for warranty and returns process. A summary of the process:
1. Contact the seller of the goods, or in their absence contact Ozuno to request a return goods authorisation.
2. When a return is authorised, the goods must be returned to Ozuno at the owners expense for technical evaluation.
3. The warranty claim will be evaluated by Ozuno and accepted if the goods are found to be faulty, or rejected if the
fault was caused by conditions beyond the responsibility of Ozuno. Considerations of installation, removal, return,
freight and testing are not the responsibility of Ozuno.
The Australian Consumer Law requires the inclusion of the following statement with this Warranty:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
L I G H T I N G
CONTROL SY STE M
Ozuno Trading Pty Ltd (Ozuno) reserves the right to alter the specifications, designs or other features of any items and to
discontinue any items at any time without notice and without liability. While every effort is made to ensure that all
information in this user and installation guide is correct, no warranty of accuracy is given and Ozuno shall not be liable for
any error.
Trademarks
RAPIX is a trademark of Ozuno Holdings Limited.
Identified trademarks and copyrights are the property of Ozuno Holdings Limited unless otherwise noted.
© Copyright
This user and installation guide is copyright to Ozuno Holdings Limited. Except as permitted under relevant law, no part of
this user and installation guide may be reproduced by any process without written permission and acknowledgement to
Ozuno Holdings Limited.
Ozuno Trading Pty Ltd
ABN: 96 621 194 483
Contact
Technical Support: [phone] (Australian Eastern Standard Time)
Or: [e-mail]
Version 2, May 2021 Item 14-20-504-001-02