Raplink SD-19005 User manual

Device User Manual
Device : Door sensor
Model number : SD-19005
Product description
1. Working in 802.11 b/g/n 2.4GHz wireless network (no hub required).
2. Wi-Fi network configuration with EZ (Smart Config) and AP (access Point) mode.
3. Powered by 2xAAA battery for lasting 6 months depending on alarm frequency.
4. Real state (open/close) monitor in APP.
5. Notification with Open/Close, Tampered and Low battery (less than 10%).
6. Enable/disable notifications on Open/Close, tampered, low battery event in APP.
7. Indicate the battery level in APP.
8. Open/Close history record.
9. Share device in family.
10. Dual color LED status indicator.
11. Mounting with adhesive tape or screw.
12. Works with Google Home.
This main device components are showed as followed :
Device part Magnet part

3. Tamer button : Loose this button will trigger a tempered Alarm to Mobile Phone.
4. LED indicator : indicate the device working state.
- Fast blinking in Red : EZ mode (smart config) for Wi-Fi configuration.
- Slow blinking in Red : AP mode for Wi-Fi configuration.
Note :
Specification
Connection
1. Download RAPLINK App
RAPLINK is available for both iOS and Android OS.
Search the name 'RAPLINK' in App Store or Google Play to download the App.
click here to download
click here to download
2.4GHz ~ 2.484GHz
2*AAA battery, 3V
802.11b: -72dBm@MCS7_HT20 10%PER
802.11b: -75dBm@54Mbps 10%PER
802.11b: -91dBm@11Mbps 8%PER
802.11b: 13dBm+2dBm@MCS7_HT20
802.11b: 15dBm+2dBm@54Mbps
802.11b: -28dBm max.@MCS7_HT20
802.11b: -28dBm max.
802.11b: <35%
802.11b: 17dBm+2dBm@1Mbps
IEEE802.11 b/g/n
Working temperature
Storage temperature
Relative humidity
8% ~ 80%
=-20 ~ +60OC
=-10 ~ +40OC
2. To check the device is Wi-Fi connected or not : If the LED indicator turns purple, the device is non Wi-Fi connected.
If the LED indicator turns blue, the device is Wi-Fi connected.
1. Latch button : press the Latch button to take apart the battery cover from the device part in order to change the
batteries or setup the Wi-Fi network.
2. Button : Long press for 5s this button to enter the Wi-Fi network mode. Switch between EZ and AP mode by long
press the button more than 5s.
- Flash once in Blue : Wi-Fi network connected, short press the temper button or move the magnet from the device
part to flash the Blue.
- Flash once in Dual-Color : No Wi-Fi network connected, short press the temper button or move the magnet from the
device part to flash the Dual LED.
1. To check the device is working or not : Press the tamper button or move the magent part to close the device, the
LED indicator will flash.
Power supply
Wireless frequency
Network protocol
Transmitting power
Receiving sensitivity
Vector error EVM

2. Register an account
Register a RAPLINK App account if you don't have.
Tap to enter registration page to set up a RAPLINK account.
3. Add/connect device
Step 2 : Press button for 5 seconds to pair with the RAPLINK App. The LED indicator will flash rapidly. Tap the
"Confirm indicator rapidly blink".
Step 1 : Open the RAPLINK App, click "+" or "Add Device". Then select "Home Appliance" and "Door/Window".
c

Step 4 : Tap "Completed" to complete the connection process.
Control device
After successfully configuring the device, the motion sensor device will shown on the home page.
Tap the icons to view.
* Notes :
1. All figures display Android interfaces, IOS versions may vary slightly.
3. Further changes made will not be separately disclosed.
Step 3 : Select the WiFi under which device is working. Enter WiFi password and tap "Ok" to enter network
connection process.
2. Products and software are constantly being updated. Data and software interfaces shown here are for reference
purposes only.
cv
c