RATTAN Pathfinder User manual

EBIKE USER MANUAL
Pathfinder/Pathfinder ST

Thanks for your Patfhfinder Ebike
purchase!
We take pride in bringing you a quality product that will offer years of enjoy-
ment. Please feel free to contact us if there are any questions about
the bike.
Congratulation on your purchase of a new Rattan Ebike! The bike
comes 85% assembled and here is the guide that helps you get familiar
with your new bike in unboxing.
The bike may need adjustments in this process as shipping can some-
times be bumpy. We recommend an adjustment and inspection by a
reputable, certified bicycle mechanic before the first riding.
Please read the whole manual patiently before you use the new electric
bike, for technical assistance or warranty claims contact Rattan Ebike at
Phone: [phone]am-5pm (PST)
E-mail: [e-mail]
Web:www.rattanebike.com

CONTENTS
Using this manual.......................................................................................01
General information................................................................................... 02
Assembly instructions for Patfhfinder series .......................................... 02
Adjustment for comfort and safety.......................................................... 06
Riding guidance.......................................................................................... 09
Display.........................................................................................................11
Operating safety......................................................................................... 22
Troubleshooting......................................................................................... 24
Disclaimer................................................................................................... 26
Limited warranty.........................................................................................27

—1—
USING THIS MANUALS
This manual contains details of the product, its equipment, and inform-
ation on operation, maintenance, and other helpful tips for owners.
Read it carefully and familiarize yourself with the ebike before using it
to ensure safe use and prevent accidents. This manual contains many
warnings and cautions concerning the safe operation and conse-
quences if proper setup, operation, and maintenance are not performed.
All information in this manual should be carefully reviewed and if you
have any questions you should contact Rattan immediately.
The notes, warnings, and cautions contained within the manual and
paragraphs marked by the triangular Caution Symbol on the left side
and should be given special care. Users should also pay special atte-
ntion to information marked in this manual beginning with NOTICE .
Keep this manual, along with any other documents that were included
with your bike, for future reference, however all content in this manual
is subject to change or withdrawal without notice.
Visit www.rattanebike.com/pages/user-manual accuracy of its docu-
mentation and assumes no responsibility or liability if any errors or
inaccuracies appear within.
Rattan E-bike assumes no liability for any harm, injury, or death of the
rider. Because it is impossible to anticipate every situation or condition
that will occur while riding, this manual makes no representations
about the safe use of bikes under all conditions. There are risks asso-
ciated with the use of any bike that cannot be predicted or avoided and
are the sole responsibility of the rider.

—2—
GENERAL INFORMATION
Please note that your Pathfinder may include components that look
different from those in the illustrations above and elsewhere in this manual.
Such changes help ensure uninterrupted shipping. Our engineers rigorously
test each component to guarantee quality and compatibility.
ASSEMBLY INSTRUCTIONS FOR
PATHFINDER SERIES
1. Unpack
Incorrect assembly, maintenance, or use of your ebike can cause
component or performance failure, loss of control, serious injury, or
death.If you are not sure you could correctly perform all assembly
steps in the manual, consult a local, certified, reputable bike me-
chanic.
WARNING
Fully assembled Pathfinder
Fully assembled Pathfinder
ST

—3—
2. Front Fork
1. Loosen the hub quick release to make enough space for the fork.
2. In case of the spring drops from the quick release, here are the or-
iginal position images of both sides of the hub quick release.
3. The two feet of the front fork must be aligned with the hub quick
release position before the fork can be installed.
3. Handlebar
1. Tighten the screws on the stem.
2. Loosen the screws on the handlebar.
3. Hold the handlebar in the middle of the joint, tighten the screws.

—4—
4. Front fender
Fix the fender to the front fork with the screws on each side as the pic
shown.
5. Headlight
1. Unscrew the screw for headlight.
2. Connect the front fender, the connecter of the front fork, and the
headlight at the right position as the pic shown, then tighten the
screw.
6. Pedal

—5—
1. “ L” indicates the left side, “ R ” indicates the right side.
2. Make sure to tighten the screws connecting the pedals and cranks.
3. Twist to left when install the left side and twist to right when ins-
talling the right one.
7. Battery
1. Plug in the key and turn left to unlock the battery.
2. Picture 2 shows an Locked battery.
3. Picture 3 shows a Unlocked battery.
4. Take out the battery from the bike.
Charge the Ebike without removing the battery or Remove the battery,
and charge it.
8. Rear light cable
1
2
3
4
5

—6—
1. Fix the cable to the frame with the binder as the pic shown.
2. Connect the cable connector according to the direction of the arrow
on the two sides connector.
Connect all the connections following the color and the arrow direction
like this.
ADJUSTING FOR COMFORT & SAFETY
1. Adjust the Seat Height
An ideal seat height for most riders allows them to be comfortable and
get the best pedaling efficiency. When the rider is seated, they should
be able to place the ball of their feet on the pedal at its lowest position
The following steps are critical for your comfort and safety, and
must be performed before your first bike ride. We recommend that
you consult a bike fitting professional such as a certified, reputable
bike mechanic who specializes in bike fit.
WARNING

—7—
while their legs are almost fully extended, with the knee slightly bent.
The seat should never be so high that the rider must rock side to side
or fully straighten their legs while pedaling. And the seat must never be
pulled out so far that the minimum insertion point is above the seat
tube (see illustration).
2. Derailleur
1. Adjust the screw on the shifting wire when it is hard to switch the
shifter.
2. Loose screw 1 slightly when the shifter can't switch to the 7th gear.
on the contrary, if it can't gear down to the 1st level, loose screw 2
slightly and try again.
Overextending the seatpost can cause it to break or fall off your
bike, which will put you at a very high risk of serious injury or death.
Avoid this danger by inserting your seatpost into the seat tube far
enough that the minimum insertion point is no longer visible.
WARNING

—8—
3. Loosen screw 1 and 2 to make the derailleur move slightly away
from the rim in case of the chain rubs the tire.
4. Tighten the screw when the shifter can`t switch to the highest gear.
PREPARING TO RIDE
Checklist
01. Make sure all components especially fasteners and accessories
are tightened. Adjust the height of the handlebar and the seat post.
DO NOT raise it above the safety line.
02. Make sure the brakes can cut off the power supply to the motor,
and whether it is sensitive and reliable.
03. Make sure the front and rear axle nuts are tightened.
04. Make sure the display, brakes and lights can work properly.
05. Make sure the chain is tight.
06. Make sure the pedals and all the connection parts are firm and
would not loose, and whether the crank is flexible without jamming.
07. Check if the tire pressure exceeds the recommended one marking
on the side of tire walls.
08. Make sure the throttle works well without jamming, and whether it
feels tight or loose when pressing the throttle.
09. Make sure the battery has been locked.
10. Check if the total weight the bike carried is higher than 300lbs,
which is the maximum weight capacity of the bike.

—9—
RIDING GUIDANCE
Three Modes
•Pedal Mode
This mode does not require any power. It allows the ebike to work like
other regular bikes. You will be automatically switched to this mode
when the battery dies while riding.
• Electric Mode
Turn on the display and press the throttle slowly to get started. When
releasing the throttle slowly, the riding speed will gradually drop until
power off.
•Pedal Assist Mode
The rider can engage the pedal assist system (PAS) while pedaling,
and it will call up assistance from the motor to help propel the bike
forward. Pedal assist uses a cadence sensor built into the drive train of
the bike. The cadence sensor detects when the rider revolves the
pedals and signals the electric motor to provide the level of pedal
Incorrect assembly, maintenance, or use of your ebike can cause com-
ponentorperformancefailure, loss of control, serious injury, or death.
If you are not sure you could correctly perform all assembly steps in
the manual, consult a local, certified, reputable bike mechanic.
WARNING

—10 —
assistance (0-5)(0-4) that the rider has selected.
Notice Accelerate slowly and use the pedal assist at the beginning of
riding. When riding against the wind or climbing the hill, avoid using the
pedal assist to protect the battery.
• Throttle Mode
The throttle is located on the right side of the handlebar. The rider can
use it with a twist of the throttle grip to propel the bike forward without
pedaling.
To engage the throttle while riding, slowly and carefully rotate it toward
yourself. The more you twist, the more powerfully the motor will propel
the bike forward. Once you release the throttle or apply the brakes, the
throttle will no longer propel the bike forward. Always keep one hand
on the brake lever and be prepared to squeeze the lever to disengage
the throttle if needed, or turn off the bike to prevent accidentally
engaging the throttle.

—11 —
DISPLAY
•Display Interface

—12 —
1. Press the “i” button to display different information.
(2) Total miles
traveled
(3) Maximum
speed
(4) Average
speed
(1) Miles
traveled
(5) Total traveled
time

—13 —
2. Driving Mode Switching.
(1)Eco Mode
Activates at a slow speeds providing low acceleration (Low energy
Xconsumption).
(2)Normal Mode
Activates at a normal speeds providing normal acceleration(Normal
Xenergy consumption).
(3)Sport Mode
Activates at a high speeds providing high acceleration (Higher
Xenergy consumption).
3. Switching Walk-assistance Mode On/Off
(1) Walk-assistance function may only be used when you walking the
E-bike.
(2) To activate the walk-assistance function, press the “-” button for 2s.
(3) The walk-assistance function will be switched off as soon as you
release the button.

—14 —
4. Assistance Level Selection
(1) Press "+" or "-" button to switch the E-bike system assistance level
to change the motor output power.
(2) The default assistance level ranges from level“0”to level“5”.
(3) The output power is zero on Level “0”. Level “1” is the minimum
power. Level “5” is the maximum power.
(4) The default value is level “0”.
•Introduction of Common Functions
The following functions must restart the display after set-
ting the instrument to take effect.
1. Setting Access
(1) Press both the “+” button and the “-” button for 2s to access general
settings menu.
(2) All the Settings are operated in this page.

—15 —
2. Key-Disp App Guide
(1) Download
Download from apple store/google store by key words “Key-Disp”. App
logo is as follow:
(2) Sign Up & Log In
Fill in the required information according to pictures below to sign up
and log in.

—16 —
(3) App Connection
App must connect with the ebike system to realize all its functions.
When display is on, Add Device > Add > “+” Button > Done.