Ravas iCP User manual

We would like to inform you about the fact that this RAVAS product is 100% recyclable, provided that parts
are being processed and disposed of in the right manner.
More information can be found on our website: www.ravas.com
Rev. 20220421
Printing/Typographical errors and model changes reserved.
iCP
wireless and cabled
USER MANUAL - iCP 1
Owner’s Manual

USER MANUAL - iCP 2
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
If you have any queries concerning the duration and terms of the RAVAS warranty, please
contact your supplier or check our General Sales and Service Conditions, which are available
on request.
The manufacturer accepts no liability for any damage or injury caused by failure to follow these
instructions, or from negligent operation or assembly, even if this is not expressly stated in this
instruction manual.
In light of our policy of continuous improvement, it is possible that details of the product may
di󰀨er from those described in this manual. For this reason, these instructions should only be
considered as guidelines for the installation of the relevant product. This manual has been
compiled with all due care, but the manufacturer cannot be held responsible for any
consequences of errors. All rights are reserved and no part of this manual may be reproduced
in any way.

USER MANUAL - iCP USER MANUAL - iCP
2 3
Table of Contents
1. Introduction 4
2. Warning & Safety measures 4
3. Wireless system - system setup and battery change 5
3.1 Installing the indicator 5
3.2 Placing the battery pack in the iCP 6
3.3 Connecting and switching on the iCP 6
3.4 Switching o󰀨 the system 7
3.5 Low battery indication iCP 8
3.6 Removing the rechargeable battery pack 8
3.7 Charging the battery pack 9
4. Cabled system - system setup 10
4.1 Installing the indicator 10
4.2 Mast cabling (example) 11
4.3 Indicator power supply from fork lift truck battery 12
4.4 Connecting and switching on the iCP 13
4.5 Switching o󰀨 the system 13
5. Use 14
5.1 Use (accurate weighing) 14
5.2 Level correction (option) 15

1. Introduction
2. Warning & Safety measures
When using the iCP, please observe the instructions
and guidelines contained in this manual carefully.
Always perform each step in the rigth sequence. If any of the
instructions is not clear, please contact RAVAS.
This manual describes the installation and use of the iCP. Read this manual carefully. The
installer must be informed of the contents of this manual. Always do things in the correct order.
This manual should be kept on a safe and dry place. In case of damage or loss the user may
request a new copy of the manual from RAVAS.
• All safety regulations that apply to the truck remain valid and unchanged;
• No weighing operations are allowed if any person or object is in the vicinity; around,
under or close to the load;
• RAVAS is not responsible for any physical harm done to the operator as a result of
coming into contact with the indicator in the cabin;
• Any modications done to the system must be approved in writing by the supplier, prior to
any work being completed;
• It is the sole responsibility of the purchaser to train their own employees in the proper use
and maintenance of this equipment;
• Do not operate this unit unless you have been fully trained in its capabilities;
• Check the accuracy of the scale on a regular basis to prevent faulty readings;
• Only trained and authorized personnel are allowed to service the scale;
• Always follow the operating, maintenance and repair instructions of this truck and ask the
supplier when in doubt;
• RAVAS is not responsible for errors that occur due to incorrect weightings or inaccurate
scales.
Should you have any further questions after reading this manual then you can contact us at:
RAVAS USA, INC.
1500 Enterprise Pkwy
Twinsbrug, OH, 44087
United States
IP65
min -10°C
15°F
00
max 40°C
105°F
READ
CAREFULLY
!
Phone:[phone]
Email:saleso󰀩[email protected]
Website: www.ravas.com
USER MANUAL - iCP 4

3. Wireless system - system setup and battery change
3.1 Installing the indicator
Find a suitable position for the indicator:
1. at the cabin’s roof.
2. on the right side of the cabin, mounted onto a side-rail.
3. on the dashboard.
Installation of the indicator bracket and support.
S13
1.
2.
S5
3.
3
2
1
The indicator should be
easy to reach and read!
Please note: in this manual we have
used images of the 3200 indicator as an
example! The functionality of the iCP is
the same with any other indicator.
USER MANUAL - iCP USER MANUAL - iCP
4 5

3.2 Placing the battery pack in the iCP
1. Push the red locking clip down to unlock the battery holder of the iCP
2. The battery holder will open automatically.
3. Position the battery pack in the battery holder until the red locking clip shifts up again.
4. Close the battery holder until you hear a “click”.
3.3 Connecting and switching on the iCP
1 2
e1 e2 e3 F1 F2
NET
ID CODE PT TOTAL KG/LB
CLR
Start up the
indicator. Press
the on/o󰀨 key.
OR
Switch on the iCP:
Move the iCP quickly in upwards or
downwards direction.
USER MANUAL - iCP 6

The Bluetooth link between the indicator and
the carriage plate will connect automatically.
The iCP is “ACTIVE” when the blue LED on the
plate ashes repeatedly.
3
After 5 seconds all electronics are warmed up and you can start weighing.
3.4 Switching o󰀨 the system
12
e1 e2 e3 F1 F2
NET
ID CODE PT TOTAL KG/LB
CLR
3 sec.
Switch o󰀨 the indicator
by pressing the on/o󰀨
key for 3 seconds. The carriage plate will switch o󰀨 automatically.
The blue LED “SLEEP” on the carriage plate will
start blinking automatically.
USER MANUAL - iCP USER MANUAL - iCP
6 7

3.5 Low battery indication iCP
Exchangeable battery pack supplies power to the iCP.
When the voltage level of the battery pack is running low, the low battery indicator will light up
and “F1” will start ickering in the display.
The blue LED on the bluetooth module will start ickering very slowly (twice every 10 sec).
The iCP will switch o󰀨 automatically after 10 minutes.
FUNCTIONALITY BLUE LED
DURING POWERING ON ON for 5 sec.
FULL BATTERY Flicker time interval
Working mode Once every 1,5 sec.
Sleep mode Once every 12 sec.
LOW BATTERY
Working mode Twice every 10 sec.
Sleep mode Twice every 10 sec.
3.6 Removing the rechargeable battery pack
1. Push the red locking clip down to unlock the battery holder of the iCP
2. The battery holder will open automatically.
3. Remove the battery pack from the battery holder.
USER MANUAL - iCP 8

3.7 Charging the rechargeable battery pack
The system is equipped with a rechargeable battery pack and a smart charger. Charge the
battery for 8 hours. This will prevent loss of battery capacity.
First position the battery pack inside the charger module, then plug the adaptor into the mains
voltage.
Smart charger: When the battery is being charged, the red LED on the charger is lit. After at
least 8 hours charging, the charger shuts o󰀨 and the the battery packs are completely full. The
red LED turns o󰀨 and the green LED will illuminate.
8 hours
1. 2.
USER MANUAL - iCP USER MANUAL - iCP
8 9

4. Cabled system - system setup
4.1 Installing the indicator
Find a suitable position for the indicator:
1. at the cabin’s roof.
2. on the right side of the cabin, mounted onto a side-rail.
3. on the dashboard.
Installation of the indicator bracket and support.
S13
1.
2.
S5
3.
3
2
1
The indicator should be
easy to reach and read!
Please note: in this manual we have
used images of the 3200 indicator as an
example! The functionality of the iCP is
the same with any other indicator.
USER MANUAL - iCP 10

4.2 Mast cabling (example)
Connector of the iCP
connected to the cable
of the indicator.
Always install the cable neatly in a loop so that
there will be no kink in the cable
Indicator mounted in the cabin.
USER MANUAL - iCP USER MANUAL - iCP
10 11

4.3 Indicator power supply from fork lift truck battery
+-
+
_Black
Red
Blue
Brown
EU US
READ LABEL ON BACK FOR POWER SUPPLY INDICATOR
POWER REGULATOR INSIDE + = 12 VDC
POWER CONVERTER INSIDE + = 20-100VDC
Only possible if indicator is equipped with an integrated voltage converter or voltage stabilizer.
USER MANUAL - iCP 12

4.5 Switching o󰀨 the system
1
e1 e2 e3 F1 F2
NET
ID CODE PT TOTAL KG/LB
CLR
3 sec.
Switch o󰀨 the indicator
by pressing the on/o󰀨
key for 3 seconds.
4.4 Connecting and switching on the iCP
1 2
e1 e2 e3 F1 F2
NET
ID CODE PT TOTAL KG/LB
CLR
Start up the
indicator. Press
the on/o󰀨 key.
OR
Switch on the iCP:
Move the iCP quickly in upwards or
downwards direction.
After 5 seconds all electronics are warmed up and you can start weighing.
USER MANUAL - iCP USER MANUAL - iCP
12 13

5. Use
5.1 Use (accurate weighing)
min -10°C
15°F
00
max 40°C
105°F
M1
3 - 5 min.
OK
M1
After 3 to 5 minutes the load cells have reached
the operational temperature. Don’t lift loads
before the zero-point correction has been
executed.
USER MANUAL - iCP 14

5.2 Level correction
TOTAL
e1 e2 e3 F1 F2
NET
PTID CODE KG/LB
CLR
α
OK
e1 e2 e3 F2F1
> α
NTEP: OK if α= +/- 5% (3°)
OIML: OK if α= +/- 2°
Check the zero reading
before each weighing!
Before each weighing it is necessary to
check whether the system is unloaded
and free.
If the indicator does not determine the
zero point automatically, it must be
done manually using the >0< key.
Legal for trade:
USER MANUAL - iCP USER MANUAL - iCP
14 15