Excell H4 Series User manual

H4 Series and X Series
Counting Scale
User Manual
© EXCELL PRECISION CO., LTD. 2021. All rights reserved worldwide.
The information contained herein is the property of EXCELL PRECISION CO., LTD. and is
supplied without liability for errors or omissions. No part may be reproduced or used except as
authorized by contract or other written permission. The copyright and the foregoing restriction
on reproduction and use extend to all media in which the information may be embodied.

EXCELL PRECISION CO., LTD.
ZSME200000060
1
03005XXX/03006XXX
Table of Contents
PRECAUTIONS FOR USE..........................................................................................................3
PREPARATIONS BEFORE USING .............................................................................................3
CHAPTER 1 DISPLAY AND KEYPAD DESCRIPTIONS.............................................................5
1-1 DISPLAY DESCRIPTIONS ........................................................................................................5
1-2 POWER SUPPLY AND POWER CONSUMPTION...........................................................................6
1-3 KEYPAD DESCRIPTIONS.........................................................................................................6
1-4 ERROR MESSAGES ...............................................................................................................7
CHAPTER 2 OPERATION...........................................................................................................8
2-1 POWER ON...........................................................................................................................8
2-2 HIGH AND LOW RESOLUTION SHIFT SETTING...........................................................................8
2-3 ZERO FUNCTION ...................................................................................................................8
2-4 OBTAIN UNIT WEIGHT............................................................................................................8
2-4-1 Through Sampling.......................................................................................................8
2-4-2 Enter Known Unit Weight ............................................................................................9
2-4-3 Through Sampling Under Tare.....................................................................................9
2-5TARE FUNCTION OPERATION................................................................................................10
2-6 PRE-TARE FUNCTION OPERATION.........................................................................................10
2-7ACCUMULATION...................................................................................................................11
2-7-1 Quantity Accumulation...............................................................................................11
2-7-2 Weight Accumulation.................................................................................................12
2-8 QUANTITY PRESET..............................................................................................................12
2-9WEIGHT PRESET.................................................................................................................13
2-10 ID INPUT ..........................................................................................................................14
2-11 ITEM INPUT .......................................................................................................................14
2-12 UNIT WEIGHT PRESET.......................................................................................................14
2-12-1 Pre-set Unit Weight Operation (Read-in).................................................................14
2-12-2 Pre-set Unit Weight Saving Operation (Read-out)...................................................15
CHAPTER 3 EXTERNAL CALIBRATION SETTING..................................................................15
3-1 EXTERNAL FUNCTION SETTING ................................................................16
3-1-1 Backlight Mode Setting ..............................................................16
3-1-2 Auto. Power-off Setting ..............................................................17
3-1-3 Stable Range Setting for Quantity Sampling .............................17
3-1-4 Auto Average Unit Weight Setting .............................................17
3-1-5 A/D Sampling Speed Setting .....................................................17
3-1-6 Zero Display Range Setting ......................................................17
3-1-7 Zero Tracking Range Setting .....................................................17
3-1-8 Accumulation Ending Mode Setting ...........................................18
3-1-9 Pre-tare mode setting ................................................................18
3-1-10 “Beeper” Output Setting for Quantity Limit ................................18

EXCELL PRECISION CO., LTD.
ZSME200000060
2
03005XXX/03006XXX
3-1-11 Accumulation Acceptable Condition Setting 1 .............................18
3-1-12 Accumulation Acceptable Condition Setting 2 ...........................18
3-1-13 Combination Key Setting ............................................................18
3-2 EXTERNAL WEIGHTAND GVALUE CALIBRATION .............................................19
3-2-1 External Weight Calibration ..............................................................19
3-2-2 Calibrate G Value Used in Local or in Verification ............................20
3-3 RS-232AND SERIAL PRINTER SETTING ...................................................21
3-3-1 Baud Rate Setting ....................................................................21
3-3-2 Communication Protocol Setting ..............................................21
3-3-3 Output Data Format Setting ......................................................21
3-3-4 Continuous Output Count Setting Per-second ..........................22
3-3-5 Operation Mode Setting ............................................................23
3-3-6 Continuous Transmission Output Condition Setting .................24
3-3-7 Zero Band Setting for Auto. Transmission ................................24
3-3-8 Weight Band Setting for Auto. Transmission ............................25
APPENDIX 1 RS-232 FULL DUPLEX FORMAT........................................................................25
APPENDIX 2 FIXED FORMAT RS-232 TRANSMISSION LINE DESCRIPTION.......................27
APPENDIX 3 ASCII CODE TABLE ............................................................................................28
APPENDIX 4 7-SEGMENT DISPLAY CHARACTERS...............................................................28
Check Firmware Version
Turn on scale and hold ZERO key during countdown. Display “SELF tESt” and then
display
. Press MC key to show firmware version 03005 (H4 series) or
03006 (X series). Press MC key again to show maintenance number XXX ranged
from 000~999. Turn off and turn on scale to return to weighing mode.

EXCELL PRECISION CO., LTD.
ZSME200000060
3
03005XXX/03006XXX
Precautions for Use
1. The scale should not be drenched by rain or water. (If it gets wet carelessly, please wipe it
dry with a cloth. If its operation is abnormal, please send it to our distributor for service)
2. Please keep the scale clean. Please keep the scale in a cool and dry place. Do not store
at high temperature or damp places.
3. Use within the maximum capacity.Avoid sudden drop of heavy object on the platter.
4. The rechargeable battery is consumables and is not included in the warranty. If scale is
not used for some time, please clean and store it in a plastic bag with desiccative. The
rechargeable battery should be recharged every three months. (If using dry batteries, take
the dry batteries out before storing)
The numbers of recharges for battery vary with the conditions of use. It can be maximized
by re-charging the battery frequently and by avoiding conditions of total discharge.
5. The commodity should be placed in the center of platter for accurate weighing. The
dimension of the weighted commodity should not exceed the dimension of platter.
6. Please operate or charge the scale in an open area. Avoid squeezing the power cable,
which might cause short circuit within cable and result in fire. When charging, the charging
indicator will light up within 4-6 seconds. Green -> The battery is fully charged. Red ->
charging is in progress.
7. Operating temperature: -10°C ~ +40°C
8. Recommendation: Use this product in an indoor environment with altitude up to 2000m.
9. If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
10. Any suggestion for the product is warmly welcome.
Preparations before Using
1. Put the scale on a firm and flat surface for accurate weighing reading. Adjust the four
leveling feet to get the leveling bubble at the center of the circle.
2. Scale must be used under a stable temperature and stable air flow. Avoid direct sunlight
onto the scale or use near air vent.
3. Scale must be used under individual socket to avoid the interference of other electric
appliances.
4. Clear the platter before turning on the scale. It requires 15 ~ 20 minutes to warm up.
5. When the low power warning symbol flashes, If not charge immediately, auto
shut-down within 5~10 hours or 1~2 hours with backlight for H4 series. For X series, it
auto shut-down within 8~12 hours or 3~6 hours with backlight. Once it auto shut-down and
enter the battery protection mode, it must be charged before it can be used.
Thank you for purchasing EXCELL counting scale.
In order to operate smoothly, to last the durability
and to reduce chance of breakdown for this product,
Please read this manual carefully.

EXCELL PRECISION CO., LTD.
ZSME200000060
4
03005XXX/03006XXX
No burning
Caution Corrosion
6. Lead-Acid Battery Notice
Lead-acid battery adopts the advanced free-maintaining technique, customers need not to
replenish electrolyte. The scale should be recharged every 3 months to battery
over-discharged and shorten the life of the battery.
1. The battery should be fully charged for 8~10 hours.
2. The temperature of battery should be below 45°C.
Maintaining
1. To ensure the service life of the battery, please do not over-discharge the battery and charge
the battery whenever low power warning symbol flashes.
2. Please remove the battery when the scale is not used for a long time or disconnect the cable
at cathode from the battery. Checked voltage of battery frequently and if voltage is low,
charge the battery in time.
3. Do not short the battery terminals to check if there is still current. Please check if the
connection point is firm to guarantee good connection.
4. The battery should be replaced by specialized person. No reverse-battery or the product
will be damaged.
a) Anode of battery should be connected with Anode of power cable (usually red cable)
b) Cathode of battery should be connected with Cathode of power cable (usually brown
cable or black cable)
Safety warnings
1. The electrolyte of battery is caustic which causes metal, cotton, etc to corrode.
2. The hydrogen will be resolved when using or charging the battery and it will cause explosion
when approaches fire.
Brown cable(or black cable)
connected with Cathode of
battery
Red cable connected with
Anode of battery
Warning explosion
Children faraway

EXCELL PRECISION CO., LTD.
ZSME200000060
5
03005XXX/03006XXX
Chapter 1 Display and Keypad Descriptions
1-1 Display Descriptions
Non-approval models: = ~ or resolution equal to 1 / 3,000
WEIGHT
UNIT WEIGHT
QUANTITY
o

.....

......
+

......


stable

Approval models: = ~ and resolution equal to 1 / 3,000
WEIGHT
UNIT WEIGHT
QUANTITY
o

.....
PT

......
+

......


stable

Display Column
1. WEIGHT
Total 6 digits. To display the weight or the total accumulation weight; 1st left digit can display “-“.
2. UNIT WEIGHT
Total 6 digits. To display the unit weight of objects on the platter or total accumulation counts.
3. QUANTITY
Total 6 digits. To display the quantity of the objects on platter or the accumulated quantity.
Symbol Icons “”
1. or Net or Tare : “Tare” indication
2. oor Zero :“Zero” indication
3. + or M+ :“Accumulation” indication
4. Stable :“Stable” indication
5. PT :“Pretare” indication (for approval models)
6. :(For non-approval models) If sample weight < minimum required weight, this symbol will
display. Please add more samples and then sample again. Minimum required weight is defined:
10d for resolution in 1/3000 and 20d for resolution range from 1/6000 to 1/30000
If symbol displays, scale can still be used but may affect the counting accuracy.
7. :If the unit weight of the object < “Minimum Unit Weight”, this symbol will display. Please
use scale with smaller division. “Minimum Unit Weight” is defined:
0.1d for resolution in 1/3000 and 0.2d for resolution range from 1/6000 to 1/30000
If symbol displays, scale can still be used but may affect the counting accuracy.

EXCELL PRECISION CO., LTD.
ZSME200000060
6
03005XXX/03006XXX
1-2 Power Supply and Power Consumption
100~240Vac, 50/60Hz
H4 series
X series
Software version
03005XXX
03006XXX
Battery
6V / 4Ah lead acid battery
3.7V / 6100mAh Li battery
Consumption
(without backlight)
33mA / 0.20W
Operation time: 108 hours
27mA / 0.11W
Operation time: 120 hours
Charging time
8~12 hours
5~6 hours
Battery
status
>= 6.2V
>= 3.8V
< 5.7V
< 3.52V
Auto
shut-down
< 5.6V
<3.42V
1-3 Keypad Descriptions
[Standard keypad]
7

8
ABC
9
DEF
SAMPL
Q’TY
PST
4
GHI
5
JKL
6
MNO
UNIT
W.T
PST
CE
1
PQRS
2
TUV
3
WXYZ
Z
M+
0
.
CE
T
MC
[Double weighing units keypad]
7

8
ABC
9
DEF
SAMPL
Q’TY
PST
4
GHI
5
JKL
6
MNO
UNIT
W.T
kg/lb
1
PQRS
2
TUV
3
WXYZ
Z
M+
0
.
CE
T
MC
[10 sets of preset unit weight keypad]
7

8
ABC
9
DEF
SAMPL
Q’TY
PST
4
GHI
5
JKL
6
MNO
UNIT
W.T
U.W
PST
1
PQRS
2
TUV
3
WXYZ
Z
M+
0
.
CE
T
MC

EXCELL PRECISION CO., LTD.
ZSME200000060
7
03005XXX/03006XXX
Key Function
,~
:
Number key for setting the unit weight, quantity and etc.
:
Clear key to clear the digits on the display.
:
Unit weight key for setting the unit weight of sample.
ZERO or
:
Press this key, the display returns to 0.
TARE or
:
Press this key to deduct the weight of container. Or shift the digit pointer to left.
:
Pre-setting the upper limit of count. If the calculated count is larger than the
limit, the scale sends a warning sound. Or use this key to confirm the setting.
:
Totalizing the quantity or weight.
:
Clear the stored totalizing memory. Or shift the digit pointer to right.
Different keys for different models:
:
Press this key to clear preset.
:
Press this key to switch the unit : kg or lb
:
Press this key to preset the unit weight of sample. Or use this key to enter the
setting mode.
:
Press this key and release it within 3 seconds, then user can increase or
decrease the number of decimal places. Or press this key over 3 seconds,
the display resolution will change from 1/3,000 to 1/30,000 temporarily. The
display resolution will return back to 1/3,000 after 5 seconds.
1-4 Error Messages
E1 zero value is too high (OMIL or NTEP ＞10% full scale)
E2 zero value is too low (OMIL or NTEP ＜10% full scale)
E6 Internal value ＞700,000 (use in factory calibration)
E7 Internal value ＜100,000 (use in factory calibration)
oL The weight value is over 9d of the maximum capacity. (d = division)
unStAbLE Internal value is unstable (Unstable over 10 seconds after pressing ZERO or
TARE key)

EXCELL PRECISION CO., LTD.
ZSME200000060
8
03005XXX/03006XXX
Chapter 2 Operation
2-1 Power On
SW switch on (Press SW to location “ ”)
WEIGHT
UNIT WEIGHT
QUANTITY
After stable, the scale will count back to zero.
WEIGHT
UNIT WEIGHT
QUANTITY
600 ⇒Maximum countable data: 600 000 Sampling Speed
After return to zero and being stable, scale will enter into counting mode.
2-2 High and Low Resolution Shift Setting
Only for 1/3,000 resolution models
The function is subject to OIML and Brazil Approval models.
Press key and then release this key in 2.5 seconds until 3 seconds, this key has decimal
function.
Press key and then not to release in 3 seconds, the resolution in weight column will
convert to 1/30,000 and return back to 1/3,000 in 5 seconds.
When resolution converts to 1/30,000, key and Printer are not available.
2-3 Zero Function
While operating the scale, zero may sometimes fluctuate. (Slight weight changes happen in
weight column.) Press ZERO key to return to zero.
2-4 Obtain Unit Weight
2-4-1 Through Sampling
1. Place the sampling object on platter
.
Weight on platter
2. Enter the quantity of the sample on platter
.

Weight on platter Enter the sampling quantity
The number of quantity column will flash 6 seconds. If the user doesn’t press the SAMPLE
key before flashing is over, the scale will complete the unit weight setting procedure
automatically after flashing. The scale will also take the number that inputted in unit weight
column as the unit weight of object to calculate the quantity of object shown in quantity column.

EXCELL PRECISION CO., LTD.
ZSME200000060
9
03005XXX/03006XXX
3. Press SAMPLE key while total column number is flashing
.
Weight on platter
4. After stable, the scale finishes sampling and enters into counting mode
.
.
stable

Weight on platter Unit weight of object Enter sampling quantity
2-4-2 Enter Known Unit Weight
1. Enter known unit weight of object intended to weigh
o

.
.

stable

Unit weight of object intended to weigh
2. Press UNIT WEIGHT key to complete setting and enter into counting mode
o

.
.
stable

Unit weight of object intended to weigh
2-4-3 Through Sampling Under Tare
1. Take the sample off the platter
.
The weight of object on platter
2. Input the quantity of sample on the platter
.

The weight of object on platter Enter the quantity of sample
The number of quantity column will flash 6 seconds. If the user doesn’t press the SAMPLE
key before flashing is over, the scale will complete the unit weight setting procedure
automatically after flashing. The scale will also take the number that inputted in unit weight
column as the unit weight of object to calculate the quantity of object shown in quantity column.
3. Press SAMPLE key while the number of quantity is flashing
.
Weight of the object on platter
4. After stable, the scale finishes sampling and enters into counting mode
.
.
stable

Weight of the object on platter Unit weight of object quantity of sample entered
The larger quantity of sampling, the more precise unit weight counted out.
When unit weight column and total quantity column both indicate 0, please press
1UNIT WEIGHT key, and the previous unit weight value will come out. 
Use ZERO and 7 keys to turn on/off quantity display with negative weight.

EXCELL PRECISION CO., LTD.
ZSME200000060
10
03005XXX/03006XXX
2-5 Tare Function Operation
1. Place the packaging container on platter
.
Weight of packaging container
2. Press TARE key
3. The scale will enter into counting mode after stable
o

.

stable

Clear off the tare value
Mode 1: After removing the object together with packaging container, weight column will display
the negative value of packaging container. Press TARE key again to cancel the tare,
and return to zero. The tare symbol “”will disappear.
Mode 2: After removing the object together with packaging container, weight column will display
the negative value of packaging container. Press ZERO key again to cancel the tare,
and return to zero. The tare symbol “”will disappear.
2-6 Pre-tare Function Operation
(Pre-tare setting) is set up as . (No weight on platter)
1. No weight on platter
o

.
stable

2. Press TARE key
o

.
stable

3. Enter the known weight of packaging container
o

.

stable

weight of packaging container entered
4. Press TARE key
.


stable

(Pre-tare setting) is set up as . (Weight on platter)
For Non-approval models
1. Object placed on platter
.
.
stable

Weight of the object on platter Unit weight of the object Quantity of the object
2. Enter the known weight of packaging container
.
.

stable

Weight of packaging container entered

EXCELL PRECISION CO., LTD.
ZSME200000060
11
03005XXX/03006XXX
3. Press TARE key
.

.

stable

Weight of the object without container Unit weight of the object Quantity without packaging container
Pre-Tare function is also available even if tare is in operation.
If the net weight on platter is more than zero weight, the tare function is available. Otherwise,
it’s not capable of tare function.
Clear off Pre-tare value
After removing the object together with packaging container, weight column will display the
negative weight value of the packaging container. Press TARE key once again to cancel the
pre-tare value and return to zero. Then the tare and pre-tare symbol “”will disappear.
Recall Pre-tare value
1. Press Q’TY PRSET key, and then press TARE key
.


stable

Pre-tare value
2. After displays pre-tare value about 5 seconds, it automatically returns to the weighing mode
.

.

stable

Recall pre-tare value function and clear function are not available for Standard keypad
models.
2-7 Accumulation
The accumulation counts are up to 99 counts, but the total quantity column is at most 6 digits.
Users cannot do positive accumulation and negative accumulation at the same time.
2-7-1 Quantity Accumulation
1. Place an object on platter
.
.
stable

Weight of the object on platter Unit weight of the object Quantity of the object on platter
2. Press M+ key
3. After scale is stable
.
+

stable

Accumulated total weight Accumulated total counts Accumulated total quantity
4. After about 3 seconds, scale returns to counting mode
.
.
+

stable

Weight of the object on platter Unit weight of the object Quantity of the object on platter

EXCELL PRECISION CO., LTD.
ZSME200000060
12
03005XXX/03006XXX
Recall quantity accumulation
While weight column displays 0, press M+ key to recall the accumulated data
o

.
+

stable

Accumulated total weight Accumulated total counts Accumulated total quantity
Clear off the accumulated quantity value
Press MC key to clear off the accumulated value in the memory, and then accumulation
symbol “”will disappear.
2-7-2 Weight Accumulation
1. Place an object on platter when unit weight displays 0
.
stable

Weight of the object on platter
2. Press M+ key
3. After scale is stable
.
+

stable

Accumulated total weight Accumulated total counts
4. After about 3 seconds, scale returns to weighing mode
.
+

stable

Weight of the object on platter
Recall weight accumulation value
While weight column displays 0, press M+ key to recall the accumulated data
o

.
+

stable

Accumulated total weight Accumulated total counts
Clear off the accumulated weight value
Press MC key to clear off the accumulated weight in the memory, and then the accumulation
symbol “”will disappear.
2-8 Quantity Preset
It’s available to pre-set the upper limit of quantity in counting mode. If the counts are over the
limit, the beeper makes warning sounds, and the weight column displays flashing “ ”
Upper limit of preset quantity (Non-standard keypad)
1. Whether there is an object on platter or not, press Q’TY PRESET key. Press SAMPLE key,
select “Quantity Preset”mode (Press UNIT WEIGHT key to select “Weight Preset”mode)
o

stable

Previous preset value

EXCELL PRECISION CO., LTD.
ZSME200000060
13
03005XXX/03006XXX
2. Enter the upper limit intended (Press CE key to modify the value entered)
o

stable

Upper limit entered
3. Press SAMPLE key (Press CE key to modify the value entered)
o

stable

4. press Q’TY PRESET key, the scale return to the counting mode
o

.
stable

Clear off the pre-set upper limit
To clear the pre-set upper limit of quantity or weight, please follow the above-mentioned
operation steps. When entering the pre-set value, please enter “0”instead.
When switching to “weight preset”mode or “quantity preset”mode, previous preset value
will be deleted automatically.
If it is standard keypad, use number keys to enter number andthen press Q’TY PRESET key
to finish the setting; If to clear off the pre-set upper limit, press PRESET CE key.
2-9 Weight Preset
It’s available to pre-set the upper limit of weight. If the weights are over the limit, the beeper
makes warning sounds, and the weight column displays flashing “ ”
Upper limit of preset weight
1. Whether there is an object on platter or not, press Q’TY PRESET key. Press UNIT WEIGHT
key to select “Weight Preset”mode (Press SAMPLE key to select “Quantity Preset”mode)
o

.
.
stable

Previous preset value
2. Enter the upper limit intended (Press CE key to modify the value entered)
o

.
.
stable

Upper limit entered Previous preset value
3. Press UNIT WEIGHT key (Press CE key to modify the value entered)
o

.
.
stable

4. press Q’TY PRESET key, the scale return to the counting mode
o

.
stable

Clear off the pre-set upper limit
To clear the pre-set upper limit of quantity or weight, please follow the above-mentioned
operation steps. When entering the pre-set value, please enter “0”instead.
When switching to “weight preset”mode or “quantity preset”mode, previous preset value
will be deleted automatically.

EXCELL PRECISION CO., LTD.
ZSME200000060
14
03005XXX/03006XXX
ID could be set up to 12 digits. They can be numbers (0~9),
English letters (A~Z), or 
Press key to quit setting
Item could be set up to 12 digits. They can be numbers
(0~9), English letters (A~Z), or 
Press key to quit setting
2-10 ID Input
Press ZERO key, and the screen displays “- - - - - -”. Press 0 key before it disappears.
Enter ID with number keys
Press MC key to confirm
o

.
stable

2-11 Item Input
Press ZERO key, and the screen displays “- - - - - -”. Press 2 key before it disappears.
Enter Item with number keys
Press MC key to confirm
o

.
stable

ID & ITEM are applied in FIX FORMAT or FREE FORMAT.
ID & ITEM could be set up to 12 digits. They can be numbers (0~9), English letters (A~Z), or .
Entering numbers/English letters: Press number key and the digit flashes. Press the same key,
and the display shows the number/English letter in cycle. When the entered number/English
letter flashes for 2 seconds, the setting will be confirmed and moved to the right place by 1
digit. For example: Press 1 key continuously, and the screen displays 1,P,Q,R,S flashing in
cycle.(If to enter too many numbers, please enter to clear superfluous numbers.)
If ID & ITEM are not saved in unit weight preset, the data will be cleared after power off.
2-12 Unit Weight Preset
The preset data could be saved in up to 50 addresses
Each address contains: unit weight pre-tare ID and ITEM
2-12-1 Pre-set Unit Weight Operation (Read-in)
Use number keys to enter the unit weight. (The value is 0 or blank without setting)
Press U.W. PST key

EXCELL PRECISION CO., LTD.
ZSME200000060
15
03005XXX/03006XXX
Press U.W. PST key again
Press number keys to select 1 of 50 addresses for saving the data. If it is over 50,
Please re-enter.
Press U.W. PST key
2-12-2 Pre-set Unit Weight Saving Operation (Read-out)
Press U.W. PST key again
Use number keys to enter preset group that you want. If it is over 50, Please re-enter.
Press U.W. PST key again to read-out the data you saved. If the data is blank, it shows NULL.
While read-in or read-out, if the waiting time is over 10 seconds, the scale returns to weighing
mode automatically. Press CE key to cancel the read-in and read-out.
Chapter 3 External Calibration Setting
After starting the machine and it returns to zero, press ZERO key and the screen displays
”- - - - - -“. Then press key to enter external calibration function setting mode. The weight
column displays .
Press TARE key
Press TARE key
Press TARE key
Press TARE key
External Function Setting
External Weight Calibration
and G Value Calibration
RS-232 and Serial Printer Setting
Exit the Setting
11Exit
1CE Move cursor leftward
1TARE Move cursor rightward
1MC Enter

EXCELL PRECISION CO., LTD.
ZSME200000060
16
03005XXX/03006XXX
Previous setting
3-1 External Function Setting
Press MC key
Enter parameter 00~13
After entering parameter
00, press MC key to
return to previous level
If is set as (OIML & NTEP approval), the parameter of ~cannot
be modified.
3-1-1 Backlight Mode Setting
Press MC key
Enter parameter 00~02
Press MC key to
save the setting
Default Setting: 02 (No backlight)
00 Backlight is always on.
01While weighing (weight is higher than 10d) or pressing any key, backlight be turned on
automatically. The backlight is turned off automatically when the scale is idle for 10
minutes. (d=division)
02No backlight.
When turning on, the backlight mode is the same as previous setting.
“Zero”track range
Accumulation ending mode
Pre-tare mode
”Beeper”output setting for quantity limit
Accumulation acceptable condition setting 1
Accumulation acceptable condition setting 2
Combination key Setting
Return to previous level
Backlight mode setting
Auto. power off setting
Stable range setting for
quantity sampling
Auto. unit weight average
A/D sampling speed
“Zero”display range

EXCELL PRECISION CO., LTD.
ZSME200000060
17
03005XXX/03006XXX
3-1-2 Auto. Power-off Setting
Press MC key and enter parameter 00~10. Then press MC key to save the setting.
Default Setting: 00; up to 10 minutes at most.
00 Auto Power-off function is off.
01~10 Scale is automatically powered off after not in use for 1~10 minutes.
Restart the scale to use again.
3-1-3 Stable Range Setting for Quantity Sampling
Press MC key and enter parameter 00~15. Then press MC key to save the setting.
Default Setting: 08; that means if deviation is within 8 counts of internal value, it is considered
as stable while in sampling
00~15: The higher value makes the sampling faster, but less accurate.
The smaller value makes the sampling slower, but more accurate.
It can’t be shifted after sampling, only when the unit weight is cleared in Brazil version.
3-1-4 Auto Average Unit Weight Setting
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 01
00 Off (Press SAMPLE key for manually update unit weight)
01 On; auto update average unit weight.
Auto updates unit weight when the measured sampling number increase greater than 10%
but less than 100% of previous sampling number.
3-1-5 A/D Sampling Speed Setting
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 00
00 Low speed is about 7.5 Hz. (Weighing reflection is slow but relatively stable)
01 Fast speed is about 15 Hz. (Weighing reflection is fast but relatively unstable)
3-1-6 Zero Display Range Setting
Press MC key and enter parameter 00~03. Then press MC key to save the setting.
Default Setting: 00 for approval (CFn = 02~04) or 01 for non-approval (CFn = 00~01)
00 Display as it is
01 Display 0, if within 1 division
02 Display 0, if within 2 divisions
03 Display 0, if within 3 divisions
It is activated only when the weight is over 1/3 full capacity. The pre-tare value must be
greater than setting. For example: If FnC 06 = 03, pre-tare > 3 divisions.
3-1-7 Zero Tracking Range Setting
Press MC key and enter parameter 00~03. Then press MC key to save the setting.
Default Setting: 00 for approval (CFn = 02~04) or 01 for non-approval (CFn = 00~01)
00 When gross weight is stable at 0 over 1 second, it could track 1/4 d. (d=division)
01 When gross weight is stable at 0 over 1 second, it could track 1/2 d.
02 When gross weight is stable at 0 over 1 second, it could track 1 d.
03 When gross weight is stable at 0 over 1 second, it could track 2 d.

EXCELL PRECISION CO., LTD.
ZSME200000060
18
03005XXX/03006XXX
3-1-8 Accumulation Ending Mode Setting
Press MC key and enter parameter 00~02. Then press MC key to save the setting.
Default Setting: 00
00 Press M+ key. Displays accumulation for 3 seconds, and return to weighing mode.
01 Press M+ key. Displays accumulation until press CE key to return to weighing mode.
02 Press M+ key. Beeper beeps once and does not display accumulation.
3-1-9 Pre-tare mode setting
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 00
00 Pre-tare only when weight display is 0
01 Pre-tare at any weight value on the display
Pre-tare value <= max weight of 1st interval or range; pre-tare value > external value set in
FnC 06.
3-1-10 “Beeper” Output Setting for Quantity Limit
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 00 for approval (CFn = 02~04) or 01 for non-approval (CFn = 00~01)
00 Beeper beeps when stable and quantity exceeds quantity setting (or weight exceeds
weight setting)
01 Beeper beeps when quantity exceeds quantity setting (or weight exceeds weight setting),
regardless if it is stable
3-1-11 Accumulation Acceptable Condition Setting 1
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 00
00 Accumulate only when stable.
01 Accumulate regardless if it stable.
3-1-12 Accumulation Acceptable Condition Setting 2
Press MC key and enter parameter 00~04. Then press MC key to save the setting.
Default Setting: 00
00 Accumulate only when weight is within zero band (close to 0) first. Refer rS1 07 for zero
band setting (00~99)
01 Accumulate with no need to return to zero. That means when no weight on platter, the
weight can be accumulated continuously.
02 Accumulate only when weight is within zero band of gross weight (close to gross = 0)
first. Refer rS1 07 for zero band setting (00~99)
03 Press M+ key not to accumulate the value, but RS-232 transmits the data.
04 Accumulate only when weight return to within 1/4d of gross weight first.
3-1-13 Combination Key Setting
Combination key represents kg/lb key or UNIT WEIGHT PRESET key. This key contains 2
functions: Unit switching 50 sets for unit weight preset
Press MC key and enter parameter 00~01. Then press MC key to save the setting.
Default Setting: 00
00 Press the combination key once to select unit (priority function).
Press the combination key for 3 seconds to preset unit weight (minority function).
01 Press the combination key once to preset unit weight (priority function).
Press the combination key for 3 seconds to select unit (minority function).