Ravean Heat C6 User manual

OPERATING MANUALS
FOR 5V, 9V, & 12V SYSTEMS
IMPORTANT SAFETY INFORMATION.
READ BEFORE USE. DO NOT DESTROY.

32
1
USB to Mini USB
connector included
for charging
2
NOTE:
CONTROLLER BUTTON
IS INSIDE THE LEFT
JACKET PANEL
3 4
1
1. CONTROL BUTTON
2. USB POWER CABLE PORT
3. USB POWER CABLE
4. BATTERY POCKET
2
3
1
POWER STRIP LEVEL INDICATOR
MINI USB CONNECTOR FOR CHARGING BATTERY
2A OUTPUT USB SOCKET
For full manuals go to ravean.com/manuals
RAVEANHEAT™C6 SYSTEM : 5V QUICK SETUP GUIDE
CHECK BATTERY POWER
Grab your Ravean battery and locate the 2A output USB
socket. Make sure the battery is fully charged by shaking
it side to side, the power strip will light up blue.
CONNECTING BATTERY
Once your Ravean 5V battery is fully charged, plug the
5V USB power cord into the 5V USB output port. Then
place it in the battery pocket.
JACKET QUICK START
Press and hold the controller button until the LED light
located on the button lights up. Once the LED light is
on, your garment will immediately begin warming you.
1. CONTROLLER BUTTON
TURNING ON JACKET: Press and hold controller button for 1-2 seconds to
turn on. The button will light up and pulse red as it preheats (about 5
minutes). Then it will automatically adjust to medium heat (white led light).
HIGH HEAT (RED LED): To place your jacket on high heat, press button once
after it turns on. The light will go solid red.
MEDIUM (WHITE LED): To place your heated jacket on medium heat, press
button twice after it turns on. The light will go solid white.
LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the
control button three times after it turns on. The light will go solid blue.
NOTE: You can cycle through the various heat settings by continuing to
press the button.
TURNING OFF JACKET: To turn off, press and hold at any temperature
setting, until LED light turns off.

54
RAVEANHEAT™C6 SYSTEM : 9V QUICK SETUP GUIDE
1 2
1. CONTROLLER BUTTON
2. 9V USB OUTPUT PORT
3. 9V POWER CORD
4. BATTERY POCKET
3
3
1
4
1
For full manuals go to ravean.com/manuals
12V OUTLET PORT
LED POWER INDICATOR
POWER LEVEL BUTTON 12.6V INLET PORT
QC 2.0 USB 5V/9V
OUTLET PORT
CHECK BATTERY POWER
Before using your heated product, make sure your
battery is fully charged. To do this, push the power level
button on your battery. When the battery is fully charged,
all four LED lights on the LED Power Indicator will light up
(see battery manual for charging unstructions).
CONNECTING BATTERY
Once your Ravean 12V battery is fully charged, plug the
9V USB power cord into the 9V USB output port.Then
place it in the battery pocket.
NOTE: if you are using a non-Ravean battery the light on the USB
connector will turn solid once it confirms you are using a 9v 2 amp
QC 2.0 battery. If the battery is not compatible it will continue to blink.
NOTE: CONTROLLER BUTTON IS
INSIDE THE LEFT JACKET PANEL
JACKET QUICK START
Press and hold the controller button until the LED light
located on the button lights up. Once the LED light is
on, your garment will immediately begin warming you.
1. CONTROLLER BUTTON
TURNING ON JACKET: Press and hold controller button for 1-2 seconds to
turn on. The button will light up and pulse red as it preheats (about 5
minutes). Then it will automatically adjust to medium heat (white led light).
HIGH HEAT (RED LED): To place your jacket on high heat, press button once
after it turns on. The light will go solid red.
MEDIUM (WHITE LED): To place your heated jacket on medium heat, press
button twice after it turns on. The light will go solid white.
LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the
control button three times after it turns on. The light will go solid blue.
NOTE: You can cycle through the various heat settings by continuing to
press the button.
TURNING OFF JACKET: To turn off, press and hold at any temperature
setting until LED light turns off.
2

76
RAVEANHEAT™C6 SYSTEM : 12V THREE BUTTON QUICK SETUP GUIDE
CHECK BATTERY POWER
Before using your heated product, make sure your
battery is fully charged. To do this, push the power level
button on your battery. When the battery is fully charged,
all four LED lights on the LED Power Indicator will light up
(see battery manual for charging unstructions).
1CONNECTING BATTERY
Once your Ravean 12V battery is fully charged, plug
the 12v power cord into the 12v output port. Then
place it in the battery pocket.
2
1. CONTROLLER BUTTONS
2. 12V OUTPUT POWER PORT
NOTE: CONTROLLER BUTTONS ARE
INSIDE THE LEFT JACKET PANEL
3. 12V POWER CORD
4. BATTERY POCKET
JACKET QUICK START
Press and hold the controller buttons until the LED
light located on the button lights up. Once the LED
light is on, your garment will immediately begin
warming you.
3
1
4
1. CONTROLLER BUTTONS
TURNING ON JACKET: Press and hold any of the controller buttons for 1-2
seconds to turn on. The button will light up and pulse red as it preheats
(about 5 minutes). Then it will automatically adjust to medium heat
(white led light).
HIGH HEAT (RED LED): To place your jacket on high heat, press button once
after it turns on. The light will go solid red.
MEDIUM (WHITE LED): To place your heated jacket on medium heat, press
button twice after it turns on. The light will go solid white.
LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the
control button three times after it turns on. The light will go solid blue.
NOTE: You can cycle through the various heat settings by continuing to
press the button.
TURNING OFF JACKET: To turn off, press and hold at any
temperature setting until LED light turns off.
12V OUTLET PORT
LED POWER INDICATOR
POWER LEVEL BUTTON 12.6V INLET PORT
QC 2.0 USB 5V/9V
OUTLET PORT
2
For full manuals go to ravean.com/manuals
1
3

9
RAVEANHEAT™C6 SYSTEM : 12V QUICK SINGLE BUTTON SETUP GUIDE
CHECK BATTERY POWER
Before using your heated product, make sure your
battery is fully charged. To do this, push the power level
button on your battery. When the battery is fully charged,
all four LED lights on the LED Power Indicator will light up
(see battery manual for charging unstructions).
1CONNECTING BATTERY
Once your Ravean 12V battery is fully charged, plug
the 12v power cord into the 12v output port. Then
place it in the battery pocket.
2
1. CONTROLLER BUTTONS
2. 12V OUTPUT POWER PORT
NOTE: CONTROLLER BUTTONS ARE
INSIDE THE LEFT JACKET PANEL
3. 12V POWER CORD
4. BATTERY POCKET
JACKET QUICK START
Press and hold the controller buttons until the LED
light located on the button lights up. Once the LED
light is on, your garment will immediately begin
warming you.
3
1
4
1. CONTROLLER BUTTONS
TURNING ON JACKET: Press and hold any of the controller buttons for 1-2
seconds to turn on. The button will light up and pulse red as it preheats
(about 5 minutes). Then it will automatically adjust to medium heat
(white led light).
HIGH HEAT (RED LED): To place your jacket on high heat, press button once
after it turns on. The light will go solid red.
MEDIUM (WHITE LED): To place your heated jacket on medium heat, press
button twice after it turns on. The light will go solid white.
LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the
control button three times after it turns on. The light will go solid blue.
NOTE: You can cycle through the various heat settings by continuing to
press the button.
TURNING OFF JACKET: To turn off, press and hold at any
temperature setting until LED light turns off.
12V OUTLET PORT
LED POWER INDICATOR
POWER LEVEL BUTTON 12.6V INLET PORT
USB OUTLET PORT
21
For full manuals go to ravean.com/manuals
1
3

1110
HEATED PRODUCT WARNINGS AND SAFEGUARDS
Please read the product label and all of the instructions
before using your heated product. As with all electrical
products, misuse of your heated product and/or
failure to properly follow the instructions may cause
overheating, fire, personal injury, or death.
INSTRUCTIONS FOR USE
1. If you have a medical condition which makes you
sensitive to overheating or you use any personal
medical devices, ask your physician to determine if
use of this product is appropriate.
DO NOT use your heated product on:
• An infant or young child
• An incapacitated or immobile person
• A paraplegic or quadriplegic
• A diabetic
• Anyone insensitive to heat, such as a person with
poor blood circulation
• Anyone who cannot clearly understand the
instructions and/or operate controls
2. DO NOT use if inner liner is wet. Water will increase
the risk of electric shock.
3. DO NOT abuse the power cable. Never use the cord
for carrying, pulling, or unplugging the heated
jacket. Keep cord away from heat, oil, sharp edges,
or moving parts.
4. DO NOT use the heated jacket if the power indicator
button on the battery isn’t working.
5. DO NOT allow heating elements to touch bare skin.
6. DO NOT allow the cords to be pinched.
7. DO NOT use pins. They may damage the electric wiring.
8. If the heated jacket turns off unexpectedly, check
connections and make sure your battery pack is charged.
9. SHUT OFF power immediately if any discomfort occurs.
10.ALWAYS REMOVE BATTERY PACK before changing
or removing accessories. Only use accessories
specifically recommended for this jacket. Others may
be hazardous. For a complete listing of accessories for
your Ravean jacket go online to ravean.com.
11.If the heated jacket does not start or operate
properly with a fully charged battery pack, clean the
contacts on the battery pack. If the heated jacket
still does not work properly, contact Ravean at
[email protected]
12.NEVER disassemble the heated jacket, battery,
or charger.
13.Your jacket may be safely used at temperatures
between 4°F and 140°F (-20°C and 60°C).
Use the heated jacket in accordance with these
instructions, taking into account the working conditions
and the work to be performed. Use of the heated jacket
for operations different from those intended could
result in a hazardous situation.
BATTERY WARNINGS AND SAFEGUARDS
Rechargeable lithium-ion batteries are potentially
hazardous and can present a serious FIRE HAZARD if
damaged, defective, or improperly used.
1. DO NOT try to heat the product and charge the
battery at the same time.
2. DO NOT charge battery inside battery pocket.
3. DO NOT try to disassemble or cut battery.
4. DO NOT expose to high heat or direct sunlight for
long periods of time.
5. DO NOT burn or incinerate battery.
6. DO NOT use if battery case is cracked or damaged.
7. DO NOT use if there is leakage or case bulges.
8. DO NOT use battery with any non-Ravean 12v chargers.
9. DO NOT expose battery to any type of liquid.
10.DO NOT charge at temperatures below 40°F (4°C).
11.DO NOT store at temperatures higher than 170°F (76°C).
This can potentially result in self-combustion.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, seek medical
help. Liquid ejected from the battery may cause irritation
or burns. If you see your heated product or battery is
operating improperly, unplug it immediately and contact
Ravean at [email protected]
HEATED JACKET STORAGE AND CARE
1. Disconnect the battery pack from the heated jacket
before storing. This prevents you from accidentally
turning on the jacket.
2. Batteries should be stored at temperatures between 40°F
and 80°F (4°C and 27°C) for maximum life and safety.
3. For maximum life, batteries should be stored at
40% to 70% charge.
4. Batteries in long-term storage at room temperature
should receive a charge every three months or so.
5. DO NOT leave the battery in the jacket overnight or
while not in use.
6. Maintain heated jacket. Check for breakage of parts
and any other condition that may affect the heated
jacket’s operation. If damaged, contact Ravean at
[email protected].
7. Recharge only with the Ravean charger. A charger that
is suitable for one type of battery pack may create a
risk of fire when used with another battery pack.
8. Use heated jacket only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
9. When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
10.Before washing, disconnect and remove battery
pack from jacket. Push the power cord completely
into the battery pocket and fasten closed.
11.NEVER immerse your battery holder, battery pack, or
charger in liquid or allow any liquid to flow inside them.
12.Maintain labels; they carry important information.
If labels are unreadable or missing, contact Ravean
for free replacement.
CHARGING INSTRUCTIONS
The following recommendations, in addition to the
precautions above, should be followed when charging
lithium-ion batteries to ensure the avoidance of
potentially catastrophic fire or explosion.
1. Charging should be performed in a firesafe area,
away from children or pets. NEVER charge batteries
unattended, for longer than 3-hours, or where objects
such as carpet, furniture, wood or vinyl floors, curtains,
or other flammable objects are present.
2. Charging should be performed at a temperature
between 40°F and 110°F (4°C and 43°C). Never
charge below 40°F (4°C).
1. USB POWER CORD
2. MOBILE DEVICE
3. HAND POCKET
4. MEDIA HOLE
1. BATTERY POCKET
2. USB OUTPUT
3. BATTERY POCKET MEDIA HOLE
4. CORD CHANNEL
5. HAND POCKET MEDIA HOLE
RAVEAN 12V MOBILE CHARGING
1 3 4 5
2
1
34
1
2
2
STEP 1
Plug your mobile device's
USB power cord into your
mobile device. Then, thread
the USB cord through the
media hole found inside the
jacket pocket.
STEP 2
Feed the USB cable through
cord channel inside the jacket
and into the media hole on the
battery pocket. Plug the USB
cord into the USB output on the
battery. Replace the battery
into the battery pocket.

1312
RAVEAN LIMITED WARRANTY POLICY & GUIDELINES
Ravean stands behind the quality of everything we sell,
and we hope you’re happy with your heated product. If you
encounter any problems with the operation of our products,
or you would like to give us feedback on our jackets, please
contact us through our website at ravean.com
The Ravean products are warranted to the original
owners against manufacturing defects in materials and
workmanship for 90 days. It does not cover normal wear
and tear. Wear and tear is damage that naturally and
inevitably occurs as a result of normal use. Regardless
of how carefully you use or how well you care for your
Ravean jacket, it will eventually begin to show age and
wear. Common examples of wear and tear that would
not be covered under the warranty include colors fading,
abrasions on the bottom of battery packs or at the
cuffs/pockets from rubbing when you walk, and general
breakdown of the materials over the years.
Only original, unaltered, and unmodified materials and
workmanship are covered by this policy. This warranty
does not cover damage caused by accident, improper
care, negligence, normal wear and tear, or the natural
breakdown of colors and materials over extended time
and use.
To return a Ravean item for warranty evaluation, you
will need a Return Authorization number (RA number),
which can only be obtained directly from the Ravean
Warranty Department. To initiate the warranty process,
please send an email to [e-mail].
Please include the following in your email:
• Full name and email address associated with the order
• Detailed description of the issue you are experiencing
The Ravean Warranty Department will help resolve
the issue and give you an RA number with further
instruction. If necessary, we will have you send the
jacket into us for evaluation. All costs for shipping and
insuring products sent in for evaluation must be prepaid
by the customer. No return shipping labels are provided.
Any COD will be refused and fees incurred by the
customer. Any product that is returned without an RA
number will be returned unopened
Ravean is not liable for lost in-bound packages. Utah
state law requires that products accepted for repair
must be clean. Charges will be assessed if cleaning is
necessary, and the heated jacket may be returned to you
if it cannot be adequately cleaned.
This warranty is available worldwide.
This warranty gives you specific legal rights; you may
have other rights, which vary from state to state.
RAVEAN LIABILITY
Ravean will not be liable for any incidental or
consequential damages caused by the breach of any
express, implied, or statutory warranty or condition.
Except to the extent prohibited by applicable law, any
implied warranty or condition of merchantability or
fitness for a particular purpose is limited in duration to
the duration of the above warranty.
Ravean disclaims all other warranties, conditions
or representations, express, implied, statutory, or
otherwise. Ravean shall not be liable for any damages
of any kind resulting from the purchase, use or misuse
of, or inability to use the heated product including
incidental, special, consequential or similar damages
or loss of profits, or for any breach of contract,
fundamental or otherwise, or for any claim brought
against purchaser by any other party. Some provinces,
states, or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so
the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you
may also have other rights that vary from province to
province, state to state, or jurisdiction to jurisdiction.
For questions or support, please visit ravean.com or
email at [email protected]
FCC Notification: This equipment has been tested
and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following:
- Reorient or relocate the receiving antenna;
- Increase the separation between the equipment and
receiver;
- Connect the equipment into an outlet on a circuit
different from that to which the
receiver is connected;
- Consult the dealer or an experienced
radio/TV technician for help.
In accordance with the rules and regulations of the
FCC, changes or modifications to this equipment, not
expressly approved in writing by Ravean™could void the
user’s authority to operate this equipment.
For questions or support, please visit
ravean.com
PLEASE DO NOT RETURN THIS PRODUCT TO
PLACE OF PURCHASE.
© 2017 Duralogic USA LLC. Doing business as Ravean.
All rights reserved.
Distributed by Ravean
3. DO NOT attempt to charge a battery that is swollen or bulging.
4. USE ONLY supplied charging cables and connections.
Make sure connections are in good condition.
5. DO NOT allow the charging polarity to be reversed or
short-circuited.
6. Observe the battery in a safe place for at least 15
minutes after charging is complete, as a delayed
chemical reaction can occur if a fault is present.
7. A healthy battery should only get slightly warm
during charging. If the battery becomes hot, smokes,
swells, or gives off an odor during charging,
terminate charging immediately and contact the
Ravean support.
NOTE: the charger itself may get quite warm to the
touch when charging a deeply discharged battery.
A FIRE IS MOST LIKELY TO OCCUR DURING THE
CHARGING PROCESS UNDER THE FOLLOWING
CIRCUMSTANCES:
1. THE BATTERY HAS BEEN FULLY DISCHARGED AND
IS NOT RECHARGED SHORTLY AFTERWARD. This
potential is aggravated if batteries are damaged,
contain an undetected factory defect, are used or
stored at temperature extremes, or are approaching
the end of their useful life. Ideally, batteries should
be recharged within 24 hours of a full discharge.
2. CHARGING IS ATTEMPTED AT TEMPERATURES
BELOW 40°F (4°C). Charging below 40°F (4°C),
causes a chemical reaction in the battery cells that
can cause permanent damage and the possibility of
fire or explosion during charging.
3. THE BATTERY HAS BEEN EXPOSED TO LIQUIDS,
ESPECIALLY SALTWATER. Exposure to liquids can
cause internal corrosion or damage to the cells or to the
Battery Management System (BMS). The BMS protects
the battery from overcharging, high self-discharge,
or imbalanced charging of the cells, any of which can
present the possibility of fire during recharging.
4. OPERATING OR CHARGING A BATTERY OR BATTERY
CHARGER THAT HAS BEEN DAMAGED from dropping
or from shipping damage, or damaged in any way. A
damaged battery is subject to explosion or fire. Properly
dispose of a dropped or damaged battery immediately.
5. USING A CHARGER OTHER THAN THE ONE
SPECIFICALLY DESIGNATED FOR THE BATTERY BY
RAVEAN. A charger that is suitable for one type of
battery pack may create risk of fire when used with
another battery pack.
SAFE DISPOSAL OF LITHIUM-ION BATTERIES
Lithium-ion batteries contain elements that may pose
health risks to individuals. If not disposed of properly,
they can leach into the groundwater supply. In some
countries, it may be illegal to dispose of these batteries
in standard household waste.
Fortunately, many recycling facilities exist that process
lithium-ion batteries, in part due to the value of the
materials contained within the individual cells. In the
United States and Canada, a large network of over
30,000 battery drop-off locations may be found at
www.call2recycle.org.
To render the battery safe, apply tape over any exposed
connectors to prevent the accidental shorting of the positive
and negative terminals of the battery during transport.
Place each battery into its own plastic bag, seal the bag, and
deposit the battery into the recycling container.
NEVER dispose of the battery in a fire or incinerator, as
the battery may catch fire and explode.
WASHING AND SPOT CLEANING
If your down jacket gets a few areas of light dirt or other
substances, you don’t need to wash the whole thing. Use
a small drop of liquid detergent and lightly scrub the
affected area with a wet towel until clean.
WASHING YOUR DOWN JACKET
1. Before washing, disconnect and remove battery
pack from jacket. Push the power cord completely
into the battery pocket and fasten closed.
2. Use a small amount of stain remover or down wash
to treat any really dirty spots.
3. Place your jacket in the washing machine on delicate
cycle, set to cold (not hot or warm), and add the
down wash as directed.
4. Dry on the lowest heat setting on your dryer. If
desired, you can throw in three clean tennis balls
to help break up wet clumps of down. If you don’t
have any tennis balls, you can put shoes inside clean
socks or make sock balls as a substitute. The drying
process will be slow, but it’s the most important part.
Be patient. The jacket will usually take around 2-3
hours to dry.
5. Make sure your jacket is completely dry before packing
or compressing it. Compressing wet down can hurt the
insulation properties and cause mold to form.
6. Always store your down jacket uncompressed in a
clean and dry spot.
HAND WASH INSTRUCTIONS
1. Mix 1 tsp (5mL) vinegar into cold water then place
the garment in water for 5-10 minutes. Use a soft
brush to remove dirt. DO NOT rub the garment.
2. Squeeze the water out of garment. Do not wring.
3. Use clean water to rinse away remaining detergent.
1. Wrap a clean, dry towel around the garment and
squeeze out any remaining moisture.
2. Let air-dry on a flat, clean surface or hang on a
plastic hanger. Avoid exposure to sun.
3. DO NOT IRON.
4. Once the garment is dry, flap it up and down several
times to fluff the down. Always store your down
jackets uncompressed in a clean and dry spot.
MACHINE WASH, GENTLE
CYCLE IN COLD WATER
DO NOT BLEACH
DO NOT WRING OUT OR TWIST
TUMBLE DRY, LOW HEAT
DO NOT IRON
DO NOT DRY CLEAN

14
Designed in Utah | Made in China
ravean.com/manuals
RUM-2017