Ravenheat RSF 84ET User manual

USER’S GUIDE
HIGH EFFICIENT COMBINATION BOILER
RSF 84ET - RSF 84E - RSF 100ET - RSF 100E
WITH OR WITHOUT BUILT IN TIMER
It is the law that all gas appliances are installed by
a competent person, in accordance with the gas
safety installation and use current regulations.
To the current Gas Safety (Installation and Use)
Regulations “1996”
All CORGI registered installers carry a CORGI I.D.
card and have a registration number. Both should be
recorded in your boiler log book. You can check your
installer by calling CORGI direct on: 01256 732300.
Escape of gas
Should a gas leak be suspected, contact your gas
supplier without delay.
Do NOT search for gas leaks with a naked flame.
WARNING: This appliance must be earthed.
Do not touch or tamper with this sealed unit or
its components
1.
1.1
INTRODUCTION
Please carefully read information given in
the booklet to help you gain maximum con-
trol from your appliance with minimum
trouble and cost.
1.1.1
Your Ravenheat Combination Boiler has
been designed to supply your Central
Heating and Domestic Hot Water directly
from one unit.
When central Heating is operating, the cir-
culation will be interrupted when domestic
hot water is being drawn off. This will nor-
mally not affect the level of heating.
1.2.1
1.4.2
1.4.3
CLEARANCES AROUNDTHE BOILER
RSF 84E(T)
RSF 100E(T)
Above
125 mm 150 mm
Below 100 mm 100 mm
Front 450 mm 450 mm
Sides 75 mm
5mm
25mm in front when installed in a cupboard.
Minimum clearances are required for safety
and maintenance. Do not obstruct any pur-
pose made ventilation opening if boiler has
been fitted in a compartment.
Never hang clothes, etc., over the appliance.
USER CONTROLS
See Fig. 1
This appliance is designed to operate with the
minimum of attention by the user. All controls
are to be found on the control panel.
OPERATING SAFETY CHECKS TO
PROTECTYOUR APPLIANCE
Before lighting the appliance check central
heating system pressure (7) is not less than 1
bar gauge. If it is below this do not light but
consult your installer about refilling your sys-
tem as you may have a leak in the system.
An ORANGE warning light on the control pan-
el (8) warns of a flame failure of the main
burner. This can be reset manually by press-
ing mains boiler on/off switch (1).
A RED warning light on the control panel (9)
warns of a high temperature lockout on the
overheat thermostat. This could occur due to air
or poor circulation in the boiler/heating circuit,
This can be reset manually by removing grey
cover (3) on control panel and pressing red re-
set button. Replace cap. If lockout should per-
sist leave the appliance shut down and consult
your installer/service engineer immediately.

2.
OPERATING DOMESTIC HOT WATER 3.3 TO SHUT DOWN THE APPLIANCE
2.0
Select only switch position (1).
2.1 Open hot water tap. After about 3 seconds
main burner will always operate.
2.2
Temperature of domestic hot water can be
varied by adjusting the water flow rate at the
tap. Domestic thermostat (5) will control maxi-
mum temperature leaving the appliance.
The knob can be set between minimum and
maximum approximately 35
o
C to 65
o
C (95F
to 149F). For maximum temperature of do-
mestic hot water leave in maximum position.
3.
OPERATING HEATING & HOT WATER
TO SET AND ADJUST BUILT-IN TIMER
MODEL SEE OPPOSITE PAGE 3.
3.0
Select switch (2) position.
3.1
Switch on time clock, adjust room stat and/or
thermostatic radiator valves to high settings.
3.2 Main burner will operate. Temperature output
of central heating can be adjusted by central
heating thermostat (4). The knob can be set
between minimum and maximum approxi-
mately 40
o
C to 85
o
C (140F to 185F). While
the appliance is being used to provide domes-
tic hot water, the central heating will not oper-
ate. When hot water is no longer required the
appliance will automatically revert to central
heating and should not noticeably affect the
level of central heating. Adjust external con-
trols to required settings.
NOTE: An anti-cycling device is fitted to
the heating function. When the boiler
reaches its set maximum temperature it
will not operate on heating for about 3 min-
utes but the domestic hot water function
will always operate on demand.
3.3.1 For short periods, switch to only and turn
off all hot taps. For long periods switch of the
on/off switch (1). If the appliance is to be shut
down for long periods when there is a risk of
freezing, then appliance should be drained.
Similar refilling must be done by a competent
person following approved procedures.
4.
4.1
CLEANING OF APPLIANCE OUTER CASING
Use a clean damp cloth. Do not use any
abrasive cleaners end with a dry cloth lightly
polish to protect painted surfaces.
Control panel and fixtures can be wiped with
damp cloth and dried. Spray polishes must
not be used on control panel surfaces or
switches, Care must be taken in preventing
any liquids entering the appliance.
4.2
CARE OF YOUR APPLIANCE
AND SYSTEM
4 2.1
Annual servicing of your appliance is required
to maintain safety and efficiency of its opera-
tion.Therefore it is recommended that the ap-
pliance is serviced at least once a year and
that the whole of the heating system be
checked at the same time by a qualified in-
staller. If it is known or suspected that a fault
exists on the boiler then it MUST NOT be
used until the fault has been corrected by a
COMPETENT PERSON. It is essential that
the instructions in this booklet are strictly fol-
lowed for safe and economic operation of the
boiler.
SERVICING SHOULD BE CARRIED OUT BY A
QUALIFIED INSTALLER.
Ravenheat Manufacturing Ltd.,
Chartists Way, Morley, Leeds LS27 9ET.

PROGRAMMABLE TIMECLOCK
lNSTRUCTIONS FOR USE
Your Ravenheat boiler comes complete with (optional)
digital programmer. The timeclock is supplied with a
cover to prevent accidental loss of programme, or
children tampering with preset programmes.
5.
TO PROGRAMME TIME CLOCK
To access programming buttons remove clear cover.
Press reset key with a pencil before setting or
reprogramming times.
5.1.1
TO SET TIME AND DAY OF THE WEEK:
5.1.1.1
SET DAY OF WEEK:
- Press clock button and hold in.
Press day button to desired day.
- Release both buttons.
The day of the week will be set.
5.1.1.2 SET HOUR:
- Press clock button and hold in.
Press hour button to desired time.
- Release both buttons.
The hour will be set.
5.1.1.3 SET MINUTE:
- Press clock button and hold in.
Press minute button to desired time.
- Release both buttons.
The minute will be set.
NOTE: When, setting time holding in the hour/minute
button this will rapidly advance the display.
5.1.2
TO SET PROGRAMMES:
5.1.2.1
Press timer button and release to enter into
programme mode.
5.1.2.2
Programme “1 ON” will show in lower left
hand corner.
5.1.2.3
Press DAY key to select the programme period.
There are 10 day settings for your choice.
(1) MOto Su (2) MO(3) Tu (4) We (5) Th
(6) Fr (7) Sa (8) Su (9) Mo+TucWe+Th+Fr
(10) Sa+Su.
You now have a choice of 6 programmes.
5.1.2.4 Press hour button to set the required hour ‘on’.
5.1.2.5
Press minute button to set minute.
5.1.2.6 After setting the programme press TIMER key
again “1 OFF” will appear. Repeat procedure
5.1.2.3 through to 5.1.2.5 to set programme
“1 OFF’TIME.
For each programme days ‘off’setting must be
input the same as the ‘on’ setting.
5.1.2.7 After setting programme 1 ON/OFF TIME
repeat step 2.1 to 2.7 to set programmes 2
through to 6 if required.
5.1.2.8 Your timer gives you up to 6 different ONE
and 6 different OFF settings per programme
period. Note you have a choice of 6 ON-6
OFF programmes max.
5.1.2.8.1 REVIEW YOUR PROGRAMMES:
- Press the TIMER key to advance display to
each subsequent ON or OFF setting.
- Check days and times displayed.
- To make a change, follow instructions
under “TO SET PROGRAMMES”.
Note on completion of programming operations
press the clock button to show current time/day
and replace the clear tamper proof cover.
5.1.2.8.2 MANUAL KEY
- Press MANUAL key to select ON /AUTO
OFF mode.
- ON mode is to turn on the timer, OFF
mode is to turn off the timer.
- AUTO mode is to set the timer to
programme mode. It will turn on or turn off
according to the programmes you set.
- From ON to AUTO mode it will turn on until
next OFF programme.
- From OFF to AUTO mode it will turn off
until next ON programme.
5.1.2.8.3 LED INDICATOR
LED light is on when the boiler is operating in
heating mode.
5.1.3
TO RESETTIMER:
Press reset button to reset the timer unit.
NOTE:
Once the reset button is pressed, the stored time and
programme will be cleared to initial state.
N.B.: When the clock is either “programmed” on, or is on constant, the red indicator will illuminate

Chartists Way, Morley, Leeds, LS27
Telephone: [phone]
Tfax: [phone]