Rayco FACE User manual

RAYFace
3D Scanner
Model: RFS200
User Manual
RUG-3623-EN
Rev. 1.0

This user manual contains information on the appropriate use of RAYFace.
The operator must read this manual carefully before using the product.
The operator must follow instructions and safety regulations described in the user manual to
prevent any injury to the operator and damage to the product.
Copyright Ray Co., Ltd.
Publication number: RUG-3623-EN_Rev.1.0 (Revised Sep. 01, 2022)
This manual is subject to quality upgrade and specification change without prior notice.
For further inquiries, contact customer service of manufacturer.
Manufacturer: Ray Co., Ltd.
332-7, Samsung 1-ro, Hwaseong-si, Gyeonggi-do, 18380, Korea
Phone: [phone] FAX: [phone]
Customer Service: [phone]
www.raymedical.com

RAYFace Contents
Contents
User Manual Introduction ................................................................................6
Related Terms ............................................................................................................6
Symbols .....................................................................................................................6
Safety Information ......................................................................................................7
System Symbols.........................................................................................................7
Precautions for Installation .........................................................................................8
Precautions for Use ....................................................................................................9
Precautions for Power Connection..............................................................................9
Precautions for Cleaning the Product .......................................................................11
Label ........................................................................................................................ 11
Product Introduction ...................................................................................... 13
Usage.......................................................................................................................13
Intended use.............................................................................................................13
Components .............................................................................................................13
Sections and Functions (Scanner Body)...................................................................14
Sections and Functions (Calibration Kit) ...................................................................15
Installation.......................................................................................................17
Installation Environment ...........................................................................................17
Installation Setting...........................................................................................17
Working Environment ......................................................................................18
System Requirements ..............................................................................................19
Maintenance.............................................................................................................20
Maintenance ...................................................................................................20
Product Installation...................................................................................................21
Fix both left and right arms of main body .........................................................21
Connect Power................................................................................................22
Power On and Off............................................................................................23
Connect to Network.........................................................................................23
Network Setting Configuration.........................................................................24
Connect to PC.................................................................................................25
Assemble Calibration Kit .................................................................................26
Proceed with Calibration .................................................................................27

RAYFace Contents
Software Installation .................................................................................................28
RAYFace Screen Composition..................................................................................30
Register Scanner......................................................................................................31
Server Registration...................................................................................................34
RAYScan Server Registration..........................................................................34
RAYFace Server Registration..........................................................................37
Linked Program Registration ....................................................................................39
Operating Software......................................................................................... 42
Register Subject .......................................................................................................42
Capture ....................................................................................................................43
Capture ...........................................................................................................43
Capture Options ..............................................................................................46
Captured Data Management.....................................................................................50
Validate Captured Data ...................................................................................50
Unreconstructed Data Management ................................................................52
Reconstructed Data Management ...................................................................54
Move Captured Data .......................................................................................58
Export Captured Data......................................................................................59
Import Captured Data......................................................................................61
Deleted Data Management..............................................................................64
Settings ....................................................................................................................66
General Settings .............................................................................................66
Device Settings ...............................................................................................74
Status Indicator ..............................................................................................80
RAYFace Indication ..................................................................................................80
Appendix A. Product Specifications.................................................................. 81
Appendix B. Messages .......................................................................................82
Appendix C. Regulations ....................................................................................90

RAYFace 1. Introduction
5
Introduction
1

RAYFace 1. Introduction
6
User Manual Introduction
The following user manual contains not only a specific step-by-step guide on how to use RAYFace
(referred to as “the product”), but also the basic information regarding the product.
1) Please keep this manual for future reference.
2) Please read the safety regulations before using the product.
3) The pictures on the user manual might differ from actual ones depending on the option
and model of the product.
4) The screenshot on the user manual might differ from actual ones depending on the
software version of the product.
Related Terms
Some terms used in this manual may be used interchangeably as follows.
1) RAYFace is a software to operate RAYFace.
2) “Scanner” refers to the main body of RAYFace.
3) Left scanner, center scanner, and right scanner refers to the 3 cameras of RAYFace.
Symbols
Indicates a hazardous situation that, if the instructions are not followed, could
result in death or serious injury.
Indicates a hazardous situation that, if the instructions are not followed, could
result in minor or moderate injury.
Indicates information considered important but not hazardous.

RAYFace 1. Introduction
7
Safety Information
The following safety information must be read and understood before using the product. Please
check the safety precautions to use it safely and correctly. Improper use of the product may cause
bodily injury or death.
The owner of the product must ensure that all precautions, safety measures and
maintenance procedures are performed.
Use only genuine parts approved or provided by the manufacturer in this product.
Service and repairs due to equipment failure caused by not using genuine
products are not covered under the warranty.
Do not modify or alter the device unless authorized by the manufacturer.
System Symbols
The symbols used in the device.
CE Mark.
UL Mark.
RCM Mark.
Power symbol.
Device serial number.
The symbol indicates that the product may include industrial waste materials.
Do not look into the beam. (This product is classified as Risk Group 2 (RG2) of
IEC 62471-5).

RAYFace 1. Introduction
8
Precautions for Installation
Risk of electric shock or fire
▪Do not install the product in humid or dusty place or where moisture can accumulate.
▪Do not put candles, lighters, etc. on the product or install the product near heating
appliance.
▪Do not use the product near flammable sprayer or substances.
▪Do not install the power cord where it is difficult to remove.
Risk of malfuction, equipment failure, or bodily injury
▪Install the product on a safe and flat surface with no risk of falling.
▪Do not install the product in a place exposed to direct sunlight or ultraviolet (UV) light.
▪Do not install the product where vibration or strong shock might occur.
▪Install the product in a place that meets the operating temperature conditions.
▪Use the product at temperature between 10°C to 35°C / 50°F to 95°F.
▪Install the product in a well-ventilated area to allow heat release from the product for
cooling.
▪Do not install near an object that generates a magnetic field such as motor.
▪Do not turn the product upside down or lay it down when moving.
▪Remove the power cord after pressing the power button to turn it off when moving.
▪Do not install in a place where there is a strong light directly to the front of the product.
▪Do not install in a place where there is a strong light directly to the subject's face or
background.
▪Install where there is a normal white fluorescent light or LED light.
▪When installing near a window, cover the window with blinds or curtains.

RAYFace 1. Introduction
9
▪Install it 10cm away from the end of the table.
Leaving a BATTERY in an extremely high temperature surrounding environment
can result in an EXPLOSION or the leakage of flammable liquid or gas.
A BATTERY subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
Risk of fire or explosion if the battery is replaced by an incorrect type. Dispose of
used Batteries according to the instructions.
▪Use appropriate for the Storage environment and Operation environment conditions of
the product.
Precautions for Use
Risk of malfuction, equipment failure, or bodily injury
▪Do not place heavy objects on top of the product.
▪Do not disconnect the power cord during operation.
▪If used in a manner not specified by the manufacturer, the protection function may be
impaired.
▪The recommended illuminance level for the subject location is 500 ~ 1,500 Lux.
▪Do not look into the beam. This product is classified as Risk Group 2 (RG2) of IEC
62471-5.
Precautions for Power Connection
Risk of electric shock or fire
▪Do not use loose power outlets or damaged power cord.
▪Do not touch the power cord with wet hands.
▪Grasp the power cord and pull to disconnect, and avoid pulling out of the cable line.
▪Remove the power cord during a thunderstorm.

RAYFace 1. Introduction
10
▪Do not place objects (chemicals, water containers, and little metallic objects such as
tweezers) near the product.
▪Remove the power cord if the product emits strange sound, smell, or smoke and contact
the seller.
▪Use with a rated voltage.
▪Use an outlet (or multi-outlet) with a ground terminal that meets the rated
voltage/current.
▪Do not bend excessively or damage the power cord.
▪Remove the power cord when the product is not in use for an extended period of time.

RAYFace 1. Introduction
11
Precautions for Cleaning the Product
Risk of electric shock or fire
▪Remove the power cord when cleaning the product.
▪Use soft, lint-free cloth when cleaning. Soak it with a little bit of water to clean the
product, and be careful not to get water on the inside.
▪Use after removing any dust or water from the power cord pin.
▪Do not use thinner, alcohol, benzene, or other chemcial products to clean the product.
Color or outer appearance of the product can be altered due to chemicals.
Label
The location of the label and mark on the product.

RAYFace 2. Product Introduction
12
Product
Introduction
2

RAYFace 2. Product Introduction
13
Product Introduction
Usage
RAYFace is a scanner that uses the onboard cameras to scan images of the subject’s face in all
directions simultaneously and reconstruct the scanned data to create a 3D model. The 3D face
data obtained from RAYFace is used for various modeling tasks.
Intended use
This product is a scanner which creates a 3D model by photographing a human face with multiple
cameras.
Components
Scanner body
AC Adapter
Power Cord
Quick Guide
Screwdriver,
Screws
Calibration body
Calibration base
LAN Cable
USB Cable
Actual components may look different from pictures shown above. Depending on
the option purchased or region, the type, quantity, and packaging of the
components provided may look different from the contents of this manual. For
inquiries regarding the components, contact Ray Customer Service or your local
distributor.

RAYFace 2. Product Introduction
14
Sections and Functions (Scanner Body)
[Front] [Rear]
Items
Description
1
Power Switch
Main power On/Off switch.
2
DC IN Port
Terminal to connect the AC adapter plug. Connect one side
of the power cord to the AC adapter before connecting to
the outlet.
Attention: The power cord type may differ depending
on the region.
Warning: Do not use other AC adapters.
3
PC Port
Port for the RAYFace setup during installation.
4
Ethernet Port (RJ45)
Port to connect an ethernet cable.
5
Status Indicator
LED to indicate the equipment status.
6
Left Camera
Camera to scan an image from the left.
7
Right Camera
Camera to scan an image from the right.
8
Bottom Camera
Camera to scan an image from the bottom.
9
Teeth Cam L
Camera to scan the left side of the teeth.
10
Teeth Cam R
Camera to scan the right side of the teeth.
11
DLP Projector
Projector to project a Scan Pattern.
12
Face Cam
Camera to scan an image from the front.
13
Left Light
LED lighting for a subject’s left side of the face.
14
Right Light
LED lighting for a subject’s right side of the face.
15
Bottom Light
LED lighting for a subject’s lower side of the face.
16
Mirror
Mirror where a subject can check his or her appearance.
17
Calibration Port
Port to connect the Calibration kit.

RAYFace 2. Product Introduction
15
Sections and Functions (Calibration Kit)
[Front] [Side] [Rear]
Item
Description
1
Face Cam Cal Pattern
Panel that calibrates the cameras, front and rear panels are
used for calibration.
2
Teeth Cam Cal Pattern
3
Main Body Port
Terminal to connect to RAYFace main body.

RAYFace 3. Installation
16
Installation
3

RAYFace 3. Installation
17
Installation
Installation Environment
Installation Setting
The product should be installed on a level surface within 1° of inclination and on a table capable of
stably supporting a weight of 44 lb(20 kg) or more and an area of 20 in x 20 in(50 cm x 50 cm) or
larger.
Remove the power cord after pressing the power button to turn the product off
when moving the device.

RAYFace 3. Installation
18
Working Environment
1) Do not install the product in a place exposed to direct sunlight or ultraviolet (UV) light.
2) Use the product at room temperature between 10°C to 35°C / 50°F to 95°F.
3) Do not install near a wireless apparatus or mobile device that generates
electromagnetic interference.
4) Do not move the product during operation.
5) Do not put the product under severe shock.
Be sure to follow installation setting and working environment. If not, scan error
and equipment damage may occur.

RAYFace 3. Installation
19
System Requirements
Desktop
Item
Minimum Requirements
Recommended Requirments
CPU
Intel Core i5-10600
Intel Core i7-10700
RAM
16GB
32GB
GPU
NVIDIA GeForce RTX 2060 6GB
NVIDIA GeForce RTX 3070 8GB
Storage
1TB SSD
1TB SSD
Monitor
1920 X 1080
1920 X 1080
USB
1 x USB port 2.0
1 x USB port 2.0
LAN
1Gbps Ethernet
1Gbps Ethernet
Operating
System
Microsoft Windows® 10 x64
Microsoft Windows® 11 x64
Microsoft Windows® 10 x64
Microsoft Windows® 11 x64
Laptop
Item
Minimum Requirements
Recommended Requirments
CPU
Intel Core i5-10500H
Intel Core i7-10800H
RAM
16GB
32GB
GPU
NVIDIA GeForce RTX 2060 6GB
NVIDIA GeForce RTX 3070 8GB
Storage
1TB SSD
1TB SSD
Monitor
1920 X 1080
1920 X 1080
USB
1 x USB port 2.0
1 x USB port 2.0
LAN
1Gbps Ethernet
1Gbps Ethernet
Operating
System
Microsoft Windows® 10 x64
Microsoft Windows® 11 x64
Microsoft Windows® 10 x64
Microsoft Windows® 11 x64

RAYFace 3. Installation
20
Maintenance
As described in the description, the user must conduct periodic maintenance. It is the user’s
responsibility to maintain the product in order to prevent potential problems.
Maintenance
A periodic maintenance will prevent degradation of image quality. Degradation of
image quality could be the result of problems such as damage in product itself.
Do not throw away the packaging after the installation. For warranty service, the
product must be brought into the service center in its original packaging.
Period
Description
Initial Installation
After initial installation, proceed with calibration by using the provided
calibration kit.
Daily
Make sure there are no foreign substance obstructing the camera lenses.
Before Scanning
Make sure the LED lighting are turned on.
Monthly
Proceed with calibration every month or when relocating the equipment.