Raymarine LightHouse Sport Assembly instructions

English (en-US)
Date: 06-2019
Document number: 81384-3
© 2019 Raymarine UK Limited
Basic operation instructions
version 3.9.98

Important information about this document
This document provides an introduction to using your Raymarine
multifunction display, covering only basic operations.
To obtain the complete “LightHouse Sport Advanced operations”
document, visit the Raymarine website. The document is available
in 2 different formats:
1. Free download (PDF format)
2. Purchase a printed manual (paperback book format)
www.raymarine.com/manuals
Download complete manual (free) Purchase complete printed manual
Tip: If you own a smartphone or tablet with a camera you can use the QR code shown
above to visit the “LightHouse SportManuals and documents" area of the website directly.
To use this code, download a free “QR barcode scanner” app from the Apple or Android
appstore and then point the camera at the QR code on this page.
English (en-US)

Trademark and patents notice
Raymarine,Tacktick,Clear Pulse,Truzoom,SeaTalk ,SeaTalk hs,SeaTalkng ,
and Micronet, are registered or claimed trademarks of Raymarine Belgium.
FLIR,LightHouse,DownVision,SideVision,RealVision,HyperVision,Dragonfly,
Element,Quantum,Axiom,Instalert,Infrared Everywhere,The World’s Sixth
Sense and ClearCruise are registered or claimed trademarks of FLIR Systems,
Inc.
All other trademarks, trade names, or company names referenced herein are
used for identification only and are the property of their respective owners.
This product is protected by patents, design patents, patents pending, or design
patents pending.
Warranty registration
To register your Raymarine product ownership, please visit www.raymarine.com
and register online.
It is important that you register your product to receive full warranty benefits.
Your unit package includes a bar code label indicating the serial number of the
unit. You will need this serial number when registering your product online. You
should retain the label for future reference.
Technical accuracy
To the best of our knowledge, the information in this document was correct at
the time it was produced. However, Raymarine cannot accept liability for any
inaccuracies or omissions it may contain. In addition, our policy of continuous
product improvement may change specifications without notice. As a result,
Raymarine cannot accept liability for any differences between the product and
this document. Please check the Raymarine website (www.raymarine.com) to
ensure you have the most up-to-date version(s) of the documentation for your
product.
Software updates
Check the Raymarine website for the latest software releases
for your product.
www.raymarine.com/software
Publication copyright
Copyright ©2019 Raymarine UK Ltd All rights reserved
English (en-US)
Document number: 81384-3
AC;16928;2019-06-27T10:19:48

Contents
Chapter 1 Important information 8
Disclaimers ............................................................................ 8
Chapter 2 Set up 9
2.1 Getting started.................................................................... 9
Display controls ..................................................................... 9
Startup wizard....................................................................... 10
First power up Limitation on Use acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuringtransducer settings................................................... 11
Identifying engines.................................................................. 12
Performing a settings or factory reset............................................. 13
2.2 Shortcuts.......................................................................... 13
2.3 Switching active app............................................................ 14
2.4 Memory card compatibility.................................................... 15
Removing MicroSD cardfrom its adaptor......................................... 15
Inserting a MicroSD card ........................................................... 16
2.5 Data sources menu............................................................. 17
Manually assigninga data source................................................. 17
2.6 EV-1 heading sensor............................................................ 18
2.7 Software updates................................................................ 18
Updating display software using a memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Updating software using an internet connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.8 User data import and export.................................................. 22
Saving user data .................................................................... 22
Importing user data................................................................. 23
Chapter 3 Homescreen 24
3.1 Homescreen overview.......................................................... 24
Available apps.......................................................................25
Assigning app pages to Quicklaunch buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.2 Customizing app pages........................................................ 27
3.3 Settings menu.................................................................... 27
3.4 Alarms.............................................................................. 29
3.5 Position settings................................................................. 30
3.6 Timer............................................................................... 31
Chapter 4 Waypoints, Routes and Tracks 32
5

4.1 Waypoints.......................................................................... 32
Placing awaypoint (Quick method)................................................ 32
Waypoint management............................................................. 33
4.2 Routes ............................................................................. 36
Creating aRoute .................................................................... 36
Route management................................................................. 37
4.3 Tracks .............................................................................. 39
Creating a track ..................................................................... 40
Track management .................................................................40
Chapter 5 Chart app 42
5.1 Chart app overview.............................................................. 42
Chart appcontrols .................................................................. 43
Selecting achart card .............................................................. 44
Chart modes......................................................................... 45
Navigation ........................................................................... 46
Autopilot command................................................................. 49
Automatic Identification System (AIS) support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
RealBathy™...........................................................................50
Chapter 6 Fishfinder app 51
6.1 Fishfinder app overview........................................................ 51
Fishfinder channels — Element™ HV displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Fishfinder channels — Element™ S displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Fishfinder app controls............................................................. 53
Placinga Waypoint in the Fishfinder app......................................... 55
Chapter 7 Dashboard app 57
7.1 Dashboard app overview....................................................... 57
Switching data page................................................................ 57
Hiding and showingdatapages................................................... 58
Navigationand sailing dials........................................................ 58
Rolling road..........................................................................59
Chapter 8 Radar app 61
8.1 Adding the Radar app icon to the homescreen......... . . . . . . . . . . . . . . . . . . 61
Pairing a Quantum™ radar scanner ................................................ 61
8.2 Opening the Radar app........................................................ 62
Putting the radarinto standby ..................................................... 64
Powering down your radar scanner............................................... 64
6

8.3 Radar modes ..................................................................... 65
8.4 Automatic Identification System (AIS) support....................... . . . . . 65
8.5 Range and bearing.............................................................. 66
8.6 Guard zone alarm ............................................................... 67
Chapter 9 Technical support 69
9.1 Raymarine product support and servicing . . . . . . . . . . . . . . . . . . . . . . ........... 69
Identify display variant and software version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Viewingproduct information....................................................... 71
9.2 Learning resources ............................................................. 73
7

8
Chapter 1: Important information
Warning: Ensure safe navigation
This product is intended only as an aid to navigation and
must never be used in preference to sound navigational
judgment. Only official government charts and notices
to mariners contain all the current information needed
for safe navigation, and the captain is responsible for
their prudent use. It is the user’s responsibility to use
official government charts, notices to mariners, caution
and proper navigational skill when operating this or any
other Raymarine product.
Disclaimers
Raymarine does not warrant that this product is error-free or that it is
compatible with products manufactured by any person or entity other
than Raymarine.
This product uses digital chart data, and electronic information from
Global Navigation Satellite Systems (GNSS) which may contain errors.
Raymarine does not warrant the accuracy of such information and you
are advised that errors in such information may cause the product to
malfunction. Raymarine is not responsible for damages or injuries
caused by your use or inability to use the product, by the interaction
of the product with products manufactured by others, or by errors in
chart data or information utilized by the product and supplied by third
parties.
This product supports electronic charts provided by third party
suppliers which may be embedded or stored on memory card. Use of
such charts is subject to the supplier’s End-User Licence Agreement.

9
Chapter 2: Set up
2 1 Getting started
Display controls
The buttons available on Element™ displays and their function are
detailed below.
1. Waypoint
• Press to place a waypoint at your vessel’s position (unless
cursor mode is active in the Chart or Fishfinder app).
• Press to place a waypoint at the cursor’s position in the Chart
and Fishfinder apps (when in cursor mode).
2. Home
• Press to display the Homescreen.
3. Menu
• Press to open Homescreen menus and app menus.
• Press and hold for approximately 2 seconds to switch which app
has focus in a multi app page.
• Press to close Homescreen menus and app menus.
4. Directional pad (8–axis directional controls)
• Use to navigate Homescreen and menus.
• Press any direction to activate cursor mode in the Chart and
Fishfinder apps.
• Use to position the cursor in the Chart and Fishfinder apps.
5. Back

10
• Return to previous menu or dialog.
6. OK — Confirms menu selections, opens context menus
• Press to confirm a currently highlighted option.
• Press to open context sensitive menus in the Chart and
Fishfinder apps.
7. Minus (Zoom / Range out)
• Press to increase the area displayed onscreen in the Chart app.
• Press to decrease the zoom level in the Fishfinder app, when in
Zoom mode.
• Press to revert to scrolling mode from lowest zoom level in the
Fishfinder app.
8. Plus (Zoom / Range in)
• Press to decrease the area displayed onscreen in the Chart app.
• Press once to initiate Zoom mode in the Fishfinder app,
subsequent presses will increase the zoom level.
9. Quicklaunch 1 /Quicklaunch 2 /Quicklaunch 3
• Press to open the assigned app page.
• Press and hold to assign the quick launch button to the app
page currently highlighted on the Homescreen.
10. Power
• Power on — Press and hold until the display beeps
(approximately 2 seconds).
• Shortcuts menu — Press once to open the shortcuts menu.
• Power off — Press and hold until the display turns off
(approximately 5 seconds).
• Power off — Press to open the Shortcuts menu and then select
Power down display.
Startup wizard
The first time the display is powered up, or after a Factory reset the
Startup wizard is displayed.
The Startup wizard helps you to configure the following display
settings:
• User interface language
• Boating activity
• Boat details including:
– Safety clearances
– Number of engines

11
– Number of tanks
– Number of batteries
– Sonar transducer selection
– Radar selection
Follow the onscreen instructions to configure the relevant settings.
Important:
• Ensure you select the correct type of transducer, an incorrect
selection will require a factory reset to correct.
• Ensure that Radar installed option is enabled if you intend to
connect a Quantum radar scanner to the display.
First power up Limitation on Use acknowledgement
After you have completed the Startup wizard the Limitation on Use
(LoU) disclaimer is displayed.
You must read and agree to the terms in order to use your display.
Selecting OK means you have accepted the terms of use.
Configuring transducer settings
For systems with a transducer connected, as part of setting up your
system for the first time it is important that you correctly configure
your transducer.
Transducer configuration settings are available from the Fishfinder
app.

12
1. Select Transducer from the Fishfinder app’s Settings menu: Menu
> Settings > Transducer
2. If your installation required you to install an all-in-one transducer
backwards (e.g.: this may occur when connecting the transducer to
a trolling motor), then select Backwards from the HV transducer
alignment option. This ensures that the port and starboard
channels appear correctly orientated onscreen, otherwise keep
the default setting: Forwards.
3. Select where you want your depth measurements taken from:
i. Below transducer (default) — No offset required
ii. Below keel — Enter the distance between the transducer face
and the bottom of the keel.
iii. Below waterline —Enter the distance between the bottom of
your keel and the waterline.
4. You can configure temperature settings as follows:
i. Enable or disable temperature readings as required.
ii. If enabled, check the temperature reading against the actual
water temperature.
iii. If the current reading requires adjustment, select Calibrate
temp and enter the difference between your 2 readings.
Identifying engines
Engine data can be shown on your display, if your engines are
transmitting the relevant supported data on the same network as your
display. If your system has mislabelled your engines then you can
correct this using the Engine identification wizard.
The Engine identification wizard can be accessed from the Boat details
menu: Homescreen > Settings > Boat details > Identify engines.

13
1. Ensure the correct number of engines is selected in the Num of
Engines: box.
2. Select Identify engines.
3. Follow the onscreen prompts to complete the engine identification
wizard.
Performing a settings or factory reset
Performing a Factory reset will erase ALL user data and reset the
display’s settings to their Factory default values. Performing a Settings
reset will restore your display’s settings to factory defaults, whilst
retaining user data.
1. Select Settings reset, from the This display menu: Homescreen >
Settings > This display > Settings reset to perform a settings reset.
2. Select Factory reset, from the This display menu: Homescreen >
Settings > This display > Factory reset to perform a factory reset.
2 2 Shortcuts
The Shortcuts menu can be accessed by pressing the Power button.
The following shortcuts are available:
•Display brightness
•Take Screenshot
•Eject SD card
•Color theme:
•(1)Radar Tx:
•Sonar ping:
•Power down display

14
Note:
• If no controls are pressed, the Shortcuts menu will automatically
close after approximately 5 seconds.
•(1)Radar transmission controls are only available when the display
is paired with a compatible radar scanner.
2 3 Switching active app
On app pages that contain more than 1 app you can select which app
has the current focus (i.e.: which app responds to your control).
Press and hold the Menu button to move focus to the next app.
In addition to pressing and holding on the Menu button you can also
switch app focus from the app menu. With a multi app page displayed:
1. Press the Menu button.
2. Highlight the Switch to option.
3. In app pages with more than 2 apps, use the Right and Left buttons
to highlight the app you want to make active.
4. Press the OK button.
5. Press the Back button to close the menu.

15
2 4 Memory card compatibility
MicroSD memory cards can be used to backup / archive data (e.g.
Waypoints, Routes and Tracks). Once data is backed up to a memory
card, old data can be deleted from the system. The archived data can
be retrieved at any time. It is recommended that your data is backed
up to a memory card on a regular basis.
Compatible cards
The following types of MicroSD cards are compatible with your MFD:
Type Size
Native card
format
MFD
supported
Format
MicroSDSC (Micro
Secure Digital
Standard Capacity)
Up to 4GB FAT12,
FAT16 or
FAT16B
NTFS,
FAT32
MicroSDHC (Micro
Secure Digital High
Capacity)
4GB to 32GB FAT32 NTFS,
FAT32
MicroSDXC (Micro
Secure Digital
eXtended Capacity)
32GB to 2TB exFAT NTFS,
FAT32
•Speed class rating — For best performance it is recommended that
you use Class 10 or UHS (Ultra High Speed) class memory cards, or
better.
•Use branded memory cards — When archiving data it is
recommended that you use good quality branded memory cards.
Removing MicroSD card from its adaptor
MicroSD memory and cartography chart cards are usually supplied
inserted into an SD card adaptor. The card will need to be removed
from the adaptor before inserting into your display.

16
Inserting a MicroSD card
1. Open the card reader door.
2. Ensuring correct orientation (contacts facing down), insert the
MicroSD card into the card reader slot.
3. Close the card reader door, ensuring that the edges of the door
are flush.
Removing the MicroSD card
1. Press the Power button.
The Shortcuts menu is displayed.
2. Select Eject SD card.
3. Open the card reader door.
4. Remove the MicroSD card from the Rear of the MFD.
5. Close the card reader door.
6. Select OK on the confirmation dialog.
Caution: Ensure card reader cover or door
is securely closed
To prevent water ingress and consequent damage to
the product, ensure that the card reader door or cover
is firmly closed.

17
2 5 Data sources menu
When a network / system includes multiple sources of the same data
type, such as GPS / GNSS position data, the display will choose the
most appropriate source for the data. If you prefer, you can manually
select your own source for the data.
The Data sources menu can be accessed from the Settings menu:
Homescreen > Settings > This display > Data sources.
Each tab in the data sources menu enables you to view and select
your preferred data source for that type of data. The currently active
data source will display its current ‘value in use’. By default data
sources are selected automatically and the source for the data may
change depending on conditions.
With the Manual selection toggle enabled, you can manually assign
your preferred source for the data. Manually selected data sources
will not change.
Manually assigning a data source
To manually assign a data source follow the steps below.
From the Homescreen:
1. Select Settings.
2. Select the This display tab.
3. Select the Data sources button.
4. Select the tab for the type of data you want to assign a source for.
Once a tab is selected the display will search the network and list
all compatible devices that provide that data type.
5. Use the Up and Down buttons to highlight a device.
6. Press the OK button to select the device as the source for that
data type.
The selected device will become the only source used for that data.

18
Note:
Unless manual selection is required for a specific reason, it is
recommended that Manual selection remains disabled, so that the
display can determine the best source for the data.
2 6 EV-1 heading sensor
You can connect an EV-1 heading sensor to your display, this will
ensure that accurate heading data is available, regardless of vessel
movement.
The EV-1 heading sensor will automatically calibrate (linearize) itself
while the following conditions are met:
• vessel speed is between 3 to 15 knots, and
• at least a 270° turn has been made.
Note:
The time it takes for automatic calibration can be reduced by
completing a full 360° turn at between 3 to 15 knots.
After the initial calibration has been completed a notification will be
displayed and a Max deviation value will be reported in the EVO
COMPASS section of the This display menu. If dashes are displayed
then the calibration has not been successful.
If the Maximum deviation is 45° or greater, it is recommended
that either the EV-1 is relocated, in a location with less magnetic
interference, or that any devices causing magnetic interference are
moved farther away from the EV-1.
2 7 Software updates
Raymarine® regularly issues software updates for its products which
provide new and enhanced features and improved performance and
usability.
It is important to ensure that you have the latest software for your
products by regularly checking the Raymarine® website for new
software releases.
www.raymarine.com/software

19
Note:
• It is recommended that you always backup your User data before
performing a software update.
• The “Check online” feature is only available on display variants
that include built-in Wi-Fi that have been configured with an active
Internet connection.
• In order to perform a software update any connected radar
scanner must be switched to standby.
In addition to updating your display’s software, your display can also
be used to update the software of devices connected to the same
SeaTalkng ® backbone.
Updating display software using a memory card
Follow the steps below to update the software on your display.
1. Check the product hardware variant and the software version of
the products you want to update.
2. Go to the Raymarine website: (www raymarine com > Support >
Software Updates).
3. Browse for your product.
4. Check if an updated software version is available for your product.
5. Download the relevant software package(s) (ISO files).
6. Copy the files to MicroSD card.
7. With your display powered on, insert the MicroSD card into the
card reader slot.
The software update files will be recognized automatically.
8. Select Yes to update the software.
A list of available products is displayed. The list will include
your display and products that are connected to the SeaTalkng ®
backbone.

20
Software update list example
9. Select each device that you want to update.
If a notification is displayed asking if you want to reinstall the
current software version, unless you are experiencing problems
with the product select No, otherwise select Yes and the current
version of software will be reinstalled.
10. When all relevant products have been chosen, select Update
selected to commence the software update process.
11. Wait for the update process to complete.
12. Select Exit.
Note:
• Your products may reboot automatically as part of the update
process.
• You can also select Check SD card from the Update software
pop-over options (Homescreen > Settings > Getting started >
Update software.
Updating software using an internet connection
When using an Element™ display that includes built-in Wi-Fi, follow
the steps below to update your display’s software and software on
approved devices connected to the same SeaTalkng ®backbone, using
an internet connection.
1. Select Update software from the Getting started menu:
(Homescreen > Settings > Getting started).