Razor GGC2241M-A User manual

Outdoor LP Gas Griddle
Model No. GGC2241M-AModel No. GGC2241M-A
(Manufacture Code(Manufacture Code：：BGC2241M)BGC2241M)
OWNER’SOWNER’S MANUALMANUAL
Table of Contents
Important Safeguards ...........................................................Page 2
Expanded View & Hardware .......................................................... 4
Assembly Instructions............................................................... 5
Transporting & Storage Instructions .................................................... 8
Optional Part Instructions ........................................................... 11
Installing LP Gas Tank.............................................................. 13
Operating Instructions.............................................................. 13
Cleaning and Care ................................................................ 14
Product Registration ............................................................... 15
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Limited Warranty ................................................................. 15
Troubleshooting .................................................................. 16
The use and installation must conform with local codes or, in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1,
or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/
NFPA 1192, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
If you are assembling this unit for someone else, give this manual to them to read and save for future
reference.
Made from 75% Bagasse
(environmentally friendly sugar
cane pulp by-product)
WARNING
FOR YOUR SAFETY:
For Outdoor Use Only!
(outside any enclosure)
WARNING
FOR YOUR SAFETY:
1. Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
2. Read the installation, operation, and
maintenance instructions thoroughly
before installing or servicing this
equipment.
3. Failure to follow these instructions could
result in fire or explosion, which could
cause property damage, personal injury, or
death.
4. This instruction manual contains important
information necessary for the proper
assembly and safe use of the appliance.
5. Read and follow all warnings and
instructions before assembling and using
the appliance.
6. Follow all warnings and instructions when
using the appliance.
7. Keep this manual for future reference.
DANGER
If you smell gas -
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. Open side shelves.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
WARNING
FOR YOUR SAFETY:
1. Do NOT store or use gasoline or other
flammable liquids or vapors in the vicinity
of this or any other appliance.
2. An LP cylinder not connected for use shall
NOT be stored in the vicinity of this or any
other appliance.
DANGER
Never operate this appliance unattended.
Manufactured in China for: RevoAce Inc. Limited
Hong Kong, China • 1.800.694.0013 • ser[email protected]
8:00 am to 4:00 pm central time, Monday to Friday.
© RevoAce Inc. Limited
Razor®is a registered trademark of Mr. Bar-B-Q Products LLC. Used with permission.
GriddleOn is a trademark of Mr. Bar-B-Q Products LLC. Used with permission.
Make it SizzleTM is a trademark of Mr. Bar-B-Q Products LLC. Used with permission. GGC2241M-A-RA-E-OM-F102
IMPORTANT
After each use, always season your griddle per “Seasoning
Griddle” section.
WARNING
FOR YOUR SAFETY:
DO NOT LEAVE THIS APPLIANCE UNATTENDED
WHILE IN USE.
razorgriddle.com
@razorgriddle
@razorgriddle
¸WARNING: This product can expose you to chemicals including carbon
monoxide, soot, lead and lead components, which are known to the State
of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
PATENT NO. D909,131S
AND OTHER PATENTS PENDING

Outdoor LP Gas Griddle
Model No. GGC2241M-A
2
WThis griddle is for outdoor use only, and should not be used in a
building, garage or any other enclosed area.
WDo NOT operate, light or use this appliance within ten feet (3.05 m) of
walls, structures or buildings.
WFor residential use only. This griddle is NOT for commercial use.
WThis griddle is not intended for and should never be used as a heater.
TOXIC fumes can accumulate and cause asphyxiation.
WThis griddle is safety certified for use in the United States and/or
Canada only. Do NOT modify for use in any other location. Modification
will result in a safety hazard and will void your warranty.
WThis griddle is for use with liquid propane (LP) gas only. The conversion
to or attempted use of natural gas in this LP gas griddle is dangerous,
may cause bodily harm and will void your warranty.
WLP gas characteristics:
a. LP gas is flammable and hazardous if handled improperly. Become
aware of the characteristics before using any LP gas product.
b. LP gas is explosive under pressure, heavier than air, and settles/
pools in low areas.
c. LP gas in its natural state has no odor. For your safety, an odorant is
added that smells like rotten cabbage.
d. Contact with LP gas can cause freeze burns to skin.
WApartment dwellers: Check with management to learn the requirements
and fire codes for using a LP gas griddle in your apartment complex.
If allowed, use outside on the ground floor with a ten foot (3.05 m)
clearance from any structure. Do NOT use on or under balconies.
WLP gas cylinder needed to operate. Only cylinders marked “propane”
may be used.
WThe LP gas cylinder must be constructed and marked in accordance
with the Specifications for LP-gas Cylinders of the U.S. Department
of Transportation (D.O.T.) or the National Standard of Canada, CAN/
CSA-B339, Cylinders, Spheres and Tubes for the Transportation of
Dangerous Goods; and Commission.
WLP gas cylinder must be arranged for vapor withdrawal.
WThe LP gas cylinder must have a listed overfilling prevention device
(OPD).
WOnly use LP gas cylinders equipped with a cylinder connection device
compatible with the connection for outdoor cooking appliances.
WThe LP gas cylinder must have a cylinder collar to protect the cylinder
valve.
WNever use an LP gas cylinder with a damaged body, valve, collar or
footing.
WDented or rusted LP gas cylinders may be hazardous and should be
checked by your LP gas supplier prior to use.
WThe LP gas cylinder should not be dropped or handled roughly.
WLP gas cylinders must be stored outdoors out of the reach of children
and must not be stored in a building, garage or any other enclosed area.
Your cylinder must never be stored where temperatures can reach over
125°F.
WDo NOT insert any tool or foreign object into the valve outlet or safety
relief valve. You may damage the valve and cause a leak. Leaking
propane may result in an explosion, fire, severe personal injury or death.
WDo NOT block holes in sides or back of griddle.
WNever keep an LP gas cylinder in a hot car or trunk. Heat will cause the
gas pressure to increase, which may open the relief valve and allow gas
to escape.
WPlace dust cap on cylinder valve outlet whenever the cylinder is not in
use. Only install the type of dust cap on the cylinder valve outlet that is
provided with the cylinder valve. Other types of caps or plugs may result
in leakage of propane.
WIf griddle is not in use, the gas must be turned off at the supply cylinder
and disconnected.
WDo NOT store a spare LP gas cylinder under or near this appliance.
WNever fill the cylinder beyond 80 percent full.
WA fire causing serious injury or damage to property may occur if the
above is not followed exactly.
WNever attempt to attach this griddle to the self-contained LP gas system
of a camper trailer, motor home or house.
WNever use charcoal, lighter fluid, lava rocks, gasoline, kerosene or
alcohol with this product.
WYour griddle has been checked at all factory connections for leaks.
Re-check all connections as described in the “Operating Instructions”
section, as shipping can loosen connections.
WCheck for leaks even if your unit was assembled for you by someone
else.
WDo NOT operate if a gas leak is present. Gas leaks may cause a fire or
explosion.
WYou must follow all instructions in the “Checking for Leaks” section
before operating. To prevent fire or explosion hazard when testing for a
leak:
a. Always perform a leak test before lighting the griddle and each time
the cylinder is connected for use.
b. No smoking. Do NOT use or permit sources of ignition in the area
while conducting a leak test.
c. Conduct the leak test outdoors in a well-ventilated area.
d. Do NOT use matches, lighters, or a flame to check for leaks.
e. The use of alcohol, prescription or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely operate
the appliance.
f. Strong odors, colds, sinus congestion, etc. may prevent the
detection of propane. Use caution and common sense when testing
for leaks.
g. Do NOT use griddle until any and all leaks are corrected.
If you are unable to stop a leak, disconnect the LP gas supply. Call a
gas appliance serviceman or your local LP gas supplier.
WThis griddle is designed to operate at an inlet pressure of: 11 inches
water column.
WDo NOT store or use gasoline or other flammable liquids or vapors
within 25 feet (7.62 m) of this appliance.
WDo NOT use in an explosive atmosphere. Keep griddle area clear and
free from combustible materials, gasoline and other flammable vapors
and liquids.
WMinimum clearance from sides and back of unit to combustible
construction is 36 inches (91.5 cm). Do NOT use this appliance under
any type of overhang or roof.
WIt is essential to keep the griddle’s valve compartment, burners and
circulating air passages clean.
WInspect griddle before each use.
WDo NOT alter griddle in any manner. Any alteration will void your
warranty.
WDo NOT use the griddle unless it is COMPLETELY assembled and all parts
are securely fastened and tightened.
WDo NOT build this model of griddle in any built-in or slide-in
construction. Ignoring this warning could cause a fire or an explosion
that can damage property and cause serious bodily injury or death.
WThis griddle should be thoroughly cleaned and inspected on a regular
basis.
WClean and inspect the hose before each use of the appliance. If there
is evidence of abrasion, wear, cuts or leaks, the hose must be replaced
prior to operation.
WUse only the regulator and hose assembly provided. Use only the
replacement regulator and hose assembly specified by RevoAce Inc.
Limited
WUse only RevoAce Inc. Limited factory-authorized parts. The use of any
part that is not factory-authorized can be dangerous and will void your
warranty.
WDo NOT operate this appliance without reading “Operating Instructions”
in this manual.
WDANGER: Failure to follow the dangers, warnings and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion
causing damage to property.
WWARNINGS:
Important Safeguards

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 3
WDo NOT touch metal parts of griddle until they have completely cooled
to avoid burns, unless you are wearing protective gear (pot holders,
gloves, BBQ mittens, etc.).
WDo NOT install or use in or on boats or recreational vehicles.
WWhen cooking, fire extinguishing materials should be readily accessible.
In the event of an oil/grease fire, do NOT attempt to extinguish with
water. Use type BC dry chemical fire extinguisher or smother with dirt,
sand or baking soda.
WDo NOT use griddle in high winds.
WNever lean over the griddle when lighting.
WDo NOT leave a lit griddle unattended. Keep children and pets away from
griddle at all times.
WDo NOT leave griddle unattended while preheating or burning off food
residue on high. If griddle has not been cleaned, a grease fire can occur
that may damage the product.
WDo NOT place empty cooking vessels on the appliance while in
operation.
WUse caution when placing anything on the griddle while the appliance is
in operation.
WDo NOT attempt to move griddle when in use. Allow the griddle to cool
before moving or storing.
WLP gas cylinder must be properly disconnected and removed prior to
moving this griddle.
WStorage of griddle indoors is permissible only if the cylinder is
disconnected, removed from the griddle and properly stored outdoors.
WDo NOT attempt to disconnect the gas regulator from the cylinder or any
gas fitting while the griddle is in use.
WAlways place your griddle on a hard, non-combustible, level surface. An
asphalt or blacktop surface may not be acceptable for this purpose.
WMove gas hoses as far away as possible from hot surfaces and dripping
hot grease.
WKeep all electrical cords away from a hot griddle.
WAfter a period of storage and/or nonuse, check for leaks, burner
obstructions and inspect for any abrasion, wear or cuts to the hose.
WFailure to open side shelves while igniting the griddle’s burners, or not
waiting 5 minutes to allow the gas to clear if the griddle does not light,
may result in an explosive flame-up.
WAlways use a meat thermometer to ensure food is cooked to a safe
temperature.
WUse protective gloves when assembling this product.
WDo NOT force parts together as this can result in personal injury or
damage to the product.
WNever cover entire cooking area with aluminum foil.
WDeaths, serious injury or damage to property may occur if the above is
not followed exactly.
Important Safeguards

Outdoor LP Gas Griddle
Model No. GGC2241M-A
4
Tools Required for Assembly (Included)
#2 Phillips Head Screwdriver 1 pc
M10-M5 Wrench 2 pcs
Hardware
AScrew M6x16 Nickel Plated Phillips Truss Head 8 pcs
BNut M10 Nickel Plated Phillips Truss Head 2 pcs
CPin Φ8X45 Nickel Plated 2 pcs
DCotter Pin Φ1.4X38 Nickel Plated 2 pcs
Parts List
1Griddle Surface* G2241-010
2Left Side Shelf* G2241-020
3Towel Bar (2) G1643-030
4U Burner* G1643-040
5Burner (3)* G1643-050
6Griddle Body Assembly* G2241-030
7Right Side Shelf* G2241-040
8Main Control Knob
Bezel (4)* G2225-080
9Control Knob (4) G2225-100
10 Brand Plate* G2225-090
11 Locking Wheel (2)* G1643-080
12 Left Cart Frame* G2241-050
13 Right Cart Frame* G2241-060
14 Side Handle (2) G2241-070
15 Rubber Spacer(4)* G1643-230
16 Grease Cup G1643-120
17 Regulator/Hose
Assembly* B0308-A18
18 Lighting Hook* B0223-D04
19 Upper LP Gas Tank
Support* †G1643-130
20 Leg Locking Assembly* G1643-140
21 Lower LP Gas Tank
Support* †G1643-150
22 Wheel (2) G1643-160
23 Axle G2241-080
24 Bottom Shelf G2241-090
25 Bottom Shelf Screw (2) G1643-180
26 Side Shelf Lock A (2)* †B0107-E05
27 Side Shelf Lock B (2)* †B0107-I09
28 LP Gas Tank Heat
Shield* G2241-100
29 Bottle Opener#G1932-11L
30 Side Windshield (2) #G2241-101
31 Rear Windshield#G2241-102
32 Paper Towel Holder#G2225-230
33 Front Panel#G2241-104
34 Condiment Holder#G2241-105
* Pre-assembled
†Not replaceable
# Optional part
Expanded View
1
5
2
3
3
7
4
6
8
10
8
9
25
11
12
13
14
14
16
15
15
17
18
29
19
20
23
30
31
22
33
34
22
21
24
25
26
26
26
27
27
28
30
32

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 5
3
Remove Nuts from Towel Bar and Attach onto Side
Shelves
Remove Bottom Shelf and Axle
1
DO NOT RETURN TO PLACE OF PURCHASE.
For assistance, call 1.800.694.0013 toll-free. Please have
your owner’s manual and model number available for
reference.
Note: The model number is printed on a label which can be found on
the bottom shelf.
Assembly Tips:
1. Select an area where you will assemble this product. To
protect components, choose a smooth surface that’s free of
cracks or openings.
2. Spread out all parts.
3. Tighten all hardware connections by hand first. Then, before
completing each step, go back and fully tighten all hardware.
Be careful not to over-tighten. That could damage surfaces or
strip threads.
4. For best results, complete each step in the order presented.
To complete assembly you will need:
• (1) Leak detection solution (instructions on how to make the
solution are included in the “Operating Instructions” section of
this manual).
• (1) Precision-filled LP gas grill tank with Acme Type 1 external
threaded valve connection (standard grill size) (not included).
Typical assembly is approximately 30 minutes.
WCAUTION: Two (2) people are required for
assembly.
Assembly Instructions
2
Unlock Side Shelves
Open Side Shelves
Open right side shelf first, then left side shelf. Make sure side shelves are pushed all
the way down.
Note: support springs may cause the side shelves NOT to rest completely flush with
the side handles.
WCAUTION: Hold side shelf securely while opening. Do NOT
release until fully extended.
WCAUTION: Maximum side shelf weight is 33 lbs (15 kg).
4
Close Side Shelves
Close left side shelf first, then right side shelf.
WCAUTION: Hold side shelf securely while closing. Do NOT
release until fully closed.
Lock Side Shelves
1
1
2
2
3
211
1 2 3
2

Outdoor LP Gas Griddle
Model No. GGC2241M-A
6
Assembly Instructions (continued)
7
Attach Bottom Shelf
6
Open Legs
WCAUTION: Two (2) people will be required to lay griddle on
back.
Note: Open right leg first.
5
Attach Wheels
Bx 2
8
Fix Legs
Cx 2 Dx 2
B
Face in
12
3
4
C
D

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 7
Assembly Instructions (continued)
10
Insert Grease Cup
9
Attach Side Handles and Insert Control Knobs
WCAUTION: Two (2) people will be required to stand griddle
upright.
Ax 8
12
Close Side Shelves
Close left side shelf first, then right side shelf.
WCAUTION: Hold side shelf securely while closing. Do NOT
release until fully closed.
Lock Side Shelves
11
Unlock Side Shelves
Open Side Shelves
Open right side shelf first, then left side shelf. Make sure side shelves are pushed all
the way down.
Note: support springs may cause the side shelves NOT to rest completely flush with
the side handles.
WCAUTION: Hold side shelf securely while opening. Do NOT
release until fully extended.
WCAUTION: Maximum side shelf weight is 33 lbs (15 kg).
A
1
1
1
1 2 3
2
2
2 3

Outdoor LP Gas Griddle
Model No. GGC2241M-A
8
Transporting & Storage Instructions
1
WWARNING: Before transporting or storing this
griddle:
a. Always season griddle per “Seasoning
Griddle” section.
b. Always clean griddle per “Cleaning
Instructions” section.
c. Always wait until griddle is cool.
d. Always turn griddle off per “Turning Off”
section.
e. Always disconnect tank per “Disconnecting
LP Gas Tank” section.
f. Always empty and properly dispose of all
items in grease cup.
WWARNING: When transporting or storing this
unit, always follow the instructions found in
this section.
WCAUTION: Two (2) people will be required to
prepare for transportation and/or storage.
2
Secure LP Gas Tank Supports
4
Remove Bottom Shelf
WCAUTION: Two (2) people will be required to lay griddle on
back.
3
Close Side Shelves
Close left side shelf first, then right side shelf.
WCAUTION: Hold side shelf securely while closing. Do NOT
release until fully closed.
Lock Side Shelves
1
4
2
5
3
6
1 2
123
IMPORTANT
Before first use and after each use, always
season your griddle per “Seasoning Griddle”
section.

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 9
Transporting & Storage Instructions
5
Attach Bottom Shelf Screws
6
Remove Fixed Axis
8
Fixed Axis
7
Close Legs
Note: Close left leg first.
1 2
3 4

Outdoor LP Gas Griddle
Model No. GGC2241M-A
10
Transporting & Storage Instructions (continued)
11
Close Side Shelves
Close left side shelf first, then right side shelf.
WCAUTION: Hold side shelf securely while closing. Do NOT
release until fully closed.
Lock Side Shelves
1
1 32
2
10
Place Bottom Shelf
9
Unlock Side Shelves
Open Side Shelves
Open right side shelf first, then left side shelf. Make sure side shelves are pushed all
the way down.
Note: support springs may cause the side shelves NOT to rest completely flush with
the side handles.
WCAUTION: Hold side shelf securely while opening. Do NOT
release until fully extended.
WCAUTION: Maximum side shelf weight is 33 lbs (15 kg).
1
21
2 3

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 11
2
Attach Side & Rear Windshield
Optional Part Instructions
Spatulas (No Included)
1
Attach Bottle Opener
A#x 2 (pack in bulk box)
A#
1
2
3
3
Attach Paper Towel Holder
Note: Remove the cotter pins from the holder and then attach the tissue holder onto the support.
12
3
12
3
4
5
Tissue (not included)

Outdoor LP Gas Griddle
Model No. GGC2241M-A
12
4
Attach Front Panel and Condiment Holder
1 2 3

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 13
Installing LP Gas Tank
To operate, you will need one precision-filled standard barbecue
grill LP gas tank with external valve threads.
WCAUTION: LP gas tank must be properly
disconnected and removed prior to moving this
griddle.
Inserting and Securing LP Gas Tank
1. Unfold the upper LP gas tank support.
2. Unfold the lower LP Gas tank support.
3. Place precision-filled LP gas tank upright onto the upper and lower LP gas tank support so
the tank valve is facing the gas line connection.
Connecting LP Gas Tank
1. Make sure control knobs are in the “ OFF” position
(Figure 2).
2. Before connecting, be sure there is no debris caught
in the head of the LP gas tank, head of the regulator
valve or in the head of the burner or burner ports.
3. Connect regulator/hose assembly to tank by turning
knob clockwise until it stops.
4. Perform leak test per “Checking for Leaks” section.
Disconnecting LP Gas Tank
1. Make sure control knobs are in the “ OFF” position
(Figure 2).
2. Before disconnecting, make sure the LP gas tank valve
is “CLOSED.”
3. Disconnect regulator/hose assembly from LP gas tank
by turning knob counterclockwise until it is loose.
WCAUTION: LP gas tank must be properly
disconnected and removed prior to
moving this griddle.
4. Place the protective cap cover on the LP tank and
store the tank outdoors in a well ventilated area out of direct sunlight.
20 lb
9 Kg
17.9 in. / 45.5 cm
12.2 in. / 31 cm
Operating Instructions
Checking for Leaks
Burner Connections
1. Make sure the regulator hose and valve
connections are securely fastened to the burner
and the tank.
2. Visually check the connection between the burner/
venturi tube and orifice.
3. Make sure the burner/venturi tube fits over the
orifice.
WWARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury or damage to property.
4. Please refer to diagram for proper installation
(Figure 1).
5. If the burner/venturi tube does not rest flush to the
orifice, as shown, please contact 1.800.694.0013
for assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak detection solution by mixing
one part liquid dish washing soap with three parts
water.
2. Make sure control knobs are in the “ OFF”
position (Figure 2).
3. Connect LP gas tank per “Installing LP Gas Tank”
section.
4. Turn LP gas tank valve to “OPEN.”
5. Spoon several drops of solution, or use a squirt
bottle, at all “X” locations (Figures 1 and 3).
a. If any bubbles appear, turn LP gas tank valve to
“CLOSED,” reconnect and re-test.
b. If you continue to see bubbles after several
attempts, turn LP gas tank valve to “CLOSED”
and disconnect LP gas tank, per “Disconnecting
LP Gas Tank” section. Contact 1.800.694.0013
for assistance.
c. If no bubbles appear after one minute, turn LP
gas tank valve to “CLOSED,” wipe away solution
and proceed.
Operating Main Burners
First Use
1. Make sure all labels, packaging and protective
films have been removed from the griddle.
2. Light griddle per “Lighting” section.
3. Remove manufacturing oils before cooking on this
griddle for the first time.
4. Season your griddle per “Seasoning Griddle”
section.
Lighting
WCAUTION: Keep outdoor gas cooking
appliance area clear and free from
combustible materials, gasoline and
other flammable vapors and liquids.
WCAUTION: Do NOT obstruct the flow of
combustion and ventilation air.
WCAUTION: Check and clean burner/
venturi tubes for insects and insect
nests. A clogged tube can lead to a
fire.
WCAUTION: Do NOT use non-stick
cooking sprays because they contain
a lot of water and can burn onto the
griddle, damaging the surface.
WCAUTION: Do NOT use corn oil as it
contains a high level of sugar, which can carmelize and burn onto the
surface.
1. Open side shelves.
2. Check for obstructions of airflow to the burners. Spiders, insects and webs can clog the
burner/venturi tube. A clogged burner tube can lead to a fire.
3. All control knobs must be in the “ OFF” position (Figure 2).
4. Connect LP gas tank per “Installing LP Gas Tank” section.
Figure 1
Burner/
Venturi Tube
LP Gas
Valve with
Orifice
LP Gas
Connection
Figure 2
OFF
HIGH
LOW
Figure 3
X
XX
XX
Figure 4
Lighting
Hook
Match
Figure 5
Lighting
Hook
Match

Outdoor LP Gas Griddle
Model No. GGC2241M-A
14
Before Each Use:
1. Keep the griddle area clean and free from any
combustible materials, gasoline, and other
flammable vapors and liquids.
2. Do NOT obstruct the flow of the combustion of LP
gas and the ventilation of air.
3. Keep the ventilation opening(s) of the LP gas tank
area free and clear from debris.
4. Visually check the burner flames to make sure
your griddle is working properly (Figure 11).
5. See sections below for proper cleaning and
seasoning instructions.
6. Check for obstructions of airflow to the burners.
Spiders, insects and webs can clog the burner/
venturi tube. A clogged burner tube can lead to
a fire.
Cleaning Cart Surfaces
1. Wipe surfaces clean with mild dish washing
detergent or baking soda mixed with water.
2. For stubborn surfaces, use a citrus-based
degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.
Cleaning Main Burners
WCAUTION: Two (2) people will be
required to remove griddle.
1. Turn LP gas tank valve to “CLOSED.”
2. Turn all control knobs clockwise to the “ OFF”
position.
Note: A “poof” sound is normal as the last of the
gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP
Gas Tank” section.
4. Remove griddle by lifting it off the cart.
5. Remove burners by removing the fasteners, which
secure the burners to the frame bottom.
6. Lift burners up and away from gas valve orifice.
7. Disconnect wire from spark electrode.
8. Clean venturi of each burner with small bottle
brush or compressed air.
9. Remove all residue and dirt from burner surface.
10. Clean any clogged ports with a stiff wire (such as
an opened paper clip).
11. Inspect burners for any damage (cracks or holes).
If damage is found, replace with new burner(s)
from manufacturer.
12. Re-install burner(s). Checking to insure that gas
valve orifice is correctly positioned inside each
burner/venturi tube. Also, check position of spark
electrode.
13. Connect wire to spark electrode.
14. Replace griddle.
15. Connect LP gas tank per “Installing LP Gas Tank” section.
16. Perform leak test per “Checking for Leaks” section.
Before Storing
1. Turn LP gas tank valve to “CLOSED.”
2. Turn all control knobs clockwise to the “ OFF” position.
Note: A “poof” sound is normal as the last of the gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
4. Clean all surfaces.
5. Lightly coat the burner(s) with cooking oil to prevent excess rusting.
6. Season your griddle per “Seasoning Griddle” section.
7. If storing the griddle indoors, disconnect the LP tank per “Disconnecting LP Gas Tank”
section.
8. Place the protective cap cover on the LP tank and store the tank outdoors in a well-
ventilated area out of direct sunlight.
9. If storing the griddle indoors, cover the griddle and store in a cool dry place.
10. If storing the griddle outdoors, cover the griddle with a griddle cover for protection from the
weather.
Seasoning Griddle
Important: season your griddle every time you use it.
Griddle chefs at Japanese steakhouses and short-order restaurants season their griddles all the
time, and it is critical for you to do it too. Seasoning helps prolong the life of your griddle, makes
the cooking surface non-stick and helps prevent rust.
5. Turn LP gas tank valve to “OPEN.”
6. Push and turn any control knob to (HIGH). The
burner should light. If it does not, repeat up to
three times.
7. If ignition does not occur in 5 seconds, turn
burner control knob “ OFF,” wait 5 minutes, and
repeat lighting procedure.
8. If igniter does not light burner, use a lit match
secured with the Lighting Hook (included with the
griddle) to light burners. Access the burners from
under the griddle. Position lit match near side of
burner (Figures 4 and 5).
Important: Always use the Lighting Hook (included) when lighting burners with a match.
9. After lighting, observe the burner flame. Make sure all burner ports are lit and flame height
matches illustration (Figure 6).
Note: Each burner lights independently - repeat steps 5-9 for the other burners.
WCAUTION: If burner flame goes out during operation, immediately turn
the control knobs to the “ OFF” position, turn the LP gas tank valve
to “CLOSED” and open side shelves to let the gas clear for 5 minutes
before re-lighting.
Turning Off
1. Turn LP gas tank valve to “CLOSED.”
2. Turn all control knobs clockwise to the “ OFF” position (Figure 2).
Note: A “poof” sound is normal as the last of the LP gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
4. Season your griddle per “Seasoning Griddle” section.
Controlling Flare-ups
WCAUTION: Putting out grease fires by only closing the side shelves is
not possible.
1. If a grease fire develops, turn control knobs to the “ OFF” position
and LP gas tank valve to “CLOSED.” Do NOT use water on a grease
fire. This can cause the grease to splatter and could result in
serious burns, bodily harm or other damage.
2. Do NOT leave griddle unattended while preheating or burning off
food residue on (HIGH). If griddle has not been cleaned, a grease
fire can occur.
WWARNING: When cooking, fire extinguishing materials should be
readily accessible. In the event of an oil/grease fire, use type BC dry
chemical fire extinguisher or smother with dirt, sand or baking soda.
Do NOT attempt to extinguish with water.
Flare-ups are a part of cooking meats on a griddle and add to the unique flavor of grilling.
Excessive flare-ups can over-cook your food and be dangerous.
Important: Excessive flare-ups result from the build-up of grease in the grease cup.
If a grease fire occurs, turn the control knob(s) to “ OFF” until the grease burns out.
If excessive flare-ups occur, do NOT pour water onto the flames.
Minimize Flare-ups:
1. Trim excess fat from meats prior to cooking.
2. Cook high fat content meats on (LOW) setting or indirectly.
3. Ensure that your griddle is on a hard, level, non-combustible surface and the grease is
allowed to drain into grease receptacle.
Cleaning and Care
WCAUTION:
1. All cleaning and maintenance should be done when griddle is cool
and with the fuel supply disconnected.
2. Do NOT clean any griddle part in a self-cleaning oven. The extreme
heat will damage the finish.
3. Do NOT enlarge valve orifices or burner ports when cleaning the
valves or burners.
Notices
1. This griddle should be thoroughly cleaned and inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. Never use oven cleaner to clean any part of griddle.
Operating Instructions (continued)
Figure 7
Match
Lighting
Hook
Figure 8
OFF
HIGH
LOW
Figure 9
OFF
HIGH
LOW
Figure 10
OFF
HIGH
LOW
Figure 6
Burner
Flame Slight
Yellow
Slight
Blue
Dark
Blue

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 15
For more information, please visit BlueRhino.com/
RazorFAQ.
Tools needed for seasoning:
• Metal scraper or metal spatula
• Cooking oil, such as vegetable oil or extra virgin
olive oil
• Paper towels
• BBQ stone or steel wool
WCAUTION: Do NOT use corn oil as it
contains a high level of sugar, which
can carmelize and burn onto the
surface.
First Use
1. Light griddle per “Lighting” section.
2. Keep burners on (HIGH) for 15 minutes.
3. Turn griddle off per “Turning Off” section.
4. Allow griddle to cool, but still be slightly warm.
5. Wipe off griddle surface, inner and outer walls
with paper towels until clean.
Note: While drying you may notice the towel may
have some discoloration. This is normal.
6. Apply cooking oil onto griddle surface, inner and
outer walls and evenly coat with rolled up paper
towels.
7. Repeat this process at least twice.
After Each Use
1. Turn griddle off per “Turning Off” section.
2. While the griddle is still warm, gently scrape off
all food residue with a scraper.
3. Wipe down griddle surface, inner and outer walls with a towel or paper towels.
4. For stubborn food residue:
a. Light griddle per “Lighting” section.
b. Apply cooking oil onto griddle surface.
c. Allow oil to “boil” food residue off.
d. Repeat steps 1 through 3.
e. If necessary, use a BBQ stone and scrub the food residue off.
f. Continue with “Seasoning Griddle” instructions.
5. Wipe off griddle surface, inner and outer walls with paper towels until clean.
Note: While drying you may notice the towel has some discoloration. This is normal.
6. Apply finishing oil onto griddle surface, inner and outer walls and evenly coat with rolled
up paper towels.
7. Light griddle per “Lighting” section.
8. Keep burners on (HIGH) for 15 minutes or until cooking oil starts to smoke.
9. Turn griddle off per “Turning Off” section.
10. Repeat steps 6-9 a minumum of 2 additional times.
11. Following “Before Storing” section.
Refurbish the Griddle Surface
1. If griddle is off, light per “Lighting” section for 10 minutes. Then turn griddle off per
“Turning Off” section.
2. If griddle is on, turn griddle off per “Turning Off” section.
3. While the griddle is still warm, use a scraper or metal spatula to remove as much rust and
food residue as you can from the griddle surface, inner and outer walls.
4. Apply a liberal amount of cooking oil onto the griddle surface.
5. Using a BBQ stone, scrub the griddle surface. Apply additional cooking oil as need.
6. Wipe off griddle surface, inner and outer walls with paper towels.
7. Repeat steps 3-5 until paper towels no longer show any rust.
8. Apply cooking oil onto griddle surface, inner and outer walls and evenly coat with rolled up
paper towels.
9. Light griddle per “Lighting” section.
10. Keep burners on(HIGH) for 15 minutes or until cooking oil starts to smoke.
11. Turn griddle off per “Turning Off” section.
12. Repeat steps 7-10 until the surface has a nice dark color.
13. Following “Before Storing” section.
Product Registration
For faster warranty service, please register your product immediately. To register, call
1.800.694.0013.
Replacement Parts
For replacement parts, call 1.800.694.0013.
Limited Warranty
RevoAce Inc. Limited (“manufacturer”) warrants to the original retail purchaser of this
product, and to no other person, that if this product is assembled, maintained, and operated
in accordance with the printed instructions accompanying it, then for a period of one (1) year
from the date of purchase, all parts in such product shall be free from defects in material and
workmanship. Manufacturer may require reasonable proof of your date of purchase. Therefore,
you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair
or replacement of parts, which prove defective under normal use and service and which
manufacturer shall determine in its reasonable discretion upon examination to be defective.
Before returning any parts, you should contact manufacturer’s Customer Service Department
using the contact information listed below. If manufacturer confirms, after examination, a defect
covered by this Limited Warranty in any returned part, and if manufacturer approves the claim,
manufacturer will replace such defective part without charge. If you return defective parts,
transportation charges must be prepaid by you. manufacturer will return replacement parts to
the original retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident,
abuse, misuse, alteration, misapplication, improper installation or improper maintenance or
service by you or any third party, or failure to perform normal and routine maintenance on the
product as set out in this owner’s manual. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or other weather damage,
after purchase.
This Limited Warranty is in lieu of all other express warranties. manufacturer disclaims all
warranties for products that are purchased from sellers other than authorized retailers or
distributors, including the warranty of merchantability or the warranty of fitness for a particular
purpose. MANUFACTURER ALSO DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. MANUFACTURER SHALL HAVE NO LIABILITY TO PURCHASER OR
ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. manufacturer further disclaims any implied or express warranty of, and assumes no
responsibility for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or
limitation of special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to everyone. manufacturer does not
authorize any person or company to assume for it any other obligation or liability in connection
with the sale, installation, use, removal, return, or replacement of its equipment, and no such
representations are binding on manufacturer.
RevoAce Inc. Limited
Hong Kong, China
[email protected]
1.800.694.0013
8:00 am to 4:00 pm central time, Monday to Friday.
Cleaning and Care (continued)
Figure 11
Burner Flame Conditions
Use this chart to see if your burners
need to be cleaned.
1-2 in. /
25.4 - 50.8 mm
Normal: Soft blue flames with yellow
tips between 1 in. - 2 in. height.
Needs cleaning: Noisy with hard
blue flames.
Has to be replaced: Wavy with
yellow flames.

Outdoor LP Gas Griddle
Model No. GGC2241M-A
16
Troubleshooting
Problem Possible Cause Prevention/Cure
Burner will not light using igniter
LP gas tank valve is closed Make sure regulator is securely attached to the LP gas tank per “Installing LP
Gas Tank,” then turn LP gas tank valve to “OPEN”
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Wires or electrode covered with cooking residue Clean wire and/or electrode with rubbing alcohol
Electrode and burners are wet Wipe dry with cloth
Electrode cracked/broken - sparks at crack Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Wire loose or disconnected Reconnect wire or replacement part(s) may be needed - contact Customer Care
at 1.800.694.0013
Wire is shorting (sparking) between igniter and electrode Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Bad igniter Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Burner will not light with match
No gas flow
Check if LP gas tank is empty
A. If empty, exchange, refill or replace LP gas tank
B. If LP gas tank is not empty, refer to “Sudden drop in gas flow or reduced
flame height” (see below)
LP gas tank is low or empty Exchange, refill or replace LP gas tank
LP gas
1. Turn LP gas tank valve to “CLOSED”
2. Wait 5 minutes for gas to clear
3. Follow “Checking for Leaks” section
Coupling nut and regulator not fully connected Turn the coupling nut about one-half to three-quarters additional turn until solid
stop. Tighten by hand only - do NOT use tools
Obstruction of gas flow 1. Clear burner/venturi tube
2. Check for bent or kinked hose
Disengagement of burner to valve Re-engage burner and valve
Spider webs or insect nest in venturi Clean burner/venturi tube
Burner ports clogged or blocked Clean burner ports
Sudden drop in gas flow or reduced flame height
Out of gas Exchange, refill or replace LP gas tank
Overfilling prevention device may have been activated
1. Turn control knobs to “ OFF”
2. Wait 30 seconds and light griddle
3. If flames are still too low, reset the overfilling prevention device:
a. Turn control knob(s) “ OFF”
b. Turn LP gas tank valve to “CLOSED”
c. Disconnect regulator
d. Turn control knobs to (HIGH)
e. Wait 1 minute
f. Turn control knobs to “ OFF”
g. Reconnect regulator and leak check connections, being careful not to
fully open valve
h. Light griddle per “Lighting” section
Irregular flame pattern, flame does not run the
full length of burner Burner ports are clogged or blocked Clean burner ports
Flame is yellow or orange
New burner may have residual manufacturing oils Burn griddle for 15 minutes on (HIGH)
Spider webs or insect nest in venturi Clean venturi
Food residue, grease, etc. on burners Clean burner
Poor alignment of valve to burner/venturi tube Ensure burner/venturi tube is properly engaged with valve
Flame goes out
High or gusting winds Do not use griddle in high winds
Low on LP Gas Exchange, refill or replace LP gas tank
Overfilling prevention device may have been activated Refer to “Sudden drop in gas flow or reduced flame height” (see above)
Flare-up
Grease buildup Remove and clean all griddle parts per “Cleaning and Care” section
Excess fat in meat Trim fat from meat before cooking
Excessive cooking temperature Adjust to lower cooking temperature
Persistent grease fire Grease trapped by food buildup around burner system
1. Turn control knobs to “ OFF”
2. Turn LP gas tank valve to “CLOSED”
3. After griddle cools, remove and clean all parts per “Cleaning and Care”
section
Flashback (fire in burner tube(s)) Burner and/or burner/venturi tube are blocked Clean burners and/or burner/venturi tube
Griddle Surface
Griddle has started to rust
With use the griddle surface will rust, this is normal. Follow the “Refurbish the
Griddle Surface” instructions in the “Seasoning Griddle” section to season your
griddle surface.
Griddle surface looks dull The cooking surface has gotten too hot, and is no longer seasoned. Season grill
per “Seasoning Griddle” section.
For more assistance, please call 1.800.694.0013.