RCA Dual Alarm Clock with UVC Sanitizer Installation instructions

Dual Alarm Clock
with UVC Sanitizer
Let’s Get Started!

Plug in
1Load up the sanitizer
Plug the included power cable into the DC 5V jack
on the back of the clock/sanitizer.
Plug the other end into a power outlet or surge
protector.
Open the cover of the clock/sanitizer. Then place the item you want
to sanitize inside.
Charge up, too!
The clock/sanitizer can charge
your mobile device too! Just
plug your charging cable (not
included) into the charging
port inside the clock/sanitizer.
BATTERY BACKUP
Your clock has a pre-installed battery backup that will keep the
time in case power is interrupted (like by a power outage, for
example). If you notice that battery backup is no longer working,
simply replace the CR2032 coin-cell battery behind the circular
battery door in the sanitizing compartment. Use a coin to open the
battery door and access the CR2032 battery.
Set the time
Press and hold the button on the top of the clock/sanitizer until
the hours digits ash.
Use the +and —buttons on the top of the clock/sanitizer to adjust
the hour. Press to set.
Use the +and —buttons to adjust the minutes. Press to set.
Use the +and —buttons to choose 12- (AM/PM) or 24-hour time.
(12-hour time is the default.) Press to nish setting the time.
2
3

Sanitize!
Open the cover of the clock/sanitizer. Remove the item you
placed inside — it’s safe to use now!
4Get your clean stuff
5
Set the alarms (optional)
To set the time for alarm 1 ( ):
Press and hold the button on the top of the clock/sanitizer until the hours
digits ash on the display.
Use the +and —buttons on the top of the clock/sanitizer to adjust the hour.
Press to set.
Use the +and —buttons to adjust the minutes. Press to set.
To set the time for alarm 2 ( ): Follow the steps above, using the
button instead of .
To turn an alarm on/off: Press the button for the alarm you want to turn on
or off ( or ). The alarm time appears on the display and the indicator on
the display shows that you’ve turned that alarm on or off. Press the button
to display the current time.
6
Close the cover and choose the sanitization cycle you want to use.
For these items Use this cycle To start:
Hard, non-porous
(like phones, tablets, watches
and remote controls)
Standard cycle
(around 10 minutes) Press the button.
Fabric and soft porous (like
facemasks, toothbrushes, and
makeup brushes)
Deep clean cycle
(around 20 minutes) Press and hold the
button until the
indicator on the clock
display ashes twice.
The indicator on the clock display turns on during sanitization. It turns off
when the sanitization cycle is complete.
To stop sanitization before the cycle is complete: Press the button.
The indicator on the clock display ashes three times to indicate the
cycle has stopped and it’s safe to open the cover.
Notes:
• The indicator ashes if the cover is open when you try to start sanitization. For
your safety, the sanitizer cannot proceed with sanitization if the cover is open. Make
sure the cover is completely closed, then press the button again.
• You can use the deep clean cycle even for items that don’t need it. There’s no harm
done to the item—it just takes longer to nish the cycle.

Tour of the Dual Alarm Clock with UVC Sanitizer
DISPLAY
AM and PM indicators show if the time displayed is AM or PM in 12-hour time format.
indicator turns on when the sanitizer is in use. When it turns off, open the top and remove your items.
and indicators show if alarm 1 and/or alarm 2 are active.
indicator turns on when the backup battery needs to be replaced. See step 1 for details.
TOP AND SANITIZATION BAY
button lets you set the time (press and hold) or display the current time (press).
+ and – buttons adjust the ashing digits when setting the time or alarm.
SNOOZE button temporarily delays the alarm another 9 minutes until you turn it off. The alarm times out
after 1 hour if no buttons are pressed. To stop an active alarm, press any button except snooze. Note:
you cannot sanitize during an active alarm—if you press the button it stops the alarm. This button also
adjusts the display brightness.
button starts the sanitization process once the top is closed. You can choose the standard cycle (press) or
deep clean cycle (press and hold). Press this button during a sanitization cycle to stop the cycle before it’s com-
plete. The indicator ashes three times to indicate the cycle has stopped and it’s safe to open the cover.
and buttons let you set the alarm times (press and hold) or turn each alarm on/off (press).
The sanitization bay is where you put the item you want to sanitize. Once you’ve closed the top and
pressed the button, the item in the bay receives a bath of UVC rays that kill bacteria and viruses.
IMPORTANT: The UVC lights automatically turn off when the top of the bay is opened.
The charging port charges your mobile device when the clock/sanitizer is plugged in. Just plug your charging
cable into the port—your device charges both when the clock/sanitizer is sanitizing and when it’s not.
RCDS10 QSG 02
About UV sanitizing
Ultraviolet (UV) light is invisible to the human eye. The UVC part of the UV spectrum is proven to have germicidal benets, killing bacteria and deactivating
viruses. It is important to use the product with appropriate safeguards and follow safety precautions.
UV light is most effective on hard, non-porous surfaces such as phones, most phone cases, keys, credit cards, etc. UV light is less effective against fabrics
and other porous materials because of the many shadows they create that may block the UV light from hitting the surface. The UV light can only kill germs
on surfaces with which it comes in contact.
Sanitization bay
Charging port