RDI Titan Pro Rail STAIR RAIL User manual

STAIR RAIL
INSTRUCTIONS
RAILING DYNAMICS, INC.
FOR hOMe, FOR LIFe™
135 STEELMANVILLE ROAD
EGG HARBOR TOWNSHIP, NJ 08234
TEL: [phone]
FAX: [phone]
E-MAIL: [email protected]
URL: WWW.RDIRAIL.COM
NOTE: Check with your local building code office for design load requirements for
guard rails and bottom space requirements. All supporting structures should be built
in accordance with applicable building codes.
1.
Prepare all posts and mounting surfaces
before installation.
2.
Temporarily secure a plank on the noses
of the stairs between the posts onto
which you are installing the stair rail.
(Fig. 1) The thickness of the plank will
determine the space between the stairs
and the bottom rail.
Place the bottom rail, baluster routs
facing up, on the plank with the label
reading “This end top of stair.” at the
top post. Slide the rail up or down until
the rout spacing is even on each end
(Fig. 2).
Make a mark on each post to indicate
the upper surface of the bottom rail (Fig.
3).
(Fig. 1)
(Fig. 2)
(Fig. 3)

3.
Slide a bottom bracket cover onto each
end of the bottom rail, and temporarily
secure in place with tape. Position the
brackets covers so that once they are
cut a minimum of 1 1/8" of material is
left on the bottom of the bracket (Fig. 4).
Trace the posts onto the bracket
covers (Fig. 5).
Pencil in a mark 3/8" in from the ends
of the bracket covers which are closest
to the middle of the rail (Fig. 6). Now
loosen the tape, slide covers to the
marks you have made, and re-tape.
(You are performing this step in order to
allow space for the bracket thickness.)
Leave the bracket covers taped in
place and cut each end of the rail at
the lines you traced onto the bracket
covers (Fig. 7).
NOTE: Tape bracket covers closed in
order to prevent them from slipping
while cutting.
Tip:
If using a power saw, a carbide
tipped blade of at least 60 teeth is
recommended.
1 3/8" Minimum
(Fig. 4)
(Fig. 5)
(Fig. 6)
(Fig. 7)
(Fig. 8)
3/4"
(Fig. 9)
4.
Measure down 3/4" from the mark you
made on each post (Fig. 8). Place the
top edge of the aluminum brackets at
this mark on each post. Pre-drill and
attach brackets using supplied screws
(Fig. 9).
NOTE: The brackets that attach to the
top stair post are different from the
brackets that attach to the bottom
stair post. Top stair post installation is
depicted.
Repeat for bottom stair post.
Remove tape and bracket covers and
place bottom rail into attached alumi-
num brackets. Do not secure in place at
this time.

5.
Insert an uncrimped baluster into each
of the rst and last routs of the bot-
tom rail, and set the top rail in place by
inserting them into the corresponding
routs (Fig. 10). Place the top rail inside
of the posts to measure accurately.
Slide a top bracket cover in place at
each end of the top rail and temporarily
secure with tape (Fig. 11). Position the
bracket covers so that once they are cut
a minimum of 1 1/8" of material is left
on the bottom of the bracket (Fig. 12).
Adjust for plumb (Fig. 12).
Trace the posts onto the bracket covers
(Fig. 13).
Now repeat Step 3 using the top rail
by penciling in a mark 3/8" in from the
ends of the bracket covers which are
closest to the middle of the rail. Now
loosen the tape, slide covers to the
marks you have made and re-tape.
Leave the bracket covers taped in place
and cut each end of the rail at the lines
you traced onto the bracket covers.
NOTE: Tape bracket covers closed in
order to prevent them from slipping
while cutting.
6.
Remove tape and the top bracket cov-
ers. Insert a square baluster into each
rout of the bottom rail. Each kit contains
4 or 6 crimped balusters; space them
evenly in each section.
Set the top rail in place by inserting the
rst baluster (at the upper post) into the
corresponding rout of the top rail, and
work toward the bottom (Fig. 14).
(Fig. 11)
(Fig. 10) (Fig. 12)
(Fig. 13)
(Fig. 14)

(Fig. 20)
(Fig. 17)
(Fig. 18)
(Fig. 19)
TMPSI
MADE IN CHINA
7.
Hold the aluminum bracket in place on
the end of the rail; mark the bottom of
the aluminum bracket onto the post
(Fig. 15).
Push the rail aside. Pre-drill and attach
the aluminum bracket (Fig. 16). (Bottom
rail bracket installation depicted.)
Repeat at the top of the stair section.
Place the assembled rail section into
the four aluminum brackets and secure
with 2 set screws in each bracket (Figs.
17 and 18).
(Fig. 15)
(Fig. 16)
8.
Install bracket covers by wrapping them
around the rails and aluminum brackets.
Press the attachment tabs up into the
slots of the aluminum brackets (Figs. 19
and 20).
Snap trim rings around bottom ange
of support post. Attach post cap, sold
separately, using vinyl adhesive.