Ready2Talk PA 64 User manual

PA 64
Installation & Operation Manual
The PA for ALL applications!

IMPORTANT!
Please read all these key points to ensure the proper
connection and designed use of your PA 64. If you
ha e ANY questions, please call 1 888 724-5351
before proceeding!
•Basically, the PA 64 is an amplifier that is connected between the
stereo’s output and the vehicles spea ers!
•DO NOT connect the vehicles spea er wires to the stereo’s
output as well as the PA 64. Remember point one… the PA 64
goes between the stereo and the spea ers!
•The PA 64 is an amplifier and is NOT designed to be used with
ANY other amplifiers (e.g. being connected between the stereo
and amplifier). If done, the PA 64 will not function and it may
damage the PA 64 and / or the additional amplifiers. If you need
more amplification than the PA 64 offers, we have other PA
options to suit. Please just give us a call.
•The PA 64 is intended to be installed by a professional installer,
service mechanic, vehicle dealer or manufacturer. Do not
attempt to install this unit without confirming compatibility to
your vehicle with the manufacturer or dealer. Failure to do so
may cause damage to the PA 64, your vehicles electrical system
or void your vehicle warranty.
•Only use with Ready2Tal microphones… use of any others may
cause damage.

Now with the important warnings out of the way…
The PA 64 is designed to be the best unit for all applications, offering
a real amplifier with 4x50Watts (pea ), solid state mic / stereo
switching and variable muting for both the rear RCA input and the
front 3.5mm AUX input.
It also allows the use of two microphones, hand or headset, wired or
wireless; and is the perfect PA system for Sightseeing, Shuttle,
Transit, School Bus, Church Busses, Retirement Homes, People
Movers, Boats, Trolleys, Snow Cats and Horse Carriages. Did we
forget anything? Oh yes… also an easy replacement for older PA
systems in Highway Coaches.
Use the PA 64 as a standalone PA system or in conjunction with your
factory (OEM) stereo or any aftermar et stereo / DVD player or
automated tour system by using the internal High / Low impedance
selector. Don’t forget you can connect your MP3 player though the
front AUX input.
The PA 64 can be mounted on any flat surface vertical or horizontal
and includes an optional front decal so the printing will always be the
right way around. We try to thin of everything.
Want to hide it away? There is an optional RMK (Remote Mounting
Kit) and a RME (Rear Mic Extension) for a second mic when using a
step on guide.
Easy to connect, easy to use and is better sounding than any other PA
you’ve heard before. Finally, you too can sound li e a radio DJ.
*sound effects and annoying side ic not included.

Stereo Connection Options
Diagram 1 – Connection to Aftermarket Stereo RCA Output
Note: Set Input Switch on PA 64 to “Low”
Note: When using RCA cables the stereo’s spea er wires are not
connected to the PA 64 or the spea ers.
Diagram 2 - Connection to OEM Factory Stereo Speaker Wires
Use RCA to spea er wire pig tails included in the box.
Note: Set Input Switch on PA 64 to “High”
Note: Rear spea er wires from the stereo are not connected

PA 64 Multi Pin Plug Wiring Code
12V + Battery Yellow
12V + Switched Red
12V – Ground Blac
Right Front + Gray
Right Front - Gray / Blac
Left Front + White
Left Front - White / Blac
Right Rear + Purple
Right Rear - Purple / Blac
Left Rear + Green
Left Rear - Green / Blac
Additional Wiring Info
Yellow 12V + Constant power - 10 Amp fuse in the plug base
Red 12V + Accessory power – Internal automatic re-settable fuse
Note: Never increase the value of the fuse as damage may occur.
Note: The 4 x 50 Watt amplifier inside the PA 64 is designed to
accommodate a 4 – 8 Ohm floating spea er load.
Note: DO NOT EXCEED a 4 – 8 Ohm spea er load! If spea er load
is outside intended range, the PA 64 will blow the 10A power fuse
after a short time.
Note: The PA 64 amplifier uses a floating output. Please ensure
your spea ers are not common grounded or connected to the vehicle
ground as damage will occur to the PA 64 and repairs / replacement
will not be covered by warranty.
Note: All “Spea er Connection Options” are based on the use of 4
Ohm spea ers and these diagrams will offer a load range from 4 – 8
Ohm to the PA 64 amplifier. If in doubt… please call 1 888 724-5351

Speaker Connection Options - Based on 4 Ohm Speakers
Normal 4 Speaker Option
Cutaway Bus 6 Speaker Option Using Dri ers Speakers
Cutaway Bus 8 Speaker Option with Door Speakers

Bus 8 Speaker Option
Bus 10 Speaker Option

Bus 12 Speaker Option
Bus 16 Speaker Option

Testing your PA 64
1. Connect your microphone to the “Mic 1” on the front of the PA
64 and / or “Mic 2” on the bac .
2. Turn on the vehicle, then the PA 64 power switch (the power
light will come on), turn on the microphone and tal in to the
mic. Adjust the mic volume with the “Volume” control on the
front of the PA 64 to your desired volume.
3. Turn off the mic and turn on the stereo, adjust the radio volume
as normal to desired level.
4. Turn the “Audio Mute” control on the front of the PA 64 to half
way / 50%. (nothing will happen yet)
5. Turn bac on the mic and the radio volume will mute to 50% of
what you just set. Turn the mic off and the radio will come bac
up to full volume automatically.
6. You can adjust the amount of muting by turning the “Audio
Mute” control on the front of the PA 64. Full left = no muting,
full right = 100% muting.
7. When playing music from your MP3 player through the front
“AUX input”, the muting will function the same as listed above in
point #5.
Note: With the mic switch in the OFF position the front controls on
the PA 64 will not function. This is normal.
Note: When connecting your MP3 player into the front “AUX input”
the sound will blend together with the stereo. It’s recommended to
turn off the stereo when using the “AUX input” so they don’t compete.

Options - Making the PA 64 “the PA system for ALL applications”
Optional Front Decal Depending on your vehicle, it may be best to mount the
PA 64 either vertically or upside down. We have included an additional front
label that is reversed which allows the printing to show the correct way.
RMK (Remote Mount Kit) A small flush mounted plate with a 4 pin mic and
3.5mm AUX input soc et and cables that connect to the front mic and AUX
soc ets allowing you to hide your PA 64 for a custom loo . Available in two
versions RMK (5ft.) & RMK-15 (15ft.)
RME (Rear Mic Extension) A small flush mounted plate with a 4 pin mic soc et
and 15 ft. cable that connects to the bac of the PA 64 and offers a second mic
input when you want to have a step on guide.
Hand Microphones
HM BT2 Digital wireless headset that offers over 30 ft. range and 12 hrs.
continuous operation between charges, but charges fully in 6 hrs.
PHM 6C Standard Push to Tal hand mic (PTT) with rubber curly cord
HM 2C Durable singers style hand mic with 12 ft. mic cable
Headset Microphones
HS BT2 Digital Wireless Headset that offers over 30 ft. range with 8 hrs.
continuous operation between charges, but charges fully in 4 hrs.
HS 30M Lightweight but durable condenser headset microphone with inline
On/Off switch with the wire and boom on LEFT side
HS 40M Same as HS 30M except with switch wire and boom on RIGHT side
Gooseneck Microphone
GN 17R 17” Condenser goosenec mic with a dual function (latching and
momentary on) dash mounted roc er switch
GN 17F 17” Condenser goosenec mic with a durable foot switch

For more information
Find us at
www.ready2talkpa.com
or give us a call at
1 888 724-5351
Double E Products Ltd .
Box 16118 / 1199 Lynn Valley Rd
North Vancouver BC V7J 3S9 Canada
1 888 724-5351
www.ready2tal pa.com info@ready2tal pa.com