Real Franklin Autoswing User manual

AUTOMATIC OPENER SYSTEM FOR OUTSWING RESIDENTIAL GARAGE DOORS
Exclusively by:
Installation Manual

THIS PAGE INTENTIONALLY LEFT BLANK

TM
Franklin Autoswing Installation Manual
3
© 2013 Copyright Real Carriage Door Company, Inc.
Thank you for buying this product, our company is sure that you will be more than
sased with the product’s performance. The product is supplied with
a “Warnings” leaet and an “Instrucon booklet”. These should both be
read carefully as they provide important informaon about safety, installaon,
operaon and maintenance. This product complies with the recognized
technical standards and safety regulaons.
1) GENERAL OUTLINE
The LIBRA-UL-R control panel is supplied by the manufacturer with standard
seng. Any alteraon must be set by means of the incorporated display
programmer or by means of UNIPRO. The Control unit completely supports
the EELINK protocol. Its main characteriscs are:
- Control of two low-voltage motors up to 40W power
- Electronic torque seng with obstacle detecon
- Limit-switch control inputs
- Separate inputs for safety devices
- Incorporated rolling-code radio receiver with transmier cloning
The IGEA-BT (24V) is suitable for residenal use and has
been designed for swing gates with parcularly large gate posts. The drive
arm, built with a special an-shearing shape, allows the leaves to be moved
when the controller is considerably out of place with respect to the fulcrum
of the leaves. The non-reversible electro-mechanical motor maintains the stop
during closing and opening. The release knob with personalized key, ed outside
each operator, makes manual operaon extremely easy.
2) SAFETY
If correctly installed and used, this automaon device sases the required
safety level standards. However, it is advisable to observe some praccal
rules in order to avoid accidental problems. Before using the automaon device,
carefully read the operaon instrucons and keep them for future reference.
• Keep children, persons and things outside the automaon working area,
parcularly during operaon. An incorrect installaon or improper use of the
product can cause damage to persons, animals or things.
• Keep radio control or other control devices out of children’s reach, in order to
avoid any unintenonal automaon acvaon.
• Do not intenonally oppose the leaf movement.
• BFT declines all responsibility for any consequences resulng from failure to
observe Good Technical Pracce when construcng closing structures (door,
gates etc.), as well as from any deformaon which might occur during use.
• The installaon must comply with the provisions set out by the following
direcves: 89/336/CEE, 73/23/EEC, 98/37/EEC and subsequent amendments.
• Do not aempt to open the gate by hand, if the actuator has not been released
by means of the appropriate release knob.
• Do not modify the automaon components.
• In case of malfuncon, disconnect the power supply, acvate the emergency
release to gain access to the actuator and request the assistance of a qualied
technician (installer).
• Before proceeding to any external cleaning operaon, disconnect the main
powers supply and at least one of the baery pole, if ed.
• Check that grounding is carried out correctly: connect all metal parts for closure
(doors, gates etc.) and all system components provided with an earth terminal.
• Fit all the safety devices (photocells, electric edges etc.) which are needed to
protect the area from any danger caused by squashing, conveying and shearing,
according to and in compliance with the applicable direcves and technical
standards.
• Keep the photocell opcal components and luminous signal indicaon devices
clean. Check that the photocells are not obscured by branches or shrubs.
• For any direct assistance to the automaon system, request the assistance of a
qualied technician (installer).
• Have qualied personnel check the automaon system once a year.
• Entrance is reserved for vehicles, provide a separate entrance for pedestrians.
3) SCRAPPING
Warning: This operaon should only be carried out by qualied personnel.
Materials must be disposed of in conformity with the current regulaons. In case of
scrapping, the automaon devices do not entail any parcular risks or danger. In
case of materials to be recycled, these should be sorted out by type (electrical
components, copper, aluminum, plasc etc.).
4) DISMANTLING
Warning: This operaon should only be carried out by qualied personnel. When
the control unit is disassembled to be reassembled on another site, proceed as
follows:
• Disconnect the power supply and the enre electrical installaon.
• In the case where some of the components cannot be removed or are damaged,
they must be replaced.
5) FUNCTIONS
FOR THE INSTALLER: Fill in the table with the parameters set, in order to facilitate
future modicaons and maintenance operaons. The preset values are indicated
between square brackets [ ].
PARAMETER MENU
Automac Closing Time [10s] ___
Motor 1 torque [50%] ___
Motor 2 torque [50%] ___
Motor 1 slow-down torque [45%] ___
Motor 2 slow-down torque [45%] ___
Opening delay me [1s] ___
Closing delay me [1s] ___
Motor 1 Normal Speed Time [15s] ___
Motor 2 Normal Speed Time [15s] ___
Slow-down speed [0] ___
Zone [0] ___
LOGIC MENU
TCA (Automac Closing Time) [OFF] ___
3 steps [OFF] ___
Impulse lock on opening [OFF] ___
Rapid closing [OFF] ___
Photocells on opening [OFF] ___
Photocell test [OFF] ___
No. motors in operaon [OFF] ___
Lock hold [OFF] ___
Start / Close [OFF] ___
Fixed code [OFF] ___
Radio programming [ON] ___
Master [OFF] ___
WARNINGS
Correct controller operaon is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulng from failure to observe the
installaon standards and the instrucons contained in the present
manual.
The descripons and illustraons contained in the present manual are
not binding. The Company reserves the right to make any alteraons
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essenal product features
unchanged, at any me and without undertaking to update the
present publicaon.
ATTENTION! The IGEA-BT model controller is not equipped with mechanical
torque adjustment. It is compulsory to use a control panel of the same
manufacturer, in compliance with the basic safety requirements of direcves
73/23/CEE, 89/336/CEE, 89/37/CEE equipped with appropriate electric
adjustment of the torque.
Correct controller operaon is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulng from failure to observe the
installaon standards and the instrucons contained in the present
manual.
The descripons and illustraons contained in the present manual are
not binding. The Company reserves the right to make any alteraons
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essenal product features
unchanged, at any me and without undertaking to update the
present publicaon.

Franklin Autoswing Installation Manual
TM
4 © 2013 Copyright Real Carriage Door Company, Inc.
General Informaon
Technical Specicaons 5
Manual Operaon Mode 6
Typical System Overview 7
Motor Installaon 8-9
Limit Switch Installaon 10
Mounng the Control Housing 11
Wiring the Motor 11
Master Wiring Diagram 12
General Programming 13
Installing the Motor Cover 14
Appendices
Programming the Remotes 15 (Appendix A)
Oponal Baery Backup 16 (Appendix B)
Door Top Radius Table 17 (Appendix C)
Alternave Mounng 18 (Appendix D)
Oponal Accessories 19 (Appendix E)
For all programming parameters, please refer to the following BFT product manuals:
LIBRA-UL-R Control Panel
Manual last revised 7/7/2015
Table of Contents
The table of contents are listed to assist you locang a desired secon. We do however
strongly suggest reading the enre instrucon manual before aempng installaon. Note
that this manual is for outswing garage doors. IMPORTANT! This installaon manual is
designed as a supplement to the BFT product manuals. Be sure to read the safety
informaon in all product literature associated with this opener system, as well as comply
with all of the specicaons they contain.

TM
Franklin Autoswing Installation Manual
5
© 2013 Copyright Real Carriage Door Company, Inc.
MODEL: FRANKLIN (IGEA-BT)
Mounng Clearance 7.5" above lowest part of door jamb
Voltage 24 V
Power supply 120 V 60 Hz single-phase
Absorbed power 0.05 hp (40 W)
Opening or closing me 15 s
Impact reacon Torque limiter on control panel
Manual release Release knob with personalized key
Operang cycle Intensive Use
Environmental condions 5oF to 140oF
Degree of protecon IP44
Operator Weight 35 lbs
Door leaf max length Up to 10 
Door leaf max weight Up to 550 lbs
Door leaf max surface area 120 2
Maximum open angle Up to 125o
Specicaons
14 1/16” 7 1/4”
6”

Franklin Autoswing Installation Manual
TM
6 © 2013 Copyright Real Carriage Door Company, Inc.
Manual Operaon Mode
NOTE: When working with limit switches, the
key cannot be used to manually release motor.
To release, ip the black lever (pictured at
right) and swing the door. The lever must be
held down while swinging as it is spring loaded.
Right Motor Le Motor
Inside
Outside
For LEFT motor (as viewed from inside):
1. Turn key clockwise
2. Turn release knob counter-clockwise
3. Turn key back to keep in release posion
4. Push/pull door slowly to open or close
5. Reverse steps to re-acvate auto-mode
For RIGHT motor (as viewed from inside):
1. Turn key clockwise
2. Turn release knob clockwise
3. Turn key back to keep in release posion
4. Push/pull door slowly to open or close
5. Reverse steps to re-acvate auto-mode
In the case of power failure or operator malfuncon, manual operaon mode can be carried out
by turning the external release knob with personalized key.

TM
Franklin Autoswing Installation Manual
7
© 2013 Copyright Real Carriage Door Company, Inc.
Typical System Overview
Below is an example of typical component placement and wiring. Please note that the Control Housing
must have holes drilled into it to run the wires. UL Listed stress-relief connectors are recommended. Be
careful not to damage the panel when drilling into the housing! It is a good idea to remove the panel
while drilling. Refer to “Master Wiring Diagram” for more detailed views of Control Panel connecons.
Surge protecon and a dedicated circuit are encouraged.
*Motors are low voltage. Use braided wire.
Increase wire gauge if motors mounted
more than 20’ from control housing.
**From lowest part of jamb to ceiling line.
A. Control Housing (dims 7.25” x 8.75” x 3.5”)
B. Left Motor
C. Right Motor
D. Receiver Photoeye
E. Transmitter Photoeye
F. Wall Pushbutton
G. 4-Button Remote Transmitter (2)
H. Antenna (for extra range applications)

Franklin Autoswing Installation Manual
TM
8 © 2013 Copyright Real Carriage Door Company, Inc.
1. Remove the cover to the motor and set aside.
2. Remove the motor from the base plate by loosening the 4 bolts on the boom of the motor.
3. Posion the base plate (note that body of the motor should extend toward the side jamb) about 7” from the edge
of the door*. Level the plate and mark the locaons of the holes. TIP: For most applicaons, centering the boom
row of holes on the jamb makes for the most secure installaon.
Le base plate posion, square-top
door (interior view)
Installaon of Motor
TIP: Before mounng, refer to “Typical System Overview” for prewiring. For a very ‘clean’
installaon, mount the unit directly on the head casing (if at prole). Note that this motor
posioning is for outswing doors only.
4. Level and mount the plate with minimum 3/8” x 4” lag bolts (not supplied). For proper arm clearance, the boom
of the plate must no higher than the lowest part of the jamb. Always make certain that the lag bolts penetrate solid
header and/or blocking material.
5. Re-aach the motor to the base plate and ghten securely. Be sure that the motor is seated properly in its plasc
housing.
*NOTE: There are limitaons for certain arch-top radii relave to the door width. See table in
APPENDIX C for allowable radii, and APPENDIX D for more help in posioning.
Le base plate posion, arch-top
door (interior view)
7”
7”

TM
Franklin Autoswing Installation Manual
9
© 2013 Copyright Real Carriage Door Company, Inc.
6. Assemble the arculated lever arm and door coupling as shown in g. 1. Connect straight arm and door coupling to
curved arm using plasc sleeve (K) and washer (L). Secure together with rolled pin (M). The dashed arm indicates
the setup for the right motor (viewed from inside).
7. Slide the assembled arm onto the transmission sha at the base of the motor, and fasten it using the long pin (N)
and C-ring (O).
8. Manually release the operator (See “Manual Operaon Mode”).
9. Open the door to the desired ‘fully open’ point (approx 105 degrees is recommended). With a measuring tape,
mark the centerline of the door mounng bracket at 40” from the center of the sha (g. 2). Making sure that the
arm is level, Mount the arm to the door with #14 x 1-1/2” pan head screws (not supplied)
10. Check clearance and movement by swinging door slowly.
11. Relock the motor (take out of manual release mode).
12. Repeat these steps for the other leaf, if installed.
Installaon of Motor (Connued)
Fig 1. Arm Assembly Fig 2. Arm posioning
K
L
M
N
O
NOTE:
1.5” dimension is an
approximation only

Franklin Autoswing Installation Manual
TM
10 © 2013 Copyright Real Carriage Door Company, Inc.
Installaon of Limit Switches
1. Install the limit-switch refernce cams as
shown in g. 3. Install the full cam on top of
the metal sha, then install the ring cam on
top of the full cam. Do not fully ghten the
xing screws.
2. When the door is fully open, rotate the
corresponding cam (g. 4), unl you hear a
‘click’ indicang the limit switch has been
depressed, then lock it in posion by
ghtening the appropriate screws. Repeat for
the fully closed posion. Refer to “Manual
Operaon Mode” to manually swing the door.
3. Swing the door slowly to its open and close
posions, listening to see that the ‘click’ of
the limits switch occurs where desired. Note
that the le motor’s cams (close vs open) are
inverted from those of the right motor.
Adjust as necessary.
Fig 4. Limit Switch funcons
LEFT MOTOR
(viewed from inside)
RIGHT MOTOR
(viewed from inside)
CLOSE LIMIT CAM
OPEN LIMIT CAM
CLOSE LIMIT
SWITCH
OPEN LIMIT
SWITCH
OPEN LIMIT CAM
CLOSE LIMIT CAM
OPEN LIMIT
SWITCH
CLOSE LIMIT
SWITCH
Fig 3. Limit Switch installaon
FULL CAM RING CAM

TM
Franklin Autoswing Installation Manual
11
© 2013 Copyright Real Carriage Door Company, Inc.
1. Locate the control housing containing the LIBRA-UL-R panel.
2. For mounng, the rear of the housing must be predrilled. Refer
to g. 5 for the locaons of the holes to be drilled.
3. At this me, plan where you would like to run the wiring into
the housing and predrill for stress-relief connectors. NOTE! Be
careful not to damage the panel when drilling into the
housing! It is advisable to remove the panel while drilling.
4. Mount the housing securely, using either screws or drywall
anchors (not supplied). Be careful not to damage any wires or
components of the board. (See “Typical System Overview” for
suggested locaon of the housing)
Mounng the Control Housing
Fig 5. Mounng locaons
Fig 6. Stress relief connector
1. Locate the stress relieving cord-grip.
2. Aach connecng nut (F) to grip body (G). Tighten securely
using nger pressure only.
3. Slip compression nut (H) over a length of 16/3 (16 Gauge,
3 strand) motor wire and thread wire through the
assembled cord-grip.
4. Tighten the compression nut (H) with nger pressure only.
5. Refer to “Master Wiring Diagram” to wire the motor to the
LIBRA-UL-R control panel.
6. For basic programming see “General Programming.” For
advanced parameters, please see the BFT “LIBRA-UL-R
Installaon and User’s Manual”
Wiring the Motor
F
G
H
WIRE USE
min 16/3 wire* connecng motors to control panel
min 22/4 wire connecng RX photoeye to control panel
min 22/2 wire connecng TX photoeye to control panel
*Use stranded wire. Increase gauge if motors more than 20’ from panel

Franklin Autoswing Installation Manual
TM
12 © 2013 Copyright Real Carriage Door Company, Inc.
Master Wiring Diagram Note:
The antenna is not
necessary for normal
operaon. Use as a signal
booster for long range or
thick masonry walls.
Important Note:
The wiring shown will acvate the le door opening rst
(viewed from inside). If you require the right door to open
rst, swap wires 3&6, 4&7, and 5&8 at the control panel.
It is advised to wire the system and test operaon before
installing photoeyes.
Important Note:
Jumper between
terminals 15 and 18 must
be removed aer adding
photoeyes. The jumper
from 15 to 17 remains.
Test operaon before
installing photoeyes and
removing jumper.
Important Note:
Use of surge protecon and a
dedicated circuit is encouraged
to protect the system from
harmful uctuaons in current.
Terminals may be hardwired or
installer may wire a ‘pigtail’
cord into terminals.
GROUND
LINE IN
NEUTRAL
BLK
GRN
WHT
GRN
BLK
WHT
LEFT MOTOR / DOOR
RIGHT MOTOR / DOOR
PHOTOEYES
WALL
SWITCH
CO-AXIAL SHEILD
ANTENNA CORE
22 Ga. minimum
22 Ga. minimum
16 Ga. Minimum
(stranded)
Increase wire
gauge if motors
more than 20’
from Control Panel
14 Ga. Minimum
120VAC
POWER
Important Note:
With the photoeyes installed,
the door system should stop
and reverse if obstructed
when closing. If the system
reverses when obstructed
when opening, double check
the motor wiring at le.
Photoeye fault is indicated by
‘PhOt’ on the LCD display.
Adjust the eyes unl the fault
code clears.
Note: Terminal strip JP8 (No’s
3-20) is ‘press t’ and may be
removed for ease of wiring.

TM
Franklin Autoswing Installation Manual
13
© 2013 Copyright Real Carriage Door Company, Inc.
General Programming
The Franklin Autoswing comes “out of box” with preprogrammed defaults that allow the unit
to funcon without further programming needed. There are, however a few steps that can
increase the degree of safety and exibility of the system. For a list of all programming
parameters, see the “LIBRA-UL-R Installaon and User’s Manual” pages 13-17.
AUTOSET
Automacally adjusts the torque to the minimum required to operate the door. NOTE: Before you
use this seng, you MUST have the system fully operaonal and stopping at its limits in the proper
place, etc.
Programming is as follows:
Press “OK” buon twice
Scroll with minus (-) buon down to “AUtoSEt”
Press “OK” to acvate.
Once acvated, the door will execute an opening maneuver, followed by a
closing maneuver. NOTE: DO NOT obscure photoeyes or give any open/stop
commands during this phase. Upon successful compleon, the display will read
“OK”. If “KO” is displayed instead, Autoset was not successfully programmed.
Manually check the operaon of the door, as well as check the limit switches,
before execung Autoset again. Press minus (-) and plus (+) together to exit to
preceding menu, repeat unl the display switches o.
WARNING! During the Autoset phase, obstacle detecon funcons are not
acve, so the installer must control the automaon movement and prevent
people or things from entering the working range of the doors. For emergency
shutdown, pull the main fuse located above the 120V terminal.
Main Fuse
CLOSING DELAY TIME
Allows user to set the operaonal closing delay between Motor 1 and Motor 2 between 1 and 10
seconds (default is 1 second). Useful if the door that opens rst is limited in how wide it can open with
respect to the other door.
Programming is as follows:
Press “OK” buon three mes
Scroll with minus buon down to “cLS dELAy tIME”
Press “OK” to enter menu
Press minus (-) for less delay, plus (+) for more delay (max 10 seconds)
Press “OK” to conrm
Press minus (-) and plus (+) together to exit to preceding menu, repeat unl the display switches o.

Franklin Autoswing Installation Manual
TM
14 © 2013 Copyright Real Carriage Door Company, Inc.
Installing the Motor Cover
1. Hold the cover over the motor, with the front of the cover angled toward you. Rock the cover rearward (g. 7) unl
the cover is seated. The cover must be installed in this way so that the Manual Operaon cam engages properly
with motor (g 8).
2. Test the manual release mechanism as described in “Manual Operaon Mode.”
3. Fasten the cover with the 4 screws provided (g. 9).
Fig 8. Manual Operaon Cams
Fig 7. Seang the cover
Fig 9. Securing the cover
LEFT MOTOR CAM
RIGHT MOTOR CAM

TM
Franklin Autoswing Installation Manual
15
© 2013 Copyright Real Carriage Door Company, Inc.
1. Press “OK” buon twice Turn on the display
2. Scroll with minus buon (-) down to “rAdio”
3. Press “OK” (the display will read “Add StArt”)
4. Press “OK” (the display will read “hIddEn bUtton”)
5. Press and hold the hidden buon on the transmier (see g. 10) unl the display reads “rELEASE”
6. Release the hidden buon (the display will read “dESIrEd bUtton”)
7. Press the buon you want to acvate the door with (the display will read “ok 01”, “ok 02”, etc)
8. The display will now read “Add StArt”, repeat the procedure from step # 4 to install other transmiers.
9. Switch o the display by simultaneously pressing “+” and “-” buons twice. Your transmiers are now ready to
use.
Appendix A
(Programming the Remotes)
Fig. 10 Hidden Buon
On 4-buon remotes, the hidden buon
is acvated by pressing the two forward
buons closest to the LED at the ‘front’
of the remote.

Franklin Autoswing Installation Manual
TM
16 © 2013 Copyright Real Carriage Door Company, Inc.
Appendix B
(Oponal Baery Backup)
1. Secure the baery housing to solid blocking using screws or lag bolts (not provided)
2. Wire the baeries into the terminal strip using 14 ga. (minimum) wire in series as shown below, taking care to
observe polarity.
3. Splice terminal 3 to the wire that connects “0V” on the transformer to “JP2” on the LIBRA-UL-R panel. Always use
UL listed electrical connecve devices.
4. Remove the connector between “25V” on the transformer and “JP5” on the LIBRA-UL-R panel.
5. Connect terminal 4 to “25V” on the transformer.
Baeries

TM
Franklin Autoswing Installation Manual
17
© 2013 Copyright Real Carriage Door Company, Inc.
Appendix C
(Door Top Radius Table)
Use the chart below to determine if your arched door can be automated with the
Franklin Autoswing™.
Double Door
Width (ft-in)
Minimum
Radius (in)
Max Segment
Height*(in)
6' 0" 90" 7-1/2"
6' 6" 97-1/2" 8-1/8"
7' 0" 105" 8-3/4"
7' 6" 112-1/2" 9-3/8"
8' 0" 120" 10"
8' 6" 127-1/2" 10-1/2"
9' 0" 135" 11-1/4"
9' 6" 142-1/2" 11-7/8"
10' 0" 150" 12-1/2"
10' 6" 157-1/2" 13-1/8"
11' 0" 165" 13-3/4"
11' 6" 172-1/2" 14-3/8"
12' 0" 180" 15"
12' 6" 287-1/2" 15-5/8"
13' 0" 195" 16-1/4"
13' 6" 202-1/2" 16-7/8"
14' 0" 210" 17-1/2"
14' 6" 217-1/2" 18-1/8"
15' 0" 225" 18-3/4"
15' 6" 232-1/2" 19-3/8"
16' 0" 240" 20"
*This is the vertical distance from the springline to
the peak of the arch

TM
Franklin Autoswing Installation Manual
18
© 2013 Copyright Real Carriage Door Company, Inc.
Appendix D
(Alternave Mounng)
1. Fashion a plywood or cardboard disk that you can use
as a template. The disk should be 8” in diameter, with
a 1-7/8” diameter hole cut out of the center.
2. Set the disk on your assembled lever arm as show
below. You will not need the motor or base plate. With
your door leaf in the fully open posion (approx 105
degrees), move the disk along the wall and door
coupling along the door unl you achieve the
dimensions at right. For best results, the straight leg of
the lever arm should be as close as possible to the
arched jamb (1/2” min) .
3. Mark the center point of the bracket on the door and
the tangent point of disk on the wall.
4. Drop the motor into the base plate and hold on wall at
ancipated mounng locaon. Dry t the lever arm
and adjust height of enre assembly as necessary for
proper arm clearance when fully open.
5. Mark the height of base plate. Mount the plate as
described in “Installing the Motor,” and connue with
normal installaon.
NOTE: Securely mounng the base plate is very
important. If needed, drill addional mounng holes
to ax the plate directly to the jamb.
Disk
Lever arm
With some arched doorways, proper motor posioning
can be a lile challenging. Door construcon, radius,
and overall width can all aect motor placement. Below
is a guide designed to assist you in mounng while
allowing for proper geometry of the opener system’s
arculated lever arm.

Franklin Autoswing Installation Manual
TM
19 © 2013 Copyright Real Carriage Door Company, Inc.
Appendix E
(Oponal Accessories)
Wireless Wall Button
This upgraded wall button is wireless, so no wiring is
necessary for installation. Operates up to 4 doors.
Wireless Outdoor Keypad
With an outdoor keypad you enjoy secure exterior access
to your doors without a remote. Operates up to 10 doors.
Battery Backup
Be prepared for unexpected power outages with a battery
backup. Dimensions 7.75” x 9.25” x 3.75”. Battery Backup
powers one Franklin system only.
ECOSOL Solar Power
Get your garage door off the grid with Ecosol solar
conversion. Allows up to 3 weeks of residential use without
sunshine. Optional accessory can charge batteries from line
voltage.
HOMELINK Compatibility
Toss out your handheld remote controls and operate your
garage door system directly from your car with the
Homelink compatibility option.
®

For questions,
please contact us for technical support
800-694-5977
9803 44th Avenue NW, Gig Harbor, WA 98332
TM