Rebelle CYL-003 7600T LED Series User manual

www.rebellelighting.com
© 2017 REBELLE All rights reserved. REBELLE ARCHITECTURAL LIGHTING 11475 - 201AStreet, Maple Ridge, B.C. Canada V2X 0Y3
P604.465.5739 F 604.465.9801 E [email protected] Wrebellelighting.com
1
2
3
4
5
6
7
8
ARM INSTALLATION INSTRUCTIONS
CYL-003 7600T LED Series
Remove arm assembly from shipping carton and lay out parts.
Position mounting plate over junction box, pull supply leads through access hole in wall plate. Install wall plate, independent of junc-
tion box, with (4) mounting bolts (not supplied). Mounting bolt size and backing to be determined by installer per installation.
Attach arm assembly by connecting (3) leads provided (black, white & ground) to supply leads with appoved wire connectors and
push connections into junction box. Hook arm assembly over wall plate and secure with (2) set screws located at bottom of mounting
plate.
Remove (3) screws securing wiring access plate and remove access plate. Pull (3) leads (black, white & ground) through bottom of
access plate opening.
Feed (3) leads attached to fixture assembly through arm assembly and out bottom of wiring access hole. Slide fixture assembly over
arm assembly and attach per fixture instuctions.
Connect (3) sets of leads with approved wire connectors and push connections up into arm assembly. Reinstall wiring access plate.
Follow fixture installation instructions to complete installation (see following page).
Energize and test as required.
IMPORTANT
Disconnect power before installing fixtures. Read instructions before
starting work. This product must be installed in accordance with the
applicable installation code by a person familiar with the construction
and operation of the product and the hazards involved.
REV. 11/27/17
Fixture Assembly
Arm Assembly
Wiring access plate
Mounting bolts
(by others)
Junction box
(by others)
Wall plate
Mounting plate
Note:
Reflector is to face
away from wall
Arm

www.rebellelighting.com
© 2017 REBELLE All rights reserved. REBELLE ARCHITECTURAL LIGHTING 11475 - 201A Street, Maple Ridge, B.C. Canada V2X 0Y3
P604.465.5739 F 604.465.9801 E [email protected] Wrebellelighting.com
1
2
3
4
5
6
7
FIXTURE INSTALLATION INSTRUCTIONS
CYL-003 7600T LED Series
Remove luminaire from shipping carton and lay out parts. (housing assembly, shade assembly, arm assemblies & parts bag)
Place shade assembly (top down) on flat surface. Make sure (3) universal joints connections (on shade assembly) are loose enough
so that they can be turned by hand for adjustment at step 4.
Place housing assembly on flat surface (fitter end down). Thread (3) arm assembies to housing assembly. Tighten arms with 5/8”
wrench at top end of arm assembly. Universal joints at top of arm assemby should still be loose enough to turn by hand.
Position housing assembly/arm assembly over shade assembly (see bottom view) Align and connect universal joints (see fig. 2)
using cap screws and hex nuts (provided in parts bag)After housing assembly / arm assemblies are joined tighten cap screws holding
universal joints to shade assembly.
Connect fixture leads to supply leads and secure as required. Position fixture over pole (see exploded view) making sure fitter slides
to bottom. Tighten 5 set screws attached to fitter evenly making sure fixture is aligned vertically.
To secure luminaire to pole drill remaining hole in fitter (see exploded view) through into pole. Drill 0.250” dia. hole and insert 1/4x1”
split pin (provided in parts bag) through fitter and into pole until pin is flush with fitter. Alternately drill 0.201” dia. through into pole and
tap 1/4-20 , thread 1/4-20x1” set screw (provided in parts bag) through fitter and into pole. (Anti-rotation stop)
Energize and test as required.
IMPORTANT
Disconnect power before installing fixtures. Read instructions before
starting work. This product must be installed in accordance with the
applicable installation code by a person familiar with the construction
and operation of the product and the hazards involved.
REV. 11/27/17
Front View
Bottom View
Figure 1
Shade w/ universal joints
1/4-20 cap screws w/locking nut
Exploded View
Shade assembly
Housing assembly
Arm (3) assembly
Figure 2
Universal joints
Arm
Housing
Split pin or 1/4-20x1" set screw
1/4-20x1/2" set screws
Pole (see pole guide) or Arm
assembly (for 7600T)
Fitter
Machined for 5/8" wrench