RectorSeal AG-4200E User manual
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THEACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVEAND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
In HVAC Unit locate H
A. Connect “RED”, “Input 24 VAC (Hot)” and “Gray” “Common” wire of AG-4200E to 24
VAC (Hot) secondary side of 24 VAC Transformer.
C
o
m
ú
n
-
G
R
I
S
C
o
m
m
o
n
-
G
R
A
Y
*Note:
Probe Wire Not Included
On Model AG-1250E
Figure 1
AG-4200E to
AG-4200E to
AG-4200E
AG-4200E
NOTE: WhenAG-4200E is wired correctly, the HVAC unit will shut-off upon condensate detection.
ATTENTION: Clean surface with included alcohol pad before mounting with adhesive tape.
Installation Instructions
Wiring the AquaGuard® AG-4100E, 4200E or 4300E - Water Sensor and Drain Port
AG-4100E
AG-4200E
AG-4300E
ATTENTION: Clean surface with included alcohol pad before mounting with adhesive tape.
Installation Instructions
Wiring the AquaGuard® AG-4100E, 4200E or 4300E - Water Sensor and Drain Port
AG-4100E
AG-4200E
AG-4300E
ATTENTION: Clean surface with included alcohol pad before mounting with adhesive tape.
Installation Instructions
Wiring the AquaGuard® AG-4100E, 4200E or 4300E - Water Sensor and Drain Port
AG-4100E
AG-4200E
AG-4300E
ATTENTIÓN:
AG-4200E to
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THEACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVEAND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
C
o
m
m
o
n
-
G
R
A
Y
C
o
m
ú
n
-
G
R
I
S
T
r
a
n
s
f
o
r
m
e
r
H
o
t
R
e
d
24 VAC
(Hot)
24 VAC
(Common)
*Note:
Probe Wire Not Included
On Model AG-1250E
COMPRESSOR
A. Connect typically “YELLOW” wire, going to “WallThermostat” to “Gray” “Common”
wires of AG-4200E.
C. Connect “RED”, “Input: 24VAC (Hot) wire ofAG-4200E to 24VAC (Hot) of 24VAC
Transformer or Thermostat’s “R” terminal.
D. Connect “BLACK”, “Input: 24VAC (Common) wire ofAG-4200E to 24VAC (Common)
secondary side of 24VAC Transformer or Thermostat’s “C” terminal.
E. Optional: Connect “WHITE”, “Normally Open” wire ofAG-4200E to the “WHITE” wire
ofAquaGuardAG-9100 ExternalAlarm (see Figure 1) or HomeAlarm System, or Communi-
cating System, etc...
NOTE: “WHITE”, “Normally Open” wire maximum capacity, 24VAC/1Amp.
2. Test theAG-4200E Secondary Pan Sensor (At start-up check initial amperage load) while the HVAC
unit is on and functioning correctly. See installation of theAG-4200E:
AG-4200E
NOTE: When theAG-4200E is wired correctly, (ONLY) the Compressor unit will shut-off
upon condensate detection.Air Handlerwill continue to run.
FOR CONNECTING TO SENSOR PORT
(A) NORMALLY CLOSED SIGNAL
C
o
m
m
o
n
-
GR
A
Y
Communication
C (Transformer Common)
Typically Black
C (Transformador Común)
Generalmente Negro
C
o
m
ú
n
-
G
R
IS
N
o
r
m
a
l
m
e
n
t
e
C
e
r
r
a
d
o
-
MOR
A
DO*
T
r
a
n
s
f
o
r
m
a
d
o
r
C
a
l
i
e
n
t
e
-
R
O
J
O
R
E
D
T
r
a
n
s
f
o
r
m
e
r
H
o
t
T
r
a
n
s
f
o
r
m
a
d
o
r
C
o
m
ú
n
-
N
E
G
R
O
T
r
a
n
s
f
o
r
m
e
r
C
o
m
m
o
n
-
B
L
A
C
K
INTERFACE
BOARD
N
o
r
m
a
l
m
e
n
t
e
A
b
i
e
r
t
o
-
B
l
a
n
c
o
*
N
o
r
m
a
l
l
y
O
p
e
n
-
W
H
I
T
E
*
Red Transformer Hot
Transformador Caliente ROJO
Sensor
Port
24 VAC
(Common)
24 VAC
(HOT)
Wiring
Sensor
Port
N
o
r
m
a
l
l
y
C
l
o
s
e
d
-
P
UR
P
L
E*
*Note Purple Wire:
Normally Open - WHITE
Normalmente Cerrado - BLANCO
*Note White Wire:
Normally Closed - PURPLE
Normalmente Cerrado - MORADO
*Note:
Probe Wire Not Included
On Model AG-1250E
FOR CONNECTING TO SENSOR PORT
(B) NORMALLY OPEN SIGNAL
*Optional
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTY AND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below.This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAYALL LABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIESARE EXCLUSIVE AND IN
LIEU OF ALLEXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THEAPPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Installation Instructions:
Titan, Goliath, Goliath Value and Goliath Furnace Series Secondary Condensate Pans & 4000E Series Switches
Work Safe, READ THIS!
ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING
INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.
1.
2. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE
3.
TITAN Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC
5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom
mended that a damp cloth be placed under the lines being brazed.
Rubber Gasket
Drain Housing
Sensor
GOLIATH VALUE, GOLIATH FURNACE Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Refer to Furnace/Air Handler instructions prior to installation.
2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
3. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
4. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
5. Insert rubber Vibration Isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
6.
7.
Riser Kit may be used to achieve additional 1” clearance between furnace and pan.
8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recom-
mended that a damp cloth be placed under the lines being brazed.
Caution: AquaGuard GOLIATH VALUE and GOLIATH FURNACE Series Drain Pans are not designed for hanging applications
GOLIATH Horizontal Drain Pan Installation:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
4. Insert rubber vibration isolators (Goliath Value, Goliath, and Goliath Furnace series only) in the most appropriate support receptacles
5.
installation.
6.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
GOLIATH FURNACE DRAIN PAN VERTICAL INSTALLATION:
(To ensure proper performance of product, instructions must be followed.)
1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.
2. Make sure drain pan exceeds equipment dimensions by a minimum of 1.5” per side.
3. Make sure the pan-mounting surface is level and free of any debris.
4. Insert one rubber Vibration Isolator at each strategic support location where the appliance makes contact with the drain pan. NOTE: It
5.
6.
additional 1” clearance between furnace and pan.
IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s
recommended that a damp cloth be placed under the lines being brazed.
24 VAC, 5 amps
AG4000E 07092013 C D B 0
NOTE: Must use
vibration Isolators
AG-4100E
AG-4200E
AG-4300E
Drain Housing
Drain Housing
Rubber Gasket
DRAIN FITTING AND SENSOR INSTALLATION
LIMITED WARRANTIES AND LIMITATION OF
LIABILITY
REGISTER YOUR PRODUCT ONLINE: www.rectorseal.com
1 YEAR SWITCHAND SENSOR LIMITED WARRANTYAND LIMITATION OF LIABILITY
The limitations of liability set forth below include body and all component parts as well as the product itself as a whole.
Rectorseal warrants to the original consumer purchaser (“Purchaser) of its AquaGuard switch and sensor products, that they are free from
defects in material or workmanship for a period of one (1) year from the date of purchase. If this product shall prove to be defective within the
one (1) year period from the date of purchase, it shall be repaired or replaced, at Rectorseal ‘s option, subject to the GENERAL TERMS and
CONDITIONS set forth below.
EXCLUSIONS
This warranty does not cover damages resulting from use of components or accessories not approved by Rectorseal. 3, and 10 YEAR SEC-
ONDARY DRAIN PAN LIMITED WARRANTYAND LIMITATION OF LIABILITY
This warranty applies only to secondary drain pans installed in the United States and Canada.
Rectorseal warrants to the original consumer purchaser (“Purchaser”) of its AquaGuard secondary drain pan products, that they are free from
defects in material or workmanship for a period of three (3) years for Titan pan models, ten (10) years for Goliath and Goliath Furnace
models, from the date of purchase. If this product shall prove to be defective within the three, five or ten (3, or 10) year period from the date of
purchase, it shall be repaired or replaced, at Rectorseal’s option, subject to the GENERAL TERMS and CONDITIONS set forth below. This
warranty extends only to the original consumer purchaser and is nontransferable.
EXCLUSIONS
This warranty does not cover damages resulting from the use of corrosive material (including, but not limited to: Acetone, MEK and
petro-leum-based products); nor damages resulting from use of components or accessories not approved by Rectorseal.
GENERAL TERMS AND CONDITIONS
To be eligible for the warranty the purchaser must provide Rectorseal with the following:
1. Proof of Purchase (Original Receipt)
2. Installer’s Testimony
3. Original Product
4. Original Work Order
5. Photos of Installation
PURCHASER MUST PAY ALLLABOR AND SHIPPING CHARGES NECESSARY TO REPLACE PRODUCT COVERED BY THIS WAR-
RANTY. This warranty shall not apply to acts of God, nor shall it apply to products which, in the sole judgment of Rectorseal have been subject
to negligence, abuse, accident, tampering, misapplication, alteration; nor due to improper installation, operation or maintenance or storage; nor
moved from its original place of installation; nor to other than normal application, use or service, including but not limited to, operational failures
caused by corrosion, rust or other foreign materials in the system. Requests for service under this warranty shall be made by returning the de-
fective product to the Retail outlet or to Rectorseal as soon as possible after the discovery of any alleged defect. Rectorseal will subsequently
take corrective action as promptly as reasonably possible. No requests for service under this warranty will be accepted if received more than
thirty-one (31) days after the term of the warranty.1hiswarranty sets forth Rectorseal’s sole obligation and purchaser’s exclusive remedy for de-
fective products. For your benefit and protection register your product online at www.rectorseal.com within thirty (30) days of installation. This
will initiate the Warranty period and will allow us to contact you, should it become necessary. In the absence of a recorded product registration,
the Warranty period will begin upon product shipment from Rectorseal. In the event that Rectorseal attempts to contact consumers regarding a
recall or other matter, and any damages occur, which could have been avoided by registration by the consumer, Rectorseal shall have no
liability. IN ALL CIRCUMSTANCES, RECTORSEAL’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE
PAID FOR THE PRODUCTALONE. Warranty claims must be registered with Rectorseal within thirty (30) days of damage or malfunction.
Rectorseal reserves the right to visit the site of the installation or to require documentation of the claim before assuming any responsibility
under the provisions of this Warranty.Consumer agrees to inspect the product at the time of installation for any reasonable discernable defects
and, further, agrees to inspect the product annually. Any damages occurring, which could have been avoided by proper inspection will not be
the responsibility of Rectorseal. RECTORSEAL SHALLNOT BE LIABLE FORANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT
DAMAGES WHATSOEVER TO THE PURCHASER ORANY THIRD PARTY.THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL EXPRESSED WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURATION OF THE APPLICA-
BLE EXPRESSED WARRANTIES PROVIDED HEREIN.
Some states do not allow the exclusion of limitation of incidental and consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other legal rights that vary from state to state. VENUE: Any purchaser or third party actions brought for any reason hereunder shall be
commenced in Houston, TX and no other jurisdiction, and such action shall be governed by and construed in accordance with the laws of the
State of Texas. Any notice herein shall be sent by certified or registered mail to 2601 Spenwick Drive, Houston, TX USA
RectorSeal® Houston, TX USA www.rectorseals.com US Patent Pending
Other RectorSeal Accessories manuals
Popular Accessories manuals by other brands
ORION TELESCOPES & BINOCULARS
ORION TELESCOPES & BINOCULARS 8893 instruction manual
RDI
RDI HORIZON Instructions for use
Stahl
Stahl SolConeX 8573/15 Series operating instructions
Craftsman
Craftsman 316.792410 Operator's manual
Campingaz
Campingaz Powerbox PLUS 24L 12V/230V Instructions for use
Hudora
Hudora 76909 INSTRUCTIONS ON ASSEMBLY AND USE
Profile
Profile 840000021 quick start guide
Blue Mark
Blue Mark DroneScout user manual
PASCO
PASCO PS-3208 Product guide
Emos
Emos P5724 user manual
Hearth and Home Technologies
Hearth and Home Technologies Heat-Zone-240V Air Duct Kit Installation and operation instructions
Hasselblad
Hasselblad DC POWER GRIP datasheet